| Age | Commit message (Collapse) | Author |
|---|
|
This ensures that the PMIC RTC provides the system time, rather than
the on-SoC RTC, which is not battery-backed.
tegra124-venice2.dts isn't touched yet since we haven't added any off-
SoC RTC device to its device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra20 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add properties common to all Tamonten-derived boards to the Tamonten
DTSI and add the fixed 1.05 V regulator.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Enabling the LP1 suspend mode for Tegra devices.
Tested-by: Marc Dietrich <marvin24@gmx.de> # paz00 board
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use the GIC and standard IRQ binding defines in all IRQ specifiers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch updates all Tegra board files so that they contain all the
properties required by the updated USB DT binding. Note that this patch
only adds the new properties and does not yet remove the old properties,
in order to maintain bisectability. The old properties will be removed
once the driver has been updated to assume the new bindings.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
[swarren: fixed some newly added regulator-name properties to better
match schematic, avoided duplicate regulator-name on Whistler.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Adding the bindings of the clock source of PMC in DT.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The GPIO pin of SD slot card detection should active low.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
No Tegra20 Platform is running PLL_P at another rate than 216MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Hook up the required regulators, I2C DDC adapter and hotplug detect GPIO
to the Tamonten HDMI output. Carrier boards still need to explicitly
enable the output to use it.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The Tamonten SOM has an ON Semiconductor NCT1008 connected to the DVC
bus which is used to measure the ambient (local) temperature as well as
the on-die (remote) temperature.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This commit allows the I2C2 controller on Tegra20 to be routed either to
the DDC or the PTA pin group at runtime. On Tamonten this allows the I2C
bus to be used for the DDC of the HDMI connector or to access I2C chips
on the carrier board.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Commit 13511de "regulator: deprecate regulator-compatible DT property"
now allows for simpler content within the regulators node within a PMIC.
Modify all the Tegra device tree files to take advantage of this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
The Tamonten is an NVIDIA Tegra2 based system-on-module (SOM) that is
designed to cover a broad range of applications.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
