| Age | Commit message (Collapse) | Author |
|---|
|
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
|
|
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
|
|
Pull arm-soc device tree description updates from Arnd Bergmann:
"This branch contains two kinds of updates: Some platforms in the
process of getting converted to device tree based booting, and the
platform specific patches necessary for that are included here.
Other platforms are already converted, so we just need to update the
actual device tree source files and the binding documents to add
support for new board and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents."
Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: LPC32xx: Add PWM to base dts file
ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
...
|
|
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.6:
Core:
- Rename cd-gpio to slot-gpio and extend it to support more slot GPIO
functions, such as write-protect.
- Add a function to get regulators (Vdd and Vccq) for a host.
Drivers:
- sdhci-pxav2, sdhci-pxav3: Add device tree support.
- sdhi: Add device tree support.
- sh_mmcif: Add support for regulators, device tree, slot-gpio.
- tmio: Add regulator support, use slot-gpio."
* tag 'mmc-merge-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (62 commits)
mmc: sdhci-dove: Prepare for common clock framework
mmc: sdhci-dove: Add SDHCI_QUIRK_NO_HISPD_BIT
mmc: omap_hsmmc: ensure probe returns error upon resource failure
mmc: mxs-mmc: Add wp-inverted property
mmc: esdhc: Fix DMA_MASK to not break mx25 DMA access
mmc: core: reset signal voltage on power up
mmc: sd: Fix sd current limit setting
mmc: omap_hsmmc: add clk_prepare and clk_unprepare
mmc: sdhci: When a UHS switch fails, cycle power if regulator is used
mmc: atmel-mci: modify CLKDIV displaying in debugfs
mmc: atmel-mci: fix incorrect setting of host->data to NULL
mmc: sdhci: poll for card even when card is logically unremovable
mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
mmc: sdio: Change pr_warning to pr_warn_ratelimited
mmc: core: Simplify and fix for SD switch processing
mmc: sdhci: restore host settings when card is removed
mmc: sdhci: fix incorrect command used in tuning
mmc: sdhci-pci: CaFe has broken card detection
mmc: sdhci: Report failure reasons for all cases in sdhci_add_host()
mmc: s3cmci: Convert s3cmci driver to gpiolib API
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Lots and lots of fixes from Axel and some others here, plus some
framework enhancements which continue the theme of factoring code out
of the drivers and into the core.
- Initial framework support for GPIO controlled enable signals,
saving a bunch of code in drivers.
- Move fixed regulator enable time and voltage mapping table
specifications to data.
- Used some of the recent framework enhancements to make voltage
change notifications more useful, passing the voltage in as an
argument to the notification.
- Fixed the pattern used for finding individual regulators on a
device to not rely on the node name, supporting the use of multiple
PMICs of the same type in the system.
- New drivers for Maxim MAX77686, TI LP872x and LP8788, Samsung
S2MPS11, and Wolfson Arizona microphone supplies and LDOs."
* tag 'regulator-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (176 commits)
regulator: add new lp8788 regulator driver
regulator: mc13xxx: Remove extern function declaration for mc13xxx_sw_regulator
regulator: tps65910: set input_supply on desc unconditionally
regulator: palmas: Fix calcuating selector in palmas_map_voltage_smps
regulator: lp872x: Simplify implementation of lp872x_find_regulator_init_data()
regulator: twl: Fix list_voltate for twl6030ldo_ops
regulator: twl: Convert twl6030ldo_ops to [get|set]_voltage_sel
regulator: twl: Fix the formula to calculate vsel and voltage for twl6030ldo
regulator: s5m8767: Properly handle gpio_request failure
regulator: max8997: Properly handle gpio_request failure
regulator: tps62360: use devm_* for gpio request
regulator: tps6586x: add support for input supply
regulator: tps65217: Add device tree support
regulator: aat2870: Remove unused min_uV and max_uV from struct aat2870_regulator
regulator: aat2870: Convert to regulator_list_voltage_table
regulator: da9052: initialize of_node param for regulator register
regulator: Add REGULATOR_STATUS_UNDEFINED.
regulator: Fix a typo in regulator_mode_to_status() core function.
regulator: s2mps11: Use sec_reg_write rather than sec_reg_update when mask is 0xff
regulator: s2mps11: Fix wrong setting for config.dev
...
