| Age | Commit message (Collapse) | Author |
|---|
|
The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.
Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>
|
|
*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add twl4030-usb data node in twl4030 device tree file. twl4030-usb is the phy
driver for MUSB used in omap3 chipsets. The dt data is comprised of two
interrupts, one for ID and one for VBUS and three phandles to regulator.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add twl6030-usb data node in twl6030 device tree file. twl6030-usb is the
comparator driver for USB that detects VBUS and ID events. The dt data is
comprised of two interrupts, one for ID and one for VBUS and a phandle to the
regulator.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add AM335X EVM-SK device tree source (am335x-sk.dts) file to use
the am33xx.dtsi SoC file, along with the memory node information.
Also adds support for tps65910 regulator and lis331dlh accelerometer.
Following drivers/functionality were tested on AM335x-EVM-SK.
* I2C
* TPS65910 regulators
* lis331dlh accelerometer
AM335x EVM Starter Kit details can be accessed from:
http://www.ti.com/tool/tmdssk3358
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.
TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add Bosch D_CAN controller device tree data to AM33XX dtsi
file by adding d_can device nodes with all the necessary
parameters.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Adds basic pinctrl device tree data for AM33XX family of devices.
This patch is based on the pinctrl-single driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.
Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.
This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.
V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
configuration
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim <kgene.kim@samsung.com>:
One is spi stuff for fix the device names for the different subtypes of
the spi controller. And the other is adding missing .smp field for
exynos4-dt and fixing memory sections for exynos4210-trats board.
* 'v3.7-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Set .smp field of machine descriptor for exynos4-dt
ARM: dts: Split memory into 4 sections for exynos4210-trats
ARM: SAMSUNG: Add naming of s3c64xx-spi devices
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Timer fix for am33xx, runtime PM fix for UART, audio McBSP fixes,
mux and pinctrl fixes, and Beagle OPP fix.
* tag 'omap-for-v3.7-rc2/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
ARM: OMAP3: Beagle: fix OPP customization and initcall ordering
ARM: OMAP3: Fix 3430 legacy mux names for ssi1 signals.
ARM: OMAP2+: Fix location of select PINCTRL
ARM/dts: omap3: Fix mcbsp2/3 hwmods to be able to probe the drivers for audio
ARM: OMAP2: UART: fix console UART mismatched runtime PM status
ARM: OMAP3: PM: apply part of the erratum i582 workaround
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/ljones/linux-3.0-ux500 into fixes
* 'for-rcs-3.7' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From Nicolas Ferre <nicolas.ferre@atmel.com>:
A mix of typos and critical fixes.
The most important ones are a duplicated definition of a Kconfig
variable and the handling of external interrupts for non-DT case.
The new at91sam9g10 was suffering a recognition issue due to an ID
mis-interpreted: this was leading to a kernel panic.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91: (257 commits)
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The current DT nodes for mx23/mx28 miss the `clocks-names` item for gpmi-nand.
So the gpmi-nand driver could not find the proper clock.
This patch fixes this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Now the Nomadik I2C driver has been converted to an AMBA one, we
are required to provide the Primecell IDs via platform code. When
booting with DT enabled these have to be specified in the device
nodes. We do that here.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
|
|
Fixes the following errors:
[ 2.318084] omap-mcbsp 49022000.mcbsp: invalid rx DMA channel
[ 2.324432] omap-mcbsp 49024000.mcbsp: invalid rx DMA channel
Which is because we failed to link the sidetone hwmod for McBSP2/3. The
missing sidetone hwmod link will prevent omap_device_alloc() to append the
DMA resources since we - accidentally - end up having the same number of
resources provided from DT (IO/IRQ) as we have in hwmod for the McBSP ports
without the ST resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
- improve #ifdef logic to prevent linker errors with CACHE_FEROCEON_L2
- lsxl board dts fixes
* tag 'kirkwood_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix buttons on lsxl boards
ARM: kirkwood: fix LEDs names for lsxl boards
ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
|
|
Change event type to switch for the power and autopower switches.
Additionally, this patch aligns the keycodes with the other linkstation
boards already supported by linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Don't use the specific board name in a the common device tree include file.
Instead use the common name 'lsxl'.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
Misc. fixes for latest changes to mach-dove/
Fixes build breakage for mach-dove
* tag 'mvebu_dove_late_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux:
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
|
|
Make use of DT support for the crypto engine on dove and remove
the obsolete init call.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The watchdog on dove requires an interrupt that is not yet
available on DT. Therefore, the watchdog DT node is removed
until the corresponding chained intc is available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch adds proper ranges for all mapped addresses within
dove SoC and moves the interrupt controller node inside the simple-bus
node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
During the review process of dove DT patches, Tauros2 cache
init call was changed and DT support added. This patch fixes
the call to Tauros2 init and adds a DT node. Moreover, plat/irq.h
include was missing from mach-dove/common.c.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Since the maximum section size on mach-exynos is set to 256MiB, boards
with memory configuration defined using sections bigger than 256MiB will
fail to boot with a kernel panic.
This patch modifies the dts file of Samsung Trats board to define four
sections of 256MiB instead of two of 512MiB to fix the boot problem.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 9e3c0066 (ARM: dts: imx6q-arm2: add pinctrl for uart and enet)
defines NANDF_CS pins as gpio in 'hog', assuming these two pins are
always used by usdhc3 in gpio mode as card-detection and
write-protection on ARM2 board. But it's not true. These pins are
shared by usdhc3 and gpmi-nand. We should have the pins functional
for gpmi-nand when usdhc3 is disabled.
