| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6: (49 commits)
drivers/ide: Fix continuation line formats
ide: fixed section mismatch warning in cmd640.c
ide: ide_timing_compute() fixup
ide: make ide_get_best_pio_mode() static
via82cxxx: use ->pio_mode value to determine pair device speed
tx493xide: use ->pio_mode value to determine pair device speed
siimage: use ->pio_mode value to determine pair device speed
palm_bk3710: use ->pio_mode value to determine pair device speed
it821x: use ->pio_mode value to determine pair device speed
cs5536: use ->pio_mode value to determine pair device speed
cs5535: use ->pio_mode value to determine pair device speed
cmd64x: fix handling of address setup timings
amd74xx: use ->pio_mode value to determine pair device speed
alim15x3: fix handling of UDMA enable bit
alim15x3: fix handling of DMA timings
alim15x3: fix handling of command timings
alim15x3: fix handling of address setup timings
ide-timings: use ->pio_mode value to determine fastest PIO speed
ide: change ->set_dma_mode method parameters
ide: change ->set_pio_mode method parameters
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (28 commits)
ioat: cleanup ->timer_fn() and ->cleanup_fn() prototypes
ioat3: interrupt coalescing
ioat: close potential BUG_ON race in the descriptor cleanup path
ioat2: kill pending flag
ioat3: use ioat2_quiesce()
ioat3: cleanup, don't enable DCA completion writes
DMAENGINE: COH 901 318 lli sg offset fix
DMAENGINE: COH 901 318 configure channel direction
DMAENGINE: COH 901 318 remove irq counting
DMAENGINE: COH 901 318 descriptor pool refactoring
DMAENGINE: COH 901 318 cleanups
dma: Add MPC512x DMA driver
Debugging options for the DMA engine subsystem
iop-adma: redundant/wrong tests in iop_*_count()?
dmatest: fix handling of an even number of xor_sources
dmatest: correct raid6 PQ test
fsldma: Fix cookie issues
fsldma: Fix cookie issues
dma: cases IPU_PIX_FMT_BGRA32, BGR32 and ABGR32 are the same in ipu_ch_param_set_size()
dma: make Open Firmware device id constant
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: disable pcmcia ioctl for !ARM, prepare for removal
pcmcia: CodingStyle fixes
pcmcia: alchemy: fixup wrong comments
pcmcia: remove irq_list parameter from pd6729
yenta_socket: ENE CB712 CardBus bridge needs special treatment with Echo Audio Indigo soundcards
|
|
* document locking
* add the missing part of data structure invariants (relationship
between mnt_share and mnt_slave lists in case of a peer group
among slaves).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: add reader's lock for cno in nilfs_ioctl_sync
nilfs2: delete unnecessary condition in load_segment_summary
nilfs2: move iterator to write log into segment buffer
nilfs2: get rid of s_dirt flag use
nilfs2: get rid of nilfs_segctor_req struct
nilfs2: delete unnecessary condition in nilfs_dat_translate
nilfs2: fix potential hang in nilfs_error on errors=remount-ro
nilfs2: use mnt_want_write in ioctls where write access is needed
nilfs2: issue discard request after cleaning segments
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
x86: Fix out of order of gsi
x86: apic: Fix mismerge, add arch_probe_nr_irqs() again
x86, irq: Keep chip_data in create_irq_nr and destroy_irq
xen: Remove unnecessary arch specific xen irq functions.