|
|
Tested on an OLPC XO-1.75. (MMP2, sdhci-pxav3, CONFIG_MACH_MMP2_DT=y)
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
git://git.linaro.org/people/ljones/linux-3.0-ux500 into next/dt
From Lee Jones <lee.jones@linaro.org>:
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
ARM: ux500: Enable LED heartbeat functionality on Snowball
ARM: ux500: Add support for input/ponkey into the db8500's Device Tree
ARM: ux500: Add a ab8500-gpadc node to the db8500 Device Tree
ARM: ux500: Enable the user LED on Snowball via Device Tree
ARM: ux500: Kconfig: Compile in leds-gpio support for Snowball
ARM: ux500: Provide auxdata to be used as name base clock search for nmk-i2c
ARM: ux500: Remove unused i2c platform_data initialisation code
ARM: ux500: Enable Device Tree support mmci for Snowball
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Bindings for DMA channels are still under discussion and will
change once this has been resolved. Therefore we mark them
the newly added ones as preliminary. Let's hope nobody starts
relying on them...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim <kgene.kim@samsung.com>:
It is for supporting spi dt for exynos4210 and exynos5250, and got the
ack from Grant Likely for spi driver.
Note: Since this is including spi driver changes, so it was made based
on next/devel-dma-ops which touches same file, Samsung spi driver for
avoiding bad conflicts.
* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: EXYNOS: Add device tree node for EXYNOS4 interrupt combiner controller
spi: s3c64xx: add device tree support
spi: s3c64xx: Remove the 'set_level' callback from controller data
ARM: SAMSUNG: Modify s3c64xx_spi{0|1|2}_set_platdata function
ARM: SAMSUNG: Remove pdev pointer parameter from spi gpio setup functions
spi: s3c64xx: move controller information into driver data
spi: s3c64xx: remove unused S3C64XX_SPI_ST_TRLCNTZ macro
ARM: S3C64XX: Add a new dma request id for device tree based dma channel lookup
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Patches from Alexander Shiyan <shc_work@mail.ru>:
* clps711x/cleanup:
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Set the supply_name in the regulator descriptor unconditionally
and make this parameter as required parameter in the device
node for successfully registration of the regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Linux 3.5-rc7
|
|
The original pin registers table is derived from u-boot mainline,
but somehow it was found missing some mux functions for USBOTG_ID.
We added it at the bottom by following the exist pin function ids,
then it will not break the exist using of pin function id in dts file.
Reported-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/dt
From Sekhar Nori <nsekhar@ti.com>:
DaVinci DT support
Add DT support for DaVinci cp_intc interrupt controller
* tag 'davinci-v3.6-dt' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: cp_intc: Add OF support for TI interrupt controller
ARM: davinci: add runtime PM support for clock management
ARM: davinci: cp_intc: Add irq domain support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
prefixes
Any non-standard property should contain the vendor's identifier which
should be perpended onto the property name followed by a comma. This
aids in name-space collision prevention. This patch ensures the
sleepmode property adheres to the rules.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for device based discovery.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This commit adds device tree support for tps65217 pmic. And usage
details are added to device tree documentation. Driver is tested
by using kernel module with regulator set and get APIs.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of imx device tree changes for 3.6.
