| Age | Commit message (Collapse) | Author |
|---|
|
The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. On the
Qualcomm Snapdragon S4/Krait architecture CPUs the processor continues
to consider the IT state bits while in ARM mode. This makes it so
that some instructions are skipped by the CPU.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[rmk+kernel@arm.linux.org.uk: fixed whitespace formatting in patch]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The exception handling code fails to clear the IT state, potentially
leading to incorrect execution of the fixup if the size of the IT
block is more than one.
Let fixup_exception do the IT sanitizing if a fixup has been found,
and restore CPSR from the stack when returning from a data abort.
Cc: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.baserock.org/delta/linux into devel-stable
Conflicts:
arch/arm/kernel/head.S
This series has been well tested and it would be great to get this
merged now.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Use CONFIG_ARCH_PHYS_ADDR_T_64BIT to determine
if ignoring or truncating of memory banks is
neccessary. This may be needed in the case of
64-bit memory bank addresses but when phys_addr_t
is kept 32-bit.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The DTB and/or the kernel command line may pass
64-bit addresses regardless of kernel configuration,
so update arm_add_memory() to take 64-bit arguments
independently of the phys_addr_t size.
This allows non-wrapping handling of high memory
banks such as the second memory bank of APE6EVM
(at 0x2_0000_0000) in case of 32-bit phys_addr_t.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is the ARM part of Christoph's patchset cleaning up the various
uses of __get_cpu_var across the tree.
The idea is to convert __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations
that use the offset. Thereby address calculations are avoided and fewer
registers are used when code is generated.
[will: fixed debug ref counting checks and pcpu array accesses]
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The work-around for A15 errata 798181 is not needed if appropriate ECO
fixes have been applied to r3p2 and earlier core revisions. This can be
checked by reading REVIDR register bits 4 and 9. If only bit 4 is set,
then the IPI broadcast can be skipped.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
keyword
Commit 'f52bb722547f43caeaecbcc62db9f3c3b80ead9b'
Author: Sricharan R <r.sricharan@ti.com>
ARM: mm: Correct virt_to_phys patching for 64 bit physical addresses
introduced a __ARMEB__ macro usage in a new place, but missed the second
underscore. So correcting it here.
Also a explicit .align keyword is needed for the label with .long
data-type to be aligned on the 4 byte boundary. Otherwise this can
cause problem for thumb2 build. So adding it here.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into devel-stable
|
|
In case of BE8 kernel data is in BE order whereas code stays in LE
order. Move sigreturn_codes to separate .S file and use proper
assembler mnemonics for these code snippets. In this case compiler
will take care of proper instructions byteswaps for BE8 case.
Change assumes that sufficiently Thumb-capable tools are used to
build kernel.
Problem was discovered during ltp testing of BE system: all rt_sig*
tests failed. Tested against the same tests in both BE and LE modes.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
|
|
Currently BUG() uses .word or .hword to create the necessary illegal
instructions. However if we are building BE8 then these get swapped
by the linker into different illegal instructions in the text. This
means that the BUG() macro does not get trapped properly.
Change to using <asm/opcodes.h> to provide the necessary ARM instruction
building as we cannot rely on gcc/gas having the `.inst` instructions
which where added to try and resolve this issue (reported by Dave Martin
<Dave.Martin@arm.com>).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
|
|
When in BE8 mode, our instructions are not in the same ordering as the
data, so use <asm/opcodes.h> to take this into account.
Note, also requires modules to be built --be8
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
|
|
The trap handler needs to take into account the endian configuration of
the system when loading instructions. Use <asm/opcodes.h> to provide the
necessary conversion functions.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
The smp_scu driver needs to use the relaxed readl/write accessors
to avoid any issues with the endian mode the processor core is in.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
|
|
Ensure the twd driver uses the correct calls to access the hardware
to ensure that we do not end up with data in the wrong endian format.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
|
|
If we are booting in LE and compiled for BE8, then add code to
set the state to bE8. Since the instruction stream is always LE,
we do not need to do anything special to the instruction.
Also ensure that the secondary processors are started in the same mode.
Note, we do add about 20 bytes to the kernel image, but it seems easier
to do this than adding another configuration to change.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
The fixup_pv_table assumes that the instructions are in the same
endian configuration as the data, but when the CPU is running in
BE8 the instructions stay in little-endian format.
