| Age | Commit message (Collapse) | Author |
|---|
|
AP isolation has to be enabled on one VLAN interface only.
This patch moves the AP isolation attribute to the per-vlan
interface attribute set, enabling it to have a different
value depending on the selected vlan.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
My university will stop email service for alumni in january 2014, please
use my new e-mail address instead.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
When a node receives a unicast packet it checks if the source and the
destination client can communicate or not due to the AP isolation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
