| Age | Commit message (Collapse) | Author |
|---|
|
async_raid6_2data_recov() recovers two data disk failures
async_raid6_datap_recov() recovers a data disk and the P disk
These routines are a port of the synchronous versions found in
drivers/md/raid6recov.c. The primary difference is breaking out the xor
operations into separate calls to async_xor. Two helper routines are
introduced to perform scalar multiplication where needed.
async_sum_product() multiplies two sources by scalar coefficients and
then sums (xor) the result. async_mult() simply multiplies a single
source by a scalar.
This implemention also includes, in contrast to the original
synchronous-only code, special case handling for the 4-disk and 5-disk
array cases. In these situations the default N-disk algorithm will
present 0-source or 1-source operations to dma devices. To cover for
dma devices where the minimum source count is 2 we implement 4-disk and
5-disk handling in the recovery code.
[ Impact: asynchronous raid6 recovery routines for 2data and datap cases ]
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
[ Based on an original patch by Yuri Tikhonov ]
This adds support for doing asynchronous GF multiplication by adding
two additional functions to the async_tx API:
async_gen_syndrome() does simultaneous XOR and Galois field
multiplication of sources.
async_syndrome_val() validates the given source buffers against known P
and Q values.
When a request is made to run async_pq against more than the hardware
maximum number of supported sources we need to reuse the previous
generated P and Q values as sources into the next operation. Care must
be taken to remove Q from P' and P from Q'. For example to perform a 5
source pq op with hardware that only supports 4 sources at a time the
following approach is taken:
p, q = PQ(src0, src1, src2, src3, COEF({01}, {02}, {04}, {08}))
p', q' = PQ(p, q, q, src4, COEF({00}, {01}, {00}, {10}))
p' = p + q + q + src4 = p + src4
q' = {00}*p + {01}*q + {00}*q + {10}*src4 = q + {10}*src4
Note: 4 is the minimum acceptable maxpq otherwise we punt to
synchronous-software path.
The DMA_PREP_CONTINUE flag indicates to the driver to reuse p and q as
sources (in the above manner) and fill the remaining slots up to maxpq
with the new sources/coefficients.
Note1: Some devices have native support for P+Q continuation and can skip
this extra work. Devices with this capability can advertise it with
dma_set_maxpq. It is up to each driver how to handle the
DMA_PREP_CONTINUE flag.
Note2: The api supports disabling the generation of P when generating Q,
this is ignored by the synchronous path but is implemented by some dma
devices to save unnecessary writes. In this case the continuation
algorithm is simplified to only reuse Q as a source.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
async_xor() needs space to perform dma and page address conversions. In
most cases the code can simply reuse the struct page * array because the
size of the native pointer matches the size of a dma/page address. In
order to support archs where sizeof(dma_addr_t) is larger than
sizeof(struct page *), or to preserve the input parameters, we utilize a
memory region passed in by the caller.
Since the code is now prepared to handle the case where it cannot
perform address conversions on the stack, we no longer need the
!HIGHMEM64G dependency in drivers/dma/Kconfig.
[ Impact: don't clobber input buffers for address conversions ]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Prepare the api for the arrival of a new parameter, 'scribble'. This
will allow callers to identify scratchpad memory for dma address or page
address conversions. As this adds yet another parameter, take this
opportunity to convert the common submission parameters (flags,
dependency, callback, and callback argument) into an object that is
passed by reference.
Also, take this opportunity to fix up the kerneldoc and add notes about
the relevant ASYNC_TX_* flags for each routine.
[ Impact: moves api pass-by-value parameters to a pass-by-reference struct ]
Signed-off-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In support of inter-channel chaining async_tx utilizes an ack flag to
gate whether a dependent operation can be chained to another. While the
flag is not set the chain can be considered open for appending. Setting
the ack flag closes the chain and flags the descriptor for garbage
collection. The ASYNC_TX_DEP_ACK flag essentially means "close the
chain after adding this dependency". Since each operation can only have
one child the api now implicitly sets the ack flag at dependency
submission time. This removes an unnecessary management burden from
clients of the api.
[ Impact: clean up and enforce one dependency per operation ]
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
'zero_sum' does not properly describe the operation of generating parity
and checking that it validates against an existing buffer. Change the
name of the operation to 'val' (for 'validate'). This is in
anticipation of the p+q case where it is a requirement to identify the
target parity buffers separately from the source buffers, because the
target parity buffers will not have corresponding pq coefficients.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
"Wouldn't it be better if the dmaengine layer made sure it didn't pass
the same channel several times to a client?
I mean, you seem concerned that the memcpy() API should be transparent
and easy to use, but the whole registration interface is just
ridiculously complicated..."
- Haavard
The dmaengine and async_tx registration/allocation interface is indeed
needlessly complicated. This redesign has the following goals:
1/ Simplify reference counting: dma channels are not something one would
expect to be hotplugged, it should be an exceptional event handled by
drivers not something clients should be mandated to handle in a
callback. The common case channel removal event is 'rmmod <dma driver>',
which for simplicity should be disallowed if the channel is in use.
2/ Add an interface for requesting exclusive access to a channel
suitable to device-to-memory users.
3/ Convert all memory-to-memory users over to a common allocator, the goal
here is to not have competing channel allocation schemes. The only
competition should be between device-to-memory exclusive allocations and
the memory-to-memory usage case where channels are shared between
multiple "clients".
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Changes in v2:
* cleanups from Randy and Shannon
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