smp: Use nr_cpus= to set nr_cpu_ids early
x86, irq: Remove arch_probe_nr_irqs
sparseirq: Use radix_tree instead of ptrs array
sparseirq: Change irq_desc_ptrs to static
init: Move radix_tree_init() early
irq: Remove unnecessary bootmem code
x86: Add iMac9,1 to pci_reboot_dmi_table
x86: Convert i8259_lock to raw_spinlock
x86: Convert nmi_lock to raw_spinlock
x86: Convert ioapic_lock and vector_lock to raw_spinlock
x86: Avoid race condition in pci_enable_msix()
x86: Fix SCI on IOAPIC != 0
x86, ia32_aout: do not kill argument mapping
x86, irq: Move __setup_vector_irq() before the first irq enable in cpu online path
x86, irq: Update the vector domain for legacy irqs handled by io-apic
x86, irq: Don't block IRQ0_VECTOR..IRQ15_VECTOR's on all cpu's
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (45 commits)
compal-laptop: Make it depend on CONFIG_RFKILL
classmate-laptop: Added some keys present in other devices
MAINTAINERS: Add git tree to x86 Platform Drivers
asus-acpi: remove duplicate comparison of asus_model strings
toshiba-acpi: fix multimedia keys on some machines
dell-laptop: Fix errors on failure and exit paths
dell-laptop: Fix build error by making buffer_mutex static
asus-laptop: fix style problems reported by checkpath.pl
asus-laptop: use device_create_file() instead of platform_group
asus-laptop: clean led code
asus-laptop: add gps rfkill
asus-laptop: set initial lcd state
asus-laptop: leds, remove dead code and fix asus_led_exit()/asus_led_init()
asus-laptop: add backlight changes notifications
asus-laptop: add bluetooth keys found on M9V
asus-laptop: switch to sparse keymap library
asus-laptop: rename wireless_status to wlan_status to avoid confusion
asus-laptop: add error check for write_acpi_int calls
asus-laptop: stop using ASUS_HANDLE and use relative methods instead
asus-laptop: rename function talking directly to acpi with asus_xxx scheme
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Document the message size limit
i2c-algo-pca: Drop duplicate variable
i2c: Hook up runtime PM support
i2c-parport-light: Add SMBus alert support
i2c-parport: Add SMBus alert support
i2c: Separate Kconfig option for i2c-smbus
i2c: Add SMBus alert support
i2c-parport: Give powered devices some time to settle
i2c-tiny-usb: Fix a comment on bus frequency
i2c-i801: Add Intel Cougar Point device IDs
i2c: Make PCI device ids constant
|
|
Fix docbook errors for x86 headers that were recently merged:
docproc: arch/x86/include/asm/atomic_32.h: No such file or directory
docproc: arch/x86/include/asm/io_32.h: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/ide-2.6
|
|
The PCMCIA ioctl -- deprecated for years -- suffers from insufficient
locking. As it already has been deprecated for years, with its removal
long overdue, limit it to !SMP and !PREEMPT.
Furthermore, the last legitimate use of the ioctl to be reported
relates to the ARM architecture in 2008.[1] Attempts to resolve
this issue turned out unsuccessful so far.[2] Other usages have only
been reported as hear-say. If there are any legitiate and necessary
use-cases remaining, please speak out before the end of the grace
period until 2.6.3{5,6}(-rc1).
[1] http://lists.infradead.org/pipermail/linux-pcmcia/2008-April/005440.html
see also: http://lkml.org/lkml/2008/2/27/291
[2] http://lists.infradead.org/pipermail/linux-pcmcia/2008-April/005450.html
http://lists.infradead.org/pipermail/linux-pcmcia/2010-January/006740.html
see also: http://lists.infradead.org/pipermail/linux-pcmcia/2008-April/005453.html
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Jaswinder Singh Rajput <jaswinder@kernel.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
devices and spectrometers
This patch removes the vstusb driver and support from the Linux tree.
This driver provided support for Vernier Software & Technology devices
and spectrometers (Ocean Optics). This driver is being replaced by a
user space - libusb - implementation.
Signed-off-by: Jim Collar <jim.collar@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1326) adds usb_enable_autosuspend() and
usb_disable_autosuspend() routines for use by drivers. If a driver
knows that its device can handle suspends and resumes correctly, it
can enable autosuspend all by itself. This is equivalent to the user
writing "auto" to the device's power/level attribute.
The implementation differs slightly from what it used to be. Now
autosuspend is disabled simply by doing usb_autoresume_device() (to
increment the usage counter) and enabled by doing
usb_autosuspend_device() (to decrement the usage counter).
The set_level() attribute method is updated to use the new routines,
and the USB Power-Management documentation is updated.
The patch adds a usb_enable_autosuspend() call to the hub driver's
probe routine, allowing the special-case code for hubs in quirks.c to
be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some devices which use mode switching revert to their
primary mode as they are reset. They must not be reset for
error handling. As user spaces makes the switch it also
has to tell the kernel that a device is quirky.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This has never worked properly because wsize passed to
cxacru_cm() is incorrectly set to the number of values
instead of the data bytes. The maximum number of values
that can be set at once is 7 which means the device will
not get enough data to work with and none of the
configuration values will be used.
At least one existing cxacru-cf.bin file contains invalid
data which will prevent the modem from syncing properly.
Fixing it is likely to break existing systems, and the
new sysfs interface for setting configuration parameters
can provide the same functionality. A script is provided
to convert from the original format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The modem can be configured using CM_REQUEST_CARD_DATA_SET,
although CM_REQUEST_CARD_DATA_GET does not return any data.