Move the pins out of 'hog', so that pins only work in gpio mode as CD
and WP when usdhc3 is enabled, and otherwise they are available for
gpmi-nand.
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
EHCI and UHCI devices in wm8505.dtsi should use IRQ 1 & 0
respectively - not 43 as used on newer models.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This makes sure that the ARM Integrator device trees get compiled
during build.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
|
|
Conflicts:
arch/arm/kernel/smp.c
|
|
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
|
|
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"Core:
- Add DT properties for card detection (broken-cd, cd-gpios,
non-removable)
- Don't poll non-removable devices
- Fixup/rework eMMC sleep mode/"power off notify" feature
- Support eMMC background operations (BKOPS). To set the one-time
programmable fuse that enables bkops on an eMMC that doesn't
already have it set, you can use the "mmc bkops enable" command in:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- atmel-mci, dw_mmc, pxa-mci, dove, s3c, spear: Add device tree
support
- bfin_sdh: Add support for the controller in bf60x
- dw_mmc: Support Samsung Exynos SoCs
- eSDHC: Add ADMA support
- sdhci: Support testing a cd-gpio (from slot-gpio) instead of
presence bit
- sdhci-pltfm: Support broken-cd DT property
- tegra: Convert to only supporting DT (mach-tegra has gone DT-only)"
* tag 'mmc-merge-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (67 commits)
mmc: core: Fixup broken suspend and eMMC4.5 power off notify
mmc: sdhci-spear: Add clk_{un}prepare() support
mmc: sdhci-spear: add device tree bindings
mmc: sdhci-s3c: Add clk_(enable/disable) in runtime suspend/resume
mmc: core: Replace MMC_CAP2_BROKEN_VOLTAGE with test for fixed regulator
mmc: sdhci-pxav3: Use sdhci_get_of_property for parsing DT quirks
mmc: dt: Support "broken-cd" property in sdhci-pltfm
mmc: sdhci-s3c: fix the wrong number of max bus clocks
mmc: sh-mmcif: avoid oops on spurious interrupts
mmc: sh-mmcif: properly handle MMC_WRITE_MULTIPLE_BLOCK completion IRQ
mmc: sdhci-s3c: Fix crash on module insertion for second time
mmc: sdhci-s3c: Enable only required bus clock
mmc: Revert "mmc: dw_mmc: Add check for IDMAC configuration"
mmc: mxcmmc: fix bug that may block a data transfer forever
mmc: omap_hsmmc: Pass on the suspend failure to the PM core
mmc: atmel-mci: AP700x PDC is not connected to MCI
mmc: atmel-mci: DMA can be used with other controllers
mmc: mmci: use clk_prepare_enable and clk_disable_unprepare
mmc: sdhci-s3c: Add device tree support
mmc: dw_mmc: add support for exynos specific implementation of dw-mshc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
This branch contains one counter locking fix and an
alignment fix. Other fixes are warning fixes, fixes
for return value checks.
I've also included removal of some extra semicolons,
dropping of some duplicate includes, and an a change
for wl12xx enumeration that are not strictly fixes
but would be good to get out of the way for -rc1.
* tag 'omap-for-v3.7-rc1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
AM35xx: Add missing hwmod entry for the HDQ/1-Wire present in AM3505/3517 CPUs.
ARM: OMAP2+: gpmc: annotate exit sections properly
ARM: OMAP: fix return value check in realtime_counter_init()
ARM: OMAP: hsmmc: fix return value check in omap_hsmmc_init_one()
OMAPDSS: fix return value check in create_dss_pdev()
ARM: OMAP2+: Add am335x evm and bone targets to common Makefile
arm: increase FORCE_MAX_ZONEORDER for TI AM33XX
ARM: OMAP: OMAP_DEBUG_LEDS needs to select LEDS_CLASS
ARM: OMAP: rx51: Fix a section mismatch warn
ARM: OMAP2+: Round of the carve out memory requested to section_size
ARM: OMAP: counter: add locking to read_persistent_clock
|
|
Sometimes we want the kernel build process to only print messages
on errors, e.g. in automated build testing. This uses the "kecho"
macro that the build system provides to hide a few informational
messages. Nothing changes for a regular "make" or "make V=1".
Without this patch, building any ARM kernel results in:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
|
|
git://git.infradead.org/users/dhowells/linux-headers
UAPI Disintegration 2012-10-09
Conflicts:
MAINTAINERS
arch/arm/configs/bcmring_defconfig
arch/arm/mach-imx/clk-imx51-imx53.c
drivers/mtd/nand/Kconfig
drivers/mtd/nand/bcm_umi_nand.c
drivers/mtd/nand/nand_bcm_umi.h
drivers/mtd/nand/orion_nand.c
|
|
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron), McPDM, DMIC, McBSP1 and McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These all use the generic pinctrl-single driver for the padconf registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
u-boot stopped configuring 'non essential' pins recently. The kernel needs
to configure the mux for audio needs.
Since the pinmux for these IPs are static let pinctrl to handle the mux
configuration for.
Configuring the mux for: twl6040 (audpwron, irq), McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
McBSP3 is not usable on OMAP4 SDP/Blaze (the pins used for McPDM).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