Make sure if CONFIG_CPU_ENDIAN_BE8 is set that we do all the
alterations to the instructions taking in to account the LDR/STR
will be swapping the data endian-ness.
Since the code is only modifying a byte, we avoid dual-swapping
the data, and just change the bits we clear and ORR in (in the
case where the code is not thumb2).
For thumb2, we add the necessary rev16 instructions to ensure that
the instructions are processed in the correct format, as it was
easier than re-writing the code to contain a mask and shift.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
Add ARM_BE8() helper to wrap any code conditional on being
compile when CONFIG_ARM_ENDIAN_BE8 is selected and convert
existing places where this is to use it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into devel-stable
This series extends the existing ARM v2p runtime patching for 64 bit.
Needed for LPAE machines which have physical memory beyond 4GB.
|
|
Pull ARM fixes from Russell King:
"Some more ARM fixes, nothing particularly major here. The biggest
change is to fix the SMP_ON_UP code so that it works with TI's Aegis
cores"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7851/1: check for number of arguments in syscall_get/set_arguments()
ARM: 7846/1: Update SMP_ON_UP code to detect A9MPCore with 1 CPU devices
ARM: 7845/1: sharpsl_param.c: fix invalid memory access for pxa devices
ARM: 7843/1: drop asm/types.h from generic-y
ARM: 7842/1: MCPM: don't explode if invoked without being initialized first
|
|
This patch adds a step in the init sequence, in order to recreate
the kernel code/data page table mappings prior to full paging
initialization. This is necessary on LPAE systems that run out of
a physical address space outside the 4G limit. On these systems,
this implementation provides a machine descriptor hook that allows
the PHYS_OFFSET to be overridden in a machine specific fashion.
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The current phys_to_virt patching mechanism works only for 32 bit
physical addresses and this patch extends the idea for 64bit physical
addresses.
The 64bit v2p patching mechanism patches the higher 8 bits of physical
address with a constant using 'mov' instruction and lower 32bits are patched
using 'add'. While this is correct, in those platforms where the lowmem addressable
physical memory spawns across 4GB boundary, a carry bit can be produced as a
result of addition of lower 32bits. This has to be taken in to account and added
in to the upper. The patched __pv_offset and va are added in lower 32bits, where
__pv_offset can be in two's complement form when PA_START < VA_START and that can
result in a false carry bit.
e.g
1) PA = 0x80000000; VA = 0xC0000000
__pv_offset = PA - VA = 0xC0000000 (2's complement)
2) PA = 0x2 80000000; VA = 0xC000000
__pv_offset = PA - VA = 0x1 C0000000
So adding __pv_offset + VA should never result in a true overflow for (1).
So in order to differentiate between a true carry, a __pv_offset is extended
to 64bit and the upper 32bits will have 0xffffffff if __pv_offset is
2's complement. So 'mvn #0' is inserted instead of 'mov' while patching
for the same reason. Since mov, add, sub instruction are to patched
with different constants inside the same stub, the rotation field
of the opcode is using to differentiate between them.
So the above examples for v2p translation becomes for VA=0xC0000000,
1) PA[63:32] = 0xffffffff
PA[31:0] = VA + 0xC0000000 --> results in a carry
PA[63:32] = PA[63:32] + carry
PA[63:0] = 0x0 80000000
2) PA[63:32] = 0x1
PA[31:0] = VA + 0xC0000000 --> results in a carry
PA[63:32] = PA[63:32] + carry
PA[63:0] = 0x2 80000000
The above ideas were suggested by Nicolas Pitre <nico@linaro.org> as
part of the review of first and second versions of the subject patch.
There is no corresponding change on the phys_to_virt() side, because
computations on the upper 32-bits would be discarded anyway.
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
On some PAE systems (e.g. TI Keystone), memory is above the
32-bit addressable limit, and the interconnect provides an
aliased view of parts of physical memory in the 32-bit addressable
space. This alias is strictly for boot time usage, and is not
otherwise usable because of coherency limitations. On such systems,
the idmap mechanism needs to take this aliased mapping into account.
This patch introduces virt_to_idmap() and a arch function pointer which
can be populated by platform which needs it. Also populate necessary
idmap spots with now available virt_to_idmap(). Avoided #ifdef approach
to be compatible with multi-platform builds.