* 'imx/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: ensure ANATOP controller is available
ARM: dts: imx6q-sabrelite: add ecspi1 pinctrl support
ARM: dts: imx6q-sabrelite: add usb devices
ARM: imx6q: disable usb charger detector
ARM: imx6q: add usbphy clocks
ARM: imx6q: add usb controller clock lookups
ARM: dts: imx: update #interrupt-cells for gpio nodes
bindings: update imx and mxs #gpio-cells
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren <tony@atomide.com>:
Device tree related patches for omaps
* tag 'omap-devel-dt-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: New dts file for PandaBoardES (4460)
arm/dts: omap4-panda: Audio support for PandaBoard 4430
arm/dts: omap4-sdp: Enable audio support via device tree
arm/dts: omap4-sdp: Add support for twl6040
arm/dts: omap4-sdp: Add fixed regulator to represent VBAT
arm/dts: omap4: Add entry for OMAP DMIC IP
arm/dts: omap4: Add entry for OMAP McPDM IP
arm/dts: am33xx wdt node
arm/dts: remove MMC/SD and SPI related entries from am33xx.dtsi
watchdog: omap_wdt: add device tree support
ARM: OMAP: avoid build wdt platform device if with dt support
arm/dts: add wdt node for omap3 and omap4
arm/dts: OMAP4: Add Variscite OMAP4 System-On-Modeule support
arm/dts: Add support for AM335x BeagleBone
arm/dts: Add support for AM335x EVM
arm/dts: Add initial DT support for AM33XX SoC family
arm/dts: omap3-evm: Add i2c and twl4030 support
arm/dts: Add support for TI AM3517/05 EVM board
arm/dts: OMAP2: Add support for OMAP2420H4 Board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
New pull requests are based on Linux 3.5-rc6
|
|
Dependency for tegra/dt branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make a common device tree glue for clocksource/dw_apb_timer.
Move mach-picoxcell/time.c to be a generic device tree application
of the dw_apb_timer.
Configure mach-picoxcell to use the dw_apb_timer_of device tree
implementation in drivers/clocksource.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Even though these aren't parsed by the MMC driver, make clear that
they're required by the OF core. (Also, a few typo fixes.)
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Now that we have common bindings for MMC, rewrite the individual
bindings to inherit from mmc.txt and describe their differences.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/newsoc
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
|
|
Adding the minimal support for OMAP5 evm board
with device tree.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Add wdt node to support dt.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains various minor cleanups, such as binding and .dts
renames, DT content cleanup, SDHCI support-8bit property usage cleanup, and
removal of some unnecessary sleep code.
* 'for-3.6/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra: rename board files to match SoC
ASoC: tegra: simplify Kconfig dependencies
ARM: dt: tegra: remove legacy support-8bit property
mmc: tegra: use bus-width property instead of support-8bit
ARM: tegra: Remove flow controller programming
dt: name all Tegra binding docs consistently
ARM: tegra20: Rename "emc" to "memory-controller"
ARM: dt: tegra20: Rename "emc" to "memory-controller"
ARM: tegra{20,30}: Rename "mc" to "memory-controller"
ARM: dt: tegra{20,30}.dtsi: Rename "mc" to "memory-controller"
amba: tegra-ahb: Remove empty *_remove()
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The of_get_named_gpio_flags can retrieve the second cell of
gpio-specifier as the "flags". The imx and mxs gpio driver do not
have their own .xlate callback, which means of_gpio_simple_xlate is
used and it's a 1:1 mapping between gpio controller flags and Linux
"enum of_gpio_flags".
Update imx and mxs bindings document to make it clear.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add support for input supply in DT parsing of node.
The input supply will be provided by the property
"vin-supply" in the regulator node.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add the policy for regulator DT such that if device have multiple
regulator and its binding contains a child node that describes each
regulator then each regulator child node must have the property
"regulator-compatible" which matches with regulator name of their
hardware counterparts.
Modify the DT documentation of regulator devices to reflect this
policy.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add a function to initialize the Common Platform Interrupt Controller
(cp_intc) from TI used on OMAP-L1x SoCs using a device tree node.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add a simple device tree probe support for mxsfb driver. Before
a common binding for struct fb_videomode is available, the driver will
keep using struct mxsfb_platform_data. That said, platform code will
use auxdata to attach mxsfb_platform_data for device tree boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: rtc-linux@googlegroups.com
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Allow device tree probing.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: <linux-serial@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Subodh Nijsure <snijsure@grid-net.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a third cell to define irq priority.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Linux 3.5-rc4 contains patches which conflict with some of the
development work.
|
|
Due to the lack of a generic clock API we'd had the 32kHz clock in the
regulator driver but this is definitely a Linux-specific thing and now
we have a clock API hopefully the code can be moved elsewhere. Try to
avoid getting DTs deployed relying on the 32kHz clock by removing it
from the bindings, grep seems to tell me it's not currently used anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This change makes it possible to set ramp_delay with 0.xxx mV/uS without
truncation issue.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix gpio number assignment, so that it can match the number stated in the comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Fix gpio number assignment, so that it can match the number stated in the comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
