summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/mtd
AgeCommit message (Collapse)Author
2014-01-03mtd: nand: davinci: reuse driver for Keystone archIvan Khoronzhuk
The Keystone arch has compatible nand device, so reuse it. In case with Keystone it depends on TI_AEMIF because AEMIF driver is responsible to set timings. See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Taras Kondratiuk <taras@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nand: davinci: adjust DT properties to MTD genericIvan Khoronzhuk
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt, nand-bus-width accordingly. So rename them in dts and documentation. Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Taras Kondratiuk <taras@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nand: davinci: extend description of bindingsIvan Khoronzhuk
Extend bindings for davinci_nand driver to be more clear. This is clarification only, without semantic changes. Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Taras Kondratiuk <taras@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nand: davinci: move bindings under mtdIvan Khoronzhuk
Move bindings under mtd. Do this in order to make davinci-nand driver usable by keystone architecture. Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Taras Kondratiuk <taras@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nand: pxa3xx: Add bad block handlingEzequiel Garcia
Add support for flash-based bad block table using Marvell's custom in-flash bad block table layout. The support is enabled a 'flash_bbt' platform data or device tree parameter. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Daniel Mack <zonque@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: nand: pxa3xx: devicetree binding updateEzequiel Garcia
Since the driver supports the new compatible string, the binding documentation must be updated to reflect it. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-01-03mtd: gpmi: add a new DT property to use the datasheet's minimum required ECCHuang Shijie
In default way, we use the ecc_strength/ecc_step size calculated by ourselves and use all the OOB area. This patch adds a new property : "fsl,use-minimum-ecc" If we enable it, we will firstly try to use the datasheet's minimum required ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields in the nand_chip{}). So we may have free space in the OOB area by using the minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's SLC NAND. If we fail to use the minimum ECC, we will use the legacy method to calculate the ecc_strength and ecc_step size. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2013-11-06mtd: nand: omap: combine different flavours of 1-bit hamming ecc schemesPekon Gupta
OMAP NAND driver currently supports multiple flavours of 1-bit Hamming ecc-scheme, like: - OMAP_ECC_HAMMING_CODE_DEFAULT 1-bit hamming ecc code using software library - OMAP_ECC_HAMMING_CODE_HW 1-bit hamming ecc-code using GPMC h/w engine - OMAP_ECC_HAMMING_CODE_HW_ROMCODE 1-bit hamming ecc-code using GPMC h/w engin with ecc-layout compatible to ROM code. This patch combines above multiple ecc-schemes into single implementation: - OMAP_ECC_HAM1_CODE_HW 1-bit hamming ecc-code using GPMC h/w engine with ROM-code compatible ecc-layout. Signed-off-by: Pekon Gupta <pekon@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2013-11-06ARM: OMAP2+: cleaned-up DT support of various ECC schemesPekon Gupta
OMAP NAND driver support multiple ECC scheme, which can used in different flavours, depending on in-build Hardware engines present on SoC. This patch updates following in DT bindings related to sectionion of ecc-schemes - ti,elm-id: replaces elm_id (maintains backward compatibility) - ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme depends on ti,elm-id. (supported values ham1, bch4, and bch8) - maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode) Below table shows different flavours of ecc-schemes supported by OMAP devices +---------------------------------------+---------------+---------------+ | ECC scheme |ECC calculation|Error detection| +---------------------------------------+---------------+---------------+ |OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W | |(requires CONFIG_MTD_NAND_ECC_BCH) | | | +---------------------------------------+---------------+---------------+ |OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) | |(requires CONFIG_MTD_NAND_OMAP_BCH && | | | | ti,elm-id in DT) | | | +---------------------------------------+---------------+---------------+ To optimize footprint of omap2-nand driver, selection of some ECC schemes also require enabling following Kconfigs, in addition to setting appropriate DT bindings - Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software - Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine Signed-off-by: Pekon Gupta <pekon@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2013-08-05mtd: ofpart: add compatible check for child nodesJosh Wu