Most architecture won't touch it and in that case virt_to_idmap()
fall-back to existing virt_to_phys() macro.
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
git://git.linaro.org/people/jstultz/linux into timers/core
Pull more timekeeping items for v3.13 from John Stultz:
* Small cleanup in the clocksource code.
* Fix for rtc-pl031 to let it work with alarmtimers.
* Move arm64 to using the generic sched_clock framework & resulting
cleanup in the generic sched_clock code.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Convert arm to use the common of_flat_dt_match_machine function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
|
|
Register with the generic sched_clock framework now that it
supports 64 bits. This fixes two problems with the current
sched_clock support for machines using the architected timers.
First off, we don't subtract the start value from subsequent
sched_clock calls so we can potentially start off with
sched_clock returning gigantic numbers. Second, there is no
support for suspend/resume handling so problems such as discussed
in 6a4dae5 (ARM: 7565/1: sched: stop sched_clock() during
suspend, 2012-10-23) can happen without this patch. Finally, it
allows us to move the sched_clock setup into drivers clocksource
out of the arch ports.
Cc: Christopher Covington <cov@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Convert arm to use new early_init_dt_scan function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
|
|
Since software events can always be scheduled, perf allows software and
hardware events to be mixed together in the same event group. There are
two ways in which this can come about:
(1) A SW event is added to a HW group. This validates using the HW PMU
of the group leader.
(2) A HW event is added to a SW group. This inserts the SW events and
the new HW event into a HW context, but the SW event remains the
group leader.
When validating the latter case, we would ideally compare the PMU of
each event in the group with the relevant HW PMU. The problem is, in the
face of potentially multiple HW PMUs, we don't have a handle on the
relevant structure. Commit 7b9f72c62ed0 ("ARM: perf: clean up event
group validation") attempting to resolve this issue, but actually made
things *worse* by comparing with the leader PMU. If the leader is a SW
event, then we automatically `pass' all the HW events during validation!
This patch removes the check against the leader PMU. Whilst this will
allow events from multiple HW PMUs to be grouped together, that should
probably be dealt with in perf core as the result of a later patch.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.linaro.org/people/ardbiesheuvel/linux-arm into devel-stable
|
|
clockevents/3.13
Adds support to configure the rate and enable the event stream for architected
timer. The event streams can be used to impose a timeout on a wfe, to safeguard
against any programming error in case an expected event is not generated or
even to implement wfe-based timeouts for userspace locking implementations.
This feature can be disabled(enabled by default).
Since the timer control register is reset to zero on warm boot, CPU PM notifier
is added to save and restore the value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The generic code is well equipped to differentiate between
SMP and UP configurations.However, there are some devices which
use Cortex-A9 MP core IP with 1 CPU as configuration. To let
these SOCs to co-exist in a CONFIG_SMP=y build by leveraging
the SMP_ON_UP support, we need to additionally check the
number the cores in Cortex-A9 MPCore configuration. Without
such a check in place, the startup code tries to execute
ALT_SMP() set of instructions which lead to CPU faults.
The issue was spotted on TI's Aegis device and this patch
makes now the device work with omap2plus_defconfig which
enables SMP by default. The change is kept limited to only
Cortex-A9 MPCore detection code.
Note that if any future SoC *does* use 0x0 as the PERIPH_BASE, then
the SCU address check code needs to be #ifdef'd for for the Aegis
platform.
Acked-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now that gic_secondary_init is no longer needed to be called by SMP init
functions, the header is not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
This patch implements the functions required for the perf registers API,
allowing the perf tool to interface kernel register dumps with libunwind
in order to provide userspace backtracing.
Cc: Jean Pihet <jean.pihet@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Most DT ARM machs require common clock providers initialized before timers.
Currently, arch/arm machs use .init_time to call of_clk_init right before
clocksource_of_init. This prevents to remove that callback and use the default
one instead.
This patch adds a call to of_clk_init() to the default .init_time callback
for COMMON_CLK enabled machs to allow to remove custom callbacks where applicable.
While at it, also reorder includes alphabetically.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
|
|
ad65782fba50 (context_tracking: Optimize main APIs off case
with static key) converted context tracking main APIs to inline
function and left ARM asm callers behind.