Tested by setting the modulation (0x0a) option.
There is a list of parameters in the following archive,
but the meaning of many of them is not well documented:
http://sourceforge.net/project/shownotes.php?release_id=301825
This source also indicates that the highest parameter set
is 0x4a but this varies by model so an arbitrary limit of
0x7f has been used (the index is a 32-bit integer).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When there is no connection, return an empty string
instead of "0" for the connection modulation.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
|
|
git://repo.or.cz/linux-2.6/linux-acpi-2.6/ibm-acpi-2.6 into x86-platform
|
|
i2c_master_send & i2c_master_recv do not support more than 64 kb
transfer, since msg.len is u16.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the SMBus alert mechanism to the i2c-parport-light
driver. The ADM1032 evaluation board at least is properly wired for
this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
|
|
Add support for the SMBus alert mechanism to the i2c-parport driver.
The ADM1032 evaluation board at least is properly wired for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
|
|
SMBus alert support. The SMBus alert protocol allows several SMBus
slave devices to share a single interrupt pin on the SMBus master,
while still allowing the master to know which slave triggered the
interrupt.
This is based on preliminary work by David Brownell. The key
difference between David's implementation and mine is that his was
part of i2c-core, while mine is split into a separate, standalone
module named i2c-smbus. The i2c-smbus module is meant to include
support for all SMBus extensions to the I2C protocol in the future.
The benefit of this approach is a zero cost for I2C bus segments which
do not need SMBus alert support. Where David's implementation
increased the size of struct i2c_adapter by 7% (40 bytes on i386),
mine doesn't touch it. Where David's implementation added over 150
lines of code to i2c-core (+10%), mine doesn't touch it. The only
change that touches all the users of the i2c subsystem is a new
callback in struct i2c_driver (common to both implementations.) I seem
to remember Trent was worried about the footprint of David'd
implementation, hopefully mine addresses the issue.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
|
|
Add the Intel Cougar Point (PCH) SMBus controller device IDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (62 commits)
Input: atkbd - release previously reserved keycodes 248 - 254
Input: add KEY_WPS_BUTTON definition
Input: ads7846 - add regulator support
Input: winbond-cir - fix suspend/resume
Input: gamecon - use pr_err() and friends
Input: gamecon - constify some of the setup structures
Input: gamecon - simplify pad type handling
Input: gamecon - simplify coordinate calculation for PSX
Input: gamecon - fix some formatting issues
Input: gamecon - add rumble support for N64 pads
Input: wacom - add device type to device name string
Input: s3c24xx_ts - report touch only when stylus is down
Input: s3c24xx_ts - re-enable IRQ on resume
Input: wacom - constify product features data
Input: wacom - use per-device instance of wacom_features
Input: sh_keysc - enable building on SH-Mobile ARM
Input: wacom - get features from driver info
Input: rotary-encoder - set gpio direction for each requested gpio
Input: sh_keysc - update the driver with mode 6
Input: sh_keysc - switch to using bitmaps
...
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
ARM: Eliminate decompressor -Dstatic= PIC hack
ARM: 5958/1: ARM: U300: fix inverted clk round rate
ARM: 5956/1: misplaced parentheses
ARM: 5955/1: ep93xx: move timer defines into core.c and document
ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
ARM: 5953/1: ep93xx: fix broken build of clock.c
ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
ARM: 5949/1: NUC900 add gpio virtual memory map
ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
ARM: make_coherent(): fix problems with highpte, part 2
MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
ARM: 5945/1: ep93xx: include correct irq.h in core.c
ARM: 5933/1: amba-pl011: support hardware flow control
ARM: 5930/1: Add PKMAP area description to memory.txt.
ARM: 5929/1: Add checks to detect overlap of memory regions.
ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
ARM: 5927/1: Make delimiters of DMA area globally visibly.
ARM: 5926/1: Add "Virtual kernel memory..." printout.
ARM: 5920/1: OMAP4: Enable L2 Cache
...