In case that the nand device will support some features like Nand Flash Controller, we want to make the sub feature as a sub node of nand device. Use such organization it is easy to enable/disable feature, also it is back compatible and more readable. If the sub-node has a compatible property then it is a driver not partition. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> [ added a missing newline -Brian ] Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-08-05mtd: atmel_nand: enable Nand Flash Controller (NFC) write via sramJosh Wu
This patch enable writing nand flash via NFC SRAM. It will minimize the CPU overhead. The SRAM write only support ECC_NONE and ECC_HW with PMECC. To enable this NFC write by SRAM feature, you can add a string in dts under NFC driver node. This driver has been tested on SAMA5D3X-EK with JFFS2, YAFFS2, UBIFS and mtd-utils. Here is part of mtd_speedtest (writing test) result, compare with non-NFC writing, it reduces %65 cpu load with loss %12 speed. - commands use to test: # insmod /mnt/mtd_speedtest.ko dev=2 & # top -n 30 -d 1 | grep speedtest - test result: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 mtd_speedtest: testing eraseblock write speed 509 495 root D 1164 0% 7% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 8% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 5% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5194 KiB/s mtd_speedtest: testing page write speed 509 495 root D 1164 0% 32% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 27% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 25% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 30% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5024 KiB/s Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-08-05mtd: atmel_nand: add Nand Flash Controller (NFC) supportJosh Wu
Nand Flash Controller (NFC) can handle automatic transfers, sending the commands and address cycles to the NAND Flash. To use NFC in this driver, user needs to add NFC child node in nand flash driver. The NFC child node includes NFC's compatible string and regiters of the address and size of NFC command registers, NFC registers (embedded in HSMC) and NFC SRAM. Also user need to set up the HSMC irq, which use to check whether nfc command is finish or not. This driver has been tested on SAMA5D3X-EK board with JFFS2, YAFFS, UBIFS and mtd-utils. I put the part of the mtd_speedtest result here for your information. >From the mtd_speedtest, we can see the NFC will reduce the %50 of cpu load when writing nand flash. No change when reading. In the meantime, the speed will be slow about %8. - commands use to test: #insmod /mnt/mtd_speedtest.ko dev=2 & #top -n 30 -d 1 | grep speedtest - test result: Before the patch: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 515 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 99% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5768 KiB/s mtd_speedtest: testing eraseblock read speed 515 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock read speed is 5932 KiB/s mtd_speedtest: testing page write speed 515 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 98% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5770 KiB/s mtd_speedtest: testing page read speed 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2 515 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page read speed is 5910 KiB/s After the patch: ================================================= mtd_speedtest: MTD device: 2 mtd_speedtest: MTD device size 41943040, eraseblock size 131072, page size 2048, count of eraseblocks 320, pages per eraseblock 64, OOB size 64 mtd_speedtest: testing eraseblock write speed 509 495 root D 1164 0% 49% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock write speed is 5370 KiB/s mtd_speedtest: testing eraseblock read speed 509 495 root R 1164 0% 92% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 91% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 95% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: eraseblock read speed is 5715 KiB/s mtd_speedtest: testing page write speed 509 495 root D 1164 0% 48% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 47% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root D 1164 0% 50% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page write speed is 5224 KiB/s mtd_speedtest: testing page read speed 509 495 root R 1164 0% 89% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 94% insmod /mnt/mtd_speedtest.ko dev=2 509 495 root R 1164 0% 93% insmod /mnt/mtd_speedtest.ko dev=2 mtd_speedtest: page read speed is 5641 KiB/s Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-08-05mtd: atmel_nand: add a new dt binding item for nand dma supportJosh Wu
