| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: typo, nodes in address ascending order, shrink cmdline]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch adds the following Kconfig options to prepare the transition to
common clk framework:
- AT91_USE_OLD_CLK: this option is selected by every SoC which does not
support new at91 clks based on common clk framework (SoC which does not
define the clock tree in its device tree).
This options is also selected when the user choose non dt boards support
(new at91 clks can only be registered from a device tree definition).
- COMMON_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 3 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* device tree support is enabled
* the old at91 clk implementation is disabled (every selected SoC define
its clks in its device tree and non dt boards support is disabled)
- OLD_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 2 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* at least one of the selected SoCs does not define its clks in its
device tree or non dt-boards support is enabled
This patch selects AT91_USE_OLD_CLK in all currently supported SoCs. These
selects will be removed after clk definitions are properly added in each
soc's device tree.
It also selects AT91_USE_OLD_CLK in all non-dt boards support.
AT91_PMC_UNIT references are replaced by OLD_CLK_AT91, because PMC Unit is
enabled for both old and common clk implementations, and old clk
implementation should not be compiled if COMMON_CLK is enabled.
To avoid future link errors, a new stub is created for at91_dt_clock_init
function if OLD_CLK_AT91 is disabled.
A new check is added in dt init functions (setup.c) to prepare for SoCs
supporting new clk implementation. These SoCs won't setup the
register_clocks callback (clk registration is done using of_clk_init).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A first set of batches of fixes for 3.13. The diffstat is large
mostly because we're adding a defconfig for a family that's been
lacking it, and there's some missing clock information added for i.MX
and OMAP.
The at91 new code is around dealing with RTC/RTT reset at boot to fix
possible hangs due to pending wakeup interrupts coming in during early
boot"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: OMAP2+: Fix build for dra7xx without omap4 and 5
ARM: OMAP2+: omap_device: maintain sane runtime pm status around suspend/resume
doc: devicetree: Add bindings documentation for omap-des driver
ARM: dts: doc: Document missing compatible property for omap-sham driver
ARM: OMAP3: Beagle: fix return value check in beagle_opp_init()
ARM: at91: fix hanged boot due to early rtt-interrupt
ARM: at91: fix hanged boot due to early rtc-interrupt
video: exynos_mipi_dsim: Remove unused variable
ARM: highbank: only select errata 764369 if SMP
ARM: sti: only select errata 764369 if SMP
ARM: tegra: init fuse before setting reset handler
ARM: vt8500: add defconfig for v6/v7 chips
ARM: integrator_cp: Set LCD{0,1} enable lines when turning on CLCD
ARM: OMAP: devicetree: fix SPI node compatible property syntax items
pinctrl: single: call pcs_soc->rearm() whenever IRQ mask is changed
ARM: OMAP2+: smsc911x: fix return value check in gpmc_smsc911x_init()
MAINTAINERS: drop discontinued mailing list
ARM: dts: i.MX51: Fix OTG PHY clock
ARM: imx: set up pllv3 POWER and BYPASS sequentially
ARM: imx: pllv3 needs relock in .set_rate() call
...
|
|
Make sure the RTC-interrupts are masked at boot by adding a new helper
function to be used at SOC-init.
This fixes hanged boot on all AT91 SOCs with an RTC (but RM9200), for
example, after a reset during an RTC-update or if an RTC-alarm goes off
after shutdown (e.g. when using RTC wakeup).
The RTC and RTT-peripherals are powered by backup power (VDDBU) (on all
AT91 SOCs but RM9200) and are not reset on wake-up, user, watchdog or
software reset. This means that their interrupts may be enabled during
early boot if, for example, they where not disabled during a previous
shutdown (e.g. due to a buggy driver or a non-clean shutdown such as a
user reset). Furthermore, an RTC or RTT-alarm may also be active.
The RTC and RTT-interrupts use the shared system-interrupt line, which
is also used by the PIT, and if an interrupt occurs before a handler
(e.g. RTC-driver) has been installed this leads to the system interrupt
being disabled and prevents the system from booting.
Note that when boot hangs due to an early RTC or RTT-interrupt, the only
way to get the system to start again is to remove the backup power (e.g.
battery) or to disable the interrupt manually from the bootloader. In
particular, a user reset is not sufficient.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org # 3.11.x
|
|
As the cpuidle driver code has no more the dependency with the pm code, the
'standby' callback being passed as a parameter to the device's platform data,
we can move the cpuidle driver in the drivers/cpuidle directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
drivers/cpuidle/Kconfig.arm
drivers/cpuidle/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
|
|
This board is impossible to found anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
as now we have full DT support of those board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Merge 9g20 with 9260 and 9g10 with 9261 as those SoCs can run from the same
kernel even in non DT world.