Fix up trivial conflict in arch/arm/mach-mx25/clock.c
|
|
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
|
|
|
|
|
|
|
|
|
|
Conflicts:
drivers/firmware/iscsi_ibft.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-numa-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: Remove configurable node size support for numa emulation
x86, numa: Add fixed node size option for numa emulation
x86, numa: Fix numa emulation calculation of big nodes
x86, acpi: Map hotadded cpu to correct node.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mm: Unify kernel_physical_mapping_init() API
x86, mm: Allow highmem user page tables to be disabled at boot time
x86: Do not reserve brk for DMI if it's not going to be used
x86: Convert tlbstate_lock to raw_spinlock
x86: Use the generic page_is_ram()
x86: Remove BIOS data range from e820
Move page_is_ram() declaration to mm.h
Generic page_is_ram: use __weak
resources: introduce generic page_is_ram()
|
|
|
|
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
sched: Fix SCHED_MC regression caused by change in sched cpu_power
sched: Don't use possibly stale sched_class
kthread, sched: Remove reference to kthread_create_on_cpu
sched: cpuacct: Use bigger percpu counter batch values for stats counters
percpu_counter: Make __percpu_counter_add an inline function on UP
sched: Remove member rt_se from struct rt_rq
sched: Change usage of rt_rq->rt_se to rt_rq->tg->rt_se[cpu]
sched: Remove unused update_shares_locked()
sched: Use for_each_bit
sched: Queue a deboosted task to the head of the RT prio queue
sched: Implement head queueing for sched_rt
sched: Extend enqueue_task to allow head queueing
sched: Remove USER_SCHED
sched: Fix the place where group powers are updated
sched: Assume *balance is valid
sched: Remove load_balance_newidle()
sched: Unify load_balance{,_newidle}()
sched: Add a lock break for PREEMPT=y
sched: Remove from fwd decls
sched: Remove rq_iterator from move_one_task
...
Fix up trivial conflicts in kernel/sched.c
|
|
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (172 commits)
perf_event, amd: Fix spinlock initialization
perf_event: Fix preempt warning in perf_clock()
perf tools: Flush maps on COMM events
perf_events, x86: Split PMU definitions into separate files
perf annotate: Handle samples not at objdump output addr boundaries
perf_events, x86: Remove superflous MSR writes
perf_events: Simplify code by removing cpu argument to hw_perf_group_sched_in()
perf_events, x86: AMD event scheduling
perf_events: Add new start/stop PMU callbacks
perf_events: Report the MMAP pgoff value in bytes
perf annotate: Defer allocating sym_priv->hist array
perf symbols: Improve debugging information about symtab origins
perf top: Use a macro instead of a constant variable
perf symbols: Check the right return variable
perf/scripts: Tag syscall_name helper as not yet available
perf/scripts: Add perf-trace-python Documentation
perf/scripts: Remove unnecessary PyTuple resizes
perf/scripts: Add syscall tracing scripts
perf/scripts: Add Python scripting engine
perf/scripts: Remove check-perf-trace from listed scripts
...
Fix trivial conflict in tools/perf/util/probe-event.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (28 commits)
ftrace: Add function names to dangling } in function graph tracer
tracing: Simplify memory recycle of trace_define_field
tracing: Remove unnecessary variable in print_graph_return
tracing: Fix typo of info text in trace_kprobe.c
tracing: Fix typo in prof_sysexit_enable()
tracing: Remove CONFIG_TRACE_POWER from kernel config
tracing: Fix ftrace_event_call alignment for use with gcc 4.5
ftrace: Remove memory barriers from NMI code when not needed
tracing/kprobes: Add short documentation for HAVE_REGS_AND_STACK_ACCESS_API
s390: Add pt_regs register and stack access API
tracing/kprobes: Make Kconfig dependencies generic
tracing: Unify arch_syscall_addr() implementations
tracing: Add notrace to TRACE_EVENT implementation functions
ftrace: Allow to remove a single function from function graph filter
tracing: Add correct/incorrect to sort keys for branch annotation output
tracing: Simplify test for function_graph tracing start point
tracing: Drop the tr check from the graph tracing path
tracing: Add stack dump to trace_printk if stacktrace option is set
tracing: Use appropriate perl constructs in recordmcount.pl
tracing: optimize recordmcount.pl for offsets-handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (44 commits)
rcu: Fix accelerated GPs for last non-dynticked CPU
rcu: Make non-RCU_PROVE_LOCKING rcu_read_lock_sched_held() understand boot
rcu: Fix accelerated grace periods for last non-dynticked CPU
rcu: Export rcu_scheduler_active
rcu: Make rcu_read_lock_sched_held() take boot time into account
rcu: Make lockdep_rcu_dereference() message less alarmist
sched, cgroups: Fix module export
rcu: Add RCU_CPU_STALL_VERBOSE to dump detailed per-task information
rcu: Fix rcutorture mod_timer argument to delay one jiffy
rcu: Fix deadlock in TREE_PREEMPT_RCU CPU stall detection
rcu: Convert to raw_spinlocks
rcu: Stop overflowing signed integers
rcu: Use canonical URL for Mathieu's dissertation
rcu: Accelerate grace period if last non-dynticked CPU
rcu: Fix citation of Mathieu's dissertation
rcu: Documentation update for CONFIG_PROVE_RCU
security: Apply lockdep-based checking to rcu_dereference() uses
idr: Apply lockdep-based diagnostics to rcu_dereference() uses
radix-tree: Disable RCU lockdep checking in radix tree
vfs: Abstract rcu_dereference_check for files-fdtable use
...