This patch will set the nand dma support in dts. Since we will not use cpu_is_xxx() in nand driver. We needn't include the mach/cpu.h any more. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-08-05mtd: nand: fsmc: update of OF supportMian Yousaf Kaukab
Add nand bank selection and timings to the device tree bindings. Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> [Added some documentation] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-05-16ARM: OMAP2+: Allow NAND transfer mode to be specified in DTMark Jackson
OMAP devices support various NAND transfer modes. Currently all device-tree definitions will use the default "prefetch polled" mode, so this patch enables the transfer mode to be specified in the device-tree. Signed-off-by: Mark Jackson <mpfj@newflow.co.uk> Acked-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-05-09Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes From Tony Lindgren: Omap fixes for things that were discovered during the merge window: - Few GPMC fixes and binding doc updates noted after sending pull requests for the GPMC branch. - Board fixes for beagle usb host and rx51 spi probe order - SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error handling fixes Then few minor things that are not strictly fixes but are good to get out of the way: - Add missing legacy mux registers for am/dm73x gpio - Add detection for am33xx pg2.1 silicon - Enable twl4030 audio modules in defconfig * tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si omap: mux: add AM/DM37x gpios ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init() ARM: OMAP2+: omap_device: use late_initcall_sync ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx ARM: OMAP2+: only WARN if a GPMC child probe function fail ARM: OMAP2+: only search for GPMC DT child nodes on probe Documentation: dt: update properties in TI GPMC NAND example Documentation: dt: update TI GPMC ethernet binding properties Signed-off-by: Olof Johansson <olof@lixom.net>
2013-05-09Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD update from David Woodhouse: - Lots of cleanups from Artem, including deletion of some obsolete drivers - Support partitions larger than 4GiB in device tree - Support for new SPI chips * tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits) mtd: omap2: Use module_platform_driver() mtd: bf5xx_nand: Use module_platform_driver() mtd: denali_dt: Remove redundant use of of_match_ptr mtd: denali_dt: Change return value to fix smatch warning mtd: denali_dt: Use module_platform_driver() mtd: denali_dt: Fix incorrect error check mtd: nand: subpage write support for hardware based ECC schemes mtd: omap2: use msecs_to_jiffies() mtd: nand_ids: use size macros mtd: nand_ids: improve LEGACY_ID_NAND macro a bit mtd: add 4 Toshiba nand chips for the full-id case mtd: add the support to parse out the full-id nand type mtd: add new fields to nand_flash_dev{} mtd: sh_flctl: Use of_match_ptr() macro mtd: gpio: Use of_match_ptr() macro mtd: gpio: Use devm_kzalloc() mtd: davinci_nand: Use of_match_ptr() mtd: dataflash: Use of_match_ptr() macro mtd: remove h720x flash support mtd: onenand: remove OneNAND simulator ...
2013-05-08Merge branch 'omap-gpmc-fixes-for-v3.10' of git://github.com/jonhunter/linux ↵Tony Lindgren
into fixes
2013-05-07Merge tag 'dt-for-linus-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC device tree updates (part 2) from Arnd Bergmann: "These are mostly new device tree bindings for existing drivers, as well as changes to the device tree source files to add support for those devices, and a couple of new boards, most notably Samsung's Exynos5 based Chromebook. The changes depend on earlier platform specific updates and touch the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci." * tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits) ARM: exynos: dts: cros5250: add EC device ARM: dts: Add sbs-battery for exynos5250-snow ARM: dts: Add i2c-arbitrator bus for exynos5250-snow ARM: dts: add mshc controller node for Exynos4x12 SoCs ARM: dts: Add chip-id controller node on Exynos4/5 SoC ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree ARM: davinci: da850-evm: add SPI flash support ARM: davinci: da850: override SPI DT node device name ARM: davinci: da850: add SPI1 DT node spi/davinci: add DT binding documentation spi/davinci: no wildcards in DT compatible property ARM: dts: mvebu: Convert mvebu device tree files to 64 bits ARM: dts: mvebu: introduce internal-regs node ARM: dts: mvebu: Convert all the mvebu files to use the range property ARM: dts: mvebu: move all peripherals inside soc ARM: dts: mvebu: fix cpus section indentation ARM: davinci: da850: add EHRPWM & ECAP DT node ARM/dts: OMAP3: fix pinctrl-single configuration ARM: dts: Add OMAP3430 SDP NOR flash memory binding ARM: dts: Add NOR flash bindings for OMAP2420 H4 ...