Fix the sam9261ek to allow 9g10 and sam9261 to compile together.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch introduces the SAMA5 support and a generic board file for SAMA5
devices. It also updates the PMC driver to manage clock division which is a
requirement since some peripherals can't work at the bus frequency on SAMA5.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
No more associate at91sam926x_time.c compilation with SOC_AT91SAM9 entry since
SAMA5D3 devices will use this driver too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Rename the board-rm9200-dt.c file so that we follow the pattern for
Device Tree board files: board-dt-<name of SoC sharing same core>.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
We will produce a board-dt file per SoC core type. That will ease code
readability and will prevent from including superfluous code for supporting
machines that will never be compiled together (particularly the ARM9 and C-A5
upcoming SoCs).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: modify commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The board is not available anymore and it seems its use
is very limited.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <abelloni@adeneo-embedded.com>
|
|
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
We can now compile all SoC core support together and DT boards.
We still can not compile together the non DT board.
So We keep the ARCH_AT91xxx for the non DT board and for backward defconfig
compatibility. This will enable the plaform_device ressources.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This will allow to simplify the switch to multi soc in the same kernel.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add these SMC accessors to the at91sam9x5 as we will need them for
NAND flash (for instance).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Kconfig and Makefile entries for SAM9x5 family.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Following removal announce and addition to feature-removal-schedule.txt,
here is the actual source code deletion for Atmel CAP9 family.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
As on the other sam9 we need to cleanly shutdown the DDRAM before rebooting.
On those SoC the SDRAM/DDRAM controller is different. So, the assembly code
ends up being not cleanly combined with previous at91sam9_alt_restart function.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
reset
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
|
|
Create a new device tree source file for Atmel at91sam9g45 SoC family.
The Evaluation Kit at91sam9m10g45ek includes it.
This first basic support will be populated as drivers and boards will be
converted to device tree.
Contains serial, dma and interrupt controllers.
The generic board file still takes advantage of platform data for early serial
init. As we need a storage media and the NAND flash driver is not converted to
DT yet, we keep old initialization for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
|
|
Add support for Calao USB-A9G20 boards. It will be integrated in
existing support for board of same form factor using at91sam9260 or
at91sam9263.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Merge boards together as they are barely the same.
Signed-off-by: Nico Erfurth <ne@erfurth.eu>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: updated to new machine_desc structure]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
|
|
This adds support for the RSI EWS machine (at91rm9200-based),
machine type 1609.
Includes fixes as suggested by Uwe Kleine-König and
cleanups as suggested by Russell and R.Schwebel.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
[nicolas.ferre@atmel.com: simplify board file header, move to at91_init_irq_default]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
no-one use it and it's nearly impossible get a board to work on it
and the Mainline implementation was never finished
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
|
|
The GS_IA18_S (GMS) is a carrier board from GeoSIG Ltd used with the
Stamp9G20 SoM from Taskit company.
It operate as an internet accelerometer.
Signed-off-by: Igor Plyatov <plyatov@gmail.com>
[nicolas.ferre@atmel.com: rm Kconfig, whitespace fixes, change machine name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Sergio Tanzilli <tanzilli@acmesystems.it>
[nicolas.ferre@atmel.com: whitespace fixes, change machine name]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
|
|
Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.
For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().
Rename at91sam9g20_reset.S to generalize to several chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system
Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
|
|
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.
The other boards revision will be specified via system_rev.
for 9g45ekes, m10g45ekes and m10g45ek boards and revisions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch adds support for Flexibity Connect platform from
http://www.flexibity.com/ (AT91SAM9260 based).
Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for Bluewater Systems Snapper 9260/9G20 modules
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/include/asm/system.h
arch/arm/mm/Kconfig
|
|
Both boards share the same board file, as the PortuxG20 is basically an
SBC based on the Stamp9G20.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for the Atmel AT572D940HF-EK board (development board for
the AT572D940HF processor).
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add support for the Atmel AT572D940HF processor (DIOPSIS range).
This processor integrates an ARM926 core, a DSP and the SoC
peripherals usually found on an AT91 processor (USART, SSC, SPI, TWI,
CAN, etc)
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
CONFIG_MACH_ECO920 is enabled in at91rm9200dk_defconfig. The name is
wrong, but this is better than adding another defconfig or don't get
compile coverage at all.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the support for cpuidle on AT91 SoCs, taken from the
cpuidle support in mach-kirkwood.
cpuidle needs sdram_selfrefresh_enable and _disable, so move their
definition to a separate header file instead of duplicating the code
already used in pm.c.
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