This can be easily fixed by making ARM calling the post static
keys context tracking function. We just need to replicate the
static key checks there. We'll remove these later when ARM will
support the context tracking static keys.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Anil Kumar <anilk4.v@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@linaro.org>
|
|
This patch adds support for configuring the event stream frequency
and enabling it.
It also adds the hwcaps definitions to the user to detect this event
stream feature.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
|
|
We need a mechanism to let an inbound CPU signal that it is alive before
even getting into the kernel environment i.e. from early assembly code.
Using an IPI is the simplest way to achieve that.
This adds some basic infrastructure to register a struct completion
pointer to be "completed" when the dedicated IPI for this task is
received.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
|
|
Commit 377747c40657 ("ARM: entry: allow ARM-private syscalls to be
restarted") reworked the low-level syscall dispatcher to allow
restarting of ARM-private syscalls. Unfortunately, this relocated the
label used to dispatch a private syscall from the trace path, so that
the invocation would be bypassed altogether!
This causes applications to fail under strace as soon as they rely on
a private syscall (e.g. set_tls):
set_tls(0xb6fad4c0, 0xb6fadb98, 0xb6fb1050, 0xb6fad4c0, 0xb6fb1050)
= -1 ENOSYS (Function not implemented)
This patch fixes the label so that we correctly dispatch private
syscalls from the trace path.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
devel-stable
Nicolas Pitre writes:
This is the first part of the patch series adding IKS (In-Kernel
Switcher) support for big.LITTLE system architectures. This consists of
the core patches only. Extra patches to come later will introduce
various optimizations and tracing support.
Those patches were posted on the list a while ago here:
http://news.gmane.org/group/gmane.linux.ports.arm.kernel/thread=253942
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
|
|
Pull ARM updates from Russell King:
"This set includes adding support for Neon acceleration of RAID6 XOR
code from Ard Biesheuvel, cache flushing and barrier updates from Will
Deacon, and a cleanup to the ARM debug code which reduces the amount
of code by about 500 lines.
A few other cleanups, such as constifying the machine descriptors
which already shouldn't be written to, cleaning up the printing of the
L2 cache size"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (55 commits)
ARM: 7826/1: debug: support debug ll on hisilicon soc
ARM: 7830/1: delay: don't bother reporting bogomips in /proc/cpuinfo
ARM: 7829/1: Add ".text.unlikely" and ".text.hot" to arm unwind tables
ARM: 7828/1: ARMv7-M: implement restart routine common to all v7-M machines
ARM: 7827/1: highbank: fix debug uart virtual address for LPAE
ARM: 7823/1: errata: workaround Cortex-A15 erratum 773022
ARM: 7806/1: allow DEBUG_UNCOMPRESS for Tegra
ARM: 7793/1: debug: use generic option for ep93xx PL10x debug port
ARM: debug: move SPEAr debug to generic PL01x code
ARM: debug: move davinci debug to generic 8250 code
ARM: debug: move keystone debug to generic 8250 code
ARM: debug: remove DEBUG_ROCKCHIP_UART
ARM: debug: provide generic option choices for 8250 and PL01x ports
ARM: debug: move PL01X debug include into arch/arm/include/debug/
ARM: debug: provide PL01x debug uart phys/virt address configuration options
ARM: debug: add support for word accesses to debug/8250.S
ARM: debug: move 8250 debug include into arch/arm/include/debug/
ARM: debug: provide 8250 debug uart phys/virt address configuration options
ARM: debug: provide 8250 debug uart register shift configuration option
ARM: debug: provide 8250 debug uart flow control configuration option
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
Now that we support a timer-backed delay loop, I'm quickly getting sick
and tired of people complaining that their beloved bogomips value has
decreased. You know who you are!
This patch removes the bogomips line from /proc/cpuinfo, based on the
reasoning that any program parsing this is already broken and, as such,
won't be further broken if the field is removed.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It appears that gcc may put some code in ".text.unlikely" or
".text.hot" sections. Right now those aren't accounted for in unwind
tables. Add them.
I found some docs about this at:
http://gcc.gnu.org/onlinedocs/gcc-4.6.2/gcc.pdf
Without this, if you have slub_debug turned on, you can get messages
that look like this:
unwind: Index not found 7f008c50
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The newly introduced function is to be used as .restart callback for
ARMv7-M machines. The used register is architecturally defined, so it
should work for all M-class machines.
Acked-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