2013-04-30Documentation: dt: update properties in TI GPMC NAND exampleJon Hunter
The GPMC timing properties for device-tree have been updated by adding a "-ns" or "-ps" suffix to indicate the units of time the property represents. Therefore, update the timing property names for TI GPMC NAND example. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-05mtd: ofpart: support partitions of 4 GiB and largerJoe Schaack
Previously, partitions were limited to less than 4 GiB in size because the address and size were read as 32-bit values. Add support for 64-bit values to support devices of 4 GiB and larger. Signed-off-by: Joe Schaack <jschaack@xes-inc.com> Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2013-04-04mtd: gpmi: move to use generic DMA helperShawn Guo
With the generic DMA device tree helper supported by mxs-dma driver, client devices only need to call dma_request_slave_channel() for requesting a DMA channel from dmaengine. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2013-04-03ARM: OMAP2+: Convert ONENAND to retrieve GPMC settings from DTJon Hunter
When booting with device-tree, retrieve GPMC settings for ONENAND from the device-tree blob. This will allow us to remove all static settings stored in the gpmc-nand.c in the future once the migration to device-tree is complete. The user must now specify the ONENAND device width in the device-tree binding so that the GPMC can be programmed correctly. Therefore, update the device-tree binding documentation for ONENAND devices connected to the GPMC to reflect this. Please note that this does not include GPMC timings for ONENAND. The timings are being calculated at runtime. There is some legacy code that only enables read wait monitoring for non-OMAP3 devices. There are no known OMAP3 device issues that prevent this feature being enabled and so when booting with device-tree use the wait-monitoring settings described in the device-tree blob. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
2013-04-03ARM: OMAP2+: Add device-tree support for NOR flashJon Hunter
NOR flash is not currently supported when booting with device-tree on OMAP2+ devices. Add support to detect and configure NOR devices when booting with device-tree. Add documentation for the TI GPMC NOR binding. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
2013-03-02Merge tag 'for-linus-20130301' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD update from David Woodhouse: "Fairly unexciting MTD merge for 3.9: - misc clean-ups in the MTD command-line partitioning parser (cmdlinepart) - add flash locking support for STmicro chips serial flash chips, as well as for CFI command set 2 chips. - new driver for the ELM error correction HW module found in various TI chips, enable the OMAP NAND driver to use the ELM HW error correction - added number of new serial flash IDs - various fixes and improvements in the gpmi NAND driver - bcm47xx NAND driver improvements - make the mtdpart module actually removable" * tag 'for-linus-20130301' of git://git.infradead.org/linux-mtd: (45 commits) mtd: map: BUG() in non handled cases mtd: bcm47xxnflash: use pr_fmt for module prefix in messages mtd: davinci_nand: Use managed resources mtd: mtd_torturetest can cause stack overflows mtd: physmap_of: Convert device allocation to managed devm_kzalloc() mtd: at91: atmel_nand: for PMECC, add code to check the ONFI parameter ECC requirement. mtd: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is optional. mtd: atmel_nand: avoid to report an error when lookup table offset is 0. mtd: bcm47xxsflash: adjust names of bus-specific functions mtd: bcm47xxpart: improve probing of nvram partition mtd: bcm47xxpart: add support for other erase sizes mtd: bcm47xxnflash: register this as normal driver mtd: bcm47xxnflash: fix message mtd: bcm47xxsflash: register this as normal driver mtd: bcm47xxsflash: write number of written bytes mtd: gpmi: add sanity check for the ECC mtd: gpmi: set the Golois Field bit for mx6q's BCH mtd: devices: elm: Removes <xx> literals in elm DT node mtd: gpmi: fix a dereferencing freed memory error mtd: fix the wrong timeo for panic_nand_wait() ...
2013-02-21Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds
Pull ARM SoC device tree conversions from Arnd Bergmann: "These are device tree conversions for a number of platforms, with the intention of turning code from board files into device tree descriptions. Notable changes are: - davinci bindings for pinctrl, MTD, RTC, watchdog and i2c - nomadik bindings for all devices, removing the board files - bcm2835 bindings for mmc and i2c - tegra bindings for hdmi, keyboard, audio, as well as some updates - at91 bindings for hardware ecc and for devices on RM9200 - mxs bindings for cfa100xx - sunxi support for Miniand Hackberry board" * tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (72 commits) Revert "sunxi: a10-cubieboard: Add user LEDs to the device tree" Revert "sunxi: a13-olinuxino: Add user LED to the device tree" clk: tegra: initialise parent of uart clocks ARM: tegra: remove clock-frequency properties from serial nodes clk: tegra: fix driver to match DT binding clk: tegra: local arrays should be static clk: tegra: Add missing spinlock for hclk and pclk clk: tegra: Implement locking for super clock clk: tegra: fix wrong clock index between se to sata_cold sunxi: a13-olinuxino: Add user LED to the device tree ARM: davinci: da850 DT: add support for machine reboot ARM: davinci: da850: add wdt DT node ARM: davinci: da850: add DT node for I2C0 ARM: at91: at91sam9n12: add DT parameters to enable PMECC ARM: at91: at91sam9x5: add DT parameters to enable PMECC ARM: at91: add EMAC bindings to RM9200 DT ARM: at91: add SSC bindings to RM9200 DT ARM: at91: add MMC bindings to RM9200 DT ARM: at91: Animeo IP: enable watchdog support ARM: nomadik: fix OF compilation regression ...