|
|
'tracing-fixes-for-linus', 'x86-debug-for-linus', 'x86-doc-for-linus', 'x86-gpu-for-linus' and 'x86-rlimit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
generic-ipi: Optimize accesses by using DEFINE_PER_CPU_SHARED_ALIGNED for IPI data
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
plist: Fix grammar mistake, and c-style mistake
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kprobes: Add mcount to the kprobes blacklist
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86_64: Print modules like i386 does
* 'x86-doc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Put 'nopat' in kernel-parameters
* 'x86-gpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64: Allow fbdev primary video code
* 'x86-rlimit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Use helpers for rlimits
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (35 commits)
[S390] time: remove unused code
[S390] zcore: Add prefix registers to dump header
[S390] correct vdso version string
[S390] add support for compressed kernels
[S390] Define new s390 ELF note sections in elf.h
[S390] codepage conversion of kernel parameter line
[S390] seq_file: convert drivers/s390/
[S390] add z9-ec/z10 instruction to kernel disassembler
[S390] dasd: correct offline processing
[S390] dasd: fix refcounting.
[S390] dasd: fix online/offline race
[S390] use kprobes_built_in() in mm/fault code
[S390] bug: use relative pointers in bug table entries
[S390] Cleanup struct _lowcore usage and defines.
[S390] free_initmem: reduce code duplication
[S390] Replace ENOTSUPP usage with EOPNOTSUPP
[S390] spinlock: check virtual cpu running status
[S390] sysinfo: fix SYSIB 3,2,2 structure
[S390] add MACHINE_IS_LPAR flag
[S390] qdio: optimize cache line usage of struct qdio_irq
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (49 commits)
pcmcia: validate late-added resources
pcmcia: allow for extension of resource interval
pcmcia: remove useless msleep in ds.c
pcmcia: use read_cis_mem return value
pcmcia: handle error in serial_cs config calls
pcmcia: add locking to pcmcia_{read,write}_cis_mem
pcmcia: avoid prod_id memleak
pcmcia: avoid sysfs-related lockup for cardbus
pcmcia: use state machine for extended requery
pcmcia: delay re-scanning and re-querying of PCMCIA bus
pcmcia: use pccardd to handle eject, insert, suspend and resume requests
pcmcia: use ops_mutex for rsrc_{mgr,nonstatic} locking
pcmcia: use mutex for dynid lock
pcmcia: assert locking to struct pcmcia_device
pcmcia: add locking documentation
pcmcia: simplify locking
pcmcia: add locking to struct pcmcia_socket->pcmcia_state()
pcmcia: protect s->device_count
pcmcia: properly lock skt->irq, skt->irq_mask
pcmcia: lock ops->set_socket
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
powerpc: Fix lwsync feature fixup vs. modules on 64-bit
powerpc: Convert pmc_owner_lock to raw_spinlock
powerpc: Convert die.lock to raw_spinlock
powerpc: Convert tlbivax_lock to raw_spinlock
powerpc: Convert mpic locks to raw_spinlock
powerpc: Convert pmac_pic_lock to raw_spinlock
powerpc: Convert big_irq_lock to raw_spinlock
powerpc: Convert feature_lock to raw_spinlock
powerpc: Convert i8259_lock to raw_spinlock
powerpc: Convert beat_htab_lock to raw_spinlock
powerpc: Convert confirm_error_lock to raw_spinlock
powerpc: Convert ipic_lock to raw_spinlock
powerpc: Convert native_tlbie_lock to raw_spinlock
powerpc: Convert beatic_irq_mask_lock to raw_spinlock
powerpc: Convert nv_lock to raw_spinlock
powerpc: Convert context_lock to raw_spinlock
powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
powerpc/86xx: Enable VME driver on the GE SBC610
powerpc/86xx: Enable VME driver on the GE PPC9A
powerpc/86xx: Add MSI section to GE PPC9A DTS
...
|