2013-02-04mtd: devices: elm: Removes <xx> literals in elm DT nodePhilip Avinash
As part of removing generalized dependency, replace <xx> literal fields in DT compatible field with <52> for am335x platforms. Signed-off-by: Philip Avinash <avinashphilip@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2013-02-04mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) lockingStefan Roese
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This patch adds support for this locking/unlocking mechanism. It is needed on some platforms, since newer U-Boot versions do support this PPB locking and protect for example their environment sector(s) this way. This PPB locking/unlocking will be enabled for all devices supported by cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect scheme). Please note that PPB locking does support sector-by-sector locking. But the whole chip can only be unlocked together. So unlocking one sector will automatically unlock all sectors of this device. Because of this chip limitation, the PPB unlocking function saves the current locking status of all sectors before unlocking the whole device. After unlocking the saved locking status is re-configured. This way only the addressed sectors will be unlocked. To selectively enable this advanced sector protection mechanism, the device-tree property "use-advanced-sector-protection" has been created. To enable support for this locking this property needs to be present in the flash DT node. E.g.: nor_flash@0,0 { compatible = "amd,s29gl256n", "cfi-flash"; bank-width = <2>; use-advanced-sector-protection; ... Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash devices. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2013-02-04mtd: devices: elm: Add support for ELM error correctionPhilip Avinash
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme error correction. For now only 4 & 8 bit support is added Signed-off-by: Philip Avinash <avinashphilip@ti.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2013-02-01ARM: OMAP2+: gpmc: Add device tree documentation for elm handlePhilip Avinash
In case ELM module available, omap2 NAND driver can opt for hardware correction method for bit flip errors in NAND flash with BCH. Hence the detection of ELM module is done through devicetree population of elm_id. This patch update device tree documentation for gpmc-nand for elm-id data population. Signed-off-by: Philip Avinash <avinashphilip@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-02-01ARM: OMAP2+: gpmc: add DT bindings for OneNANDEzequiel Garcia
This patch adds device tree bindings for OMAP OneNAND devices. Tested on an OMAP3 3430 IGEPv2 board. Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-01-28ARM: nomadik: add FSMC NANDLinus Walleij
This adds the FSMC NAND driver and flash partitions to the Nomadik device tree. The only compatible string accepted by this driver is currently "st,spear600-fsmc-nand" which is inappropriate for this system, so this patch adds the compatible value "stericsson,fsmc-nand" as well. Cc: linux-mtd@vger.kernel.org Cc: David Woodhouse <dwmw2@infradead.org> Cc: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-01-15ARM: OMAP: gpmc: add DT bindings for GPMC timings and NANDDaniel Mack
This patch adds basic DT bindings for OMAP GPMC. The actual peripherals are instantiated from child nodes within the GPMC node, and the only type of device that is currently supported is NAND. Code was added to parse the generic GPMC timing parameters and some documentation with examples on how to use them. Successfully tested on an AM33xx board. Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> [tony@atomide.com: updated to apply] Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-11-16mtd: physmap_of: allow to specify the mtd name for retro compatiblityJean-Christophe PLAGNIOL-VILLARD
linux,mtd-name allow to specify the mtd name for retro capability with physmap-flash drivers as boot loader pass the mtd partition via the old device name physmap-flash. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: sh_flctl: Add device tree supportBastian Hecht
The flctl can now be probed via device tree setup in addition to the existing platform data way. SoC specific setup data is set in the .data member of the OF match, so kept within the driver itself, while board/user specific setup - like partitioning - is taken from the device tree. Actual configuration is added for the SoC sh7372. Signed-off-by: Bastian Hecht <hechtb@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: fsmc_nand: pass the ale and cmd resource via resourceJean-Christophe PLAGNIOL-VILLARD
Do not use the platform_data to pass resource and be smart in the drivers. Just pass it via resource Switch to devm_request_and_ioremap at the sametime Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-By: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: denali: add a DT driverDinh Nguyen
Add a device tree version of the Denali NAND driver. Based on an original patch from Jamie Iles to add a MMIO version of this driver. Signed-off-by: Dinh Nguyen <dinguyen@altera.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-11-15mtd: m25p80: Make fast read configurable via DTMarek Vasut
Add DT property "m25p,fast-read" that signalises the particular chip supports "fast read" opcode. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2012-10-09Merge tag 'disintegrate-mtd-20121009' of ↵David Woodhouse
git://git.infradead.org/users/dhowells/linux-headers UAPI Disintegration 2012-10-09 Conflicts: MAINTAINERS arch/arm/configs/bcmring_defconfig arch/arm/mach-imx/clk-imx51-imx53.c drivers/mtd/nand/Kconfig drivers/mtd/nand/bcm_umi_nand.c drivers/mtd/nand/nand_bcm_umi.h drivers/mtd/nand/orion_nand.c
2012-09-29mtd: physmap_of: Add "no-unaligned-direct-access" DT propertyStefan Roese
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause problems with JFFS2 usage, as the local bus (LPB) doesn't support unaligned accesses as implemented in the JFFS2 code via memcpy(). By defining "no-unaligned-direct-access", the flash will not be exposed directly to the MTD users (e.g. JFFS2) any more. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-08-22Merge tag 'v3.6-rc2' of ↵David Woodhouse
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux Having missed the merge window, update to 3.6-rc2 to avoid conflicts with new patches. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-08-16MTD: pxa3xx-nand: add devicetree bindingsDaniel Mack
This patch contains a hack to get the DMA resources of the device when probed from a devicetree node. This can be removed once a generic DMA controller framework lands. A mtd_part_parser_data is passed mtd_device_parse_register which contains a reference to the device node, so MTD partitions can be added as children. Signed-off-by: Daniel Mack <zonque@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
2012-07-25Merge branch 'v3.5-rc7-fixes' of git://github.com/lunn/linux into fixesArnd Bergmann
From Andrew Lunn <andrew@lunn.ch>: * 'v3.5-rc7-fixes' of git://github.com/lunn/linux: ARM: Kirkwood: Replace mrvl with marvell ARM: Orion: fix driver probe error handling with respect to clk ARM: Dove: Fixup ge00 initialisation ARM: Kirkwood: Fix PHY disable clk problems ARM: Kirkwood: Ensure runit clock always ticks. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-07-25ARM: Kirkwood: Replace mrvl with marvellAndrew Lunn
It has been decided to use marvell, not mrvl, in the compatibility property. Search & replace. Signed-off-by: Andrew Lunn <andrew@lunn.ch>
2012-07-16mtd: gpmi: add on-flash BBT support for gpmi nandHuang Shijie
add the on flash bbt support for gpmi nand driver. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: add LPC32xx MLC NAND driverRoland Stigge
This patch adds a driver for the MLC NAND controller of the LPC32xx SoC. [dwmw2: 21st century pedantry] Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: at91: add dt parameters for Atmel PMECCJosh Wu
Add DT support for PMECC parameters. Signed-off-by: Hong Xu <hong.xu@atmel.com> Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06mtd: add LPC32xx SLC NAND driverRoland Stigge
This patch adds support for the SLC NAND controller inside the LPC32xx SoC. [dwmw2: 21st century pedantry] Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2012-07-06of: fix a few typos in the binding documentationRob Herring
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [rob herring: drop conflicting atmel-nand.txt changes] Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-06-01Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull mtd update from David Woodhouse: - More robust parsing especially of xattr data in JFFS2 - Updates to mxc_nand and gpmi drivers to support new boards and device tree - Improve consistency of information about ECC strength in NAND devices - Clean up partition handling of plat_nand - Support NAND drivers without dedicated access to OOB area - BCH hardware ECC support for OMAP - Other fixes and cleanups, and a few new device IDs Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to added include files next to each other. * tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits) mtd: mxc_nand: move ecc strengh setup before nand_scan_tail mtd: block2mtd: fix recursive call of mtd_writev mtd: gpmi-nand: define ecc.strength mtd: of_parts: fix breakage in Kconfig mtd: nand: fix scan_read_raw_oob mtd: docg3 fix in-middle of blocks reads mtd: cfi_cmdset_0002: Slight cleanup of fixup messages mtd: add fixup for S29NS512P NOR flash. jffs2: allow to complete xattr integrity check on first GC scan jffs2: allow to discriminate between recoverable and non-recoverable errors mtd: nand: omap: add support for hardware BCH ecc ARM: OMAP3: gpmc: add BCH ecc api and modes mtd: nand: check the return code of 'read_oob/read_oob_raw' mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw' mtd: m25p80: Add support for Winbond W25Q80BW jffs2: get rid of jffs2_sync_super jffs2: remove unnecessary GC pass on sync jffs2: remove unnecessary GC pass on umount jffs2: remove lock_super mtd: gpmi: add gpmi support for mx6q ...
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-27 02:44:53 +0000