summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-mx5/mm.c
AgeCommit message (Collapse)Author
2011-11-16ARM i.MX: Merge i.MX5 support into mach-imxSascha Hauer
This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx and adjusts the Makefile/Kconfig entries in a way that it's possible to compile i.MX5 together with i.MX3/6. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Shawn Guo <shawn.guo@linaro.org> Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
2011-10-04Merge branches 'cleanups/mx3-mm-v2' and 'cleanups/mxs' into imx-cleanupSascha Hauer
2011-10-04arm/imx: remove cpu_is_xxx() from arch_idle()Shawn Guo
This patch adds an idle hook imx_idle to be called in arch_idle(). Any soc that needs a customized idle implementation other than cpu_do_idle() can set up this hook in soc specific call. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-09-20Merge branches 'cleanups/assorted' and 'cleanups/mm-tzic' into imx-cleanupSascha Hauer
Conflicts: arch/arm/mach-mx5/Makefile Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-09-20ARM: mx5/mm: consolidate TZIC map codeJason Liu
Use a static mapping for TZIC to get rid of the duplicated code for ioremap and the corresponding error handling. This is already done on i.MX50. This patch also removes TZIC mapping for i.mx51 TO1 since there is no support for TO1 now since the following commit: 9ab4650 (ARM: imx: Get the silicon version from the IIM module) Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-09-20ARM: mx5/mm: Remove MX51_DEBUG related mappingJason Liu
MX51_DEBUG related mapping is dead code, no-one uses it Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-09-20ARM: mx5/mm: move i.MX50 mm stuff into mm.cJason Liu
i.MX50 is similar enough to i.MX51/53 to handle it in a single file. No functional change. Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-08-01ARM: mx5: fix remaining inconsistent names for irqsUwe Kleine-König
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2011-07-27dmaengine: imx-sdma: use platform_device_id to identify sdma versionShawn Guo
It might be not good to use software defined version to identify sdma device type, when hardware does not define such version. Instead, soc name is stable enough to define the device type. The patch uses platform_device_id rather than version number passed by platform data to identify sdma device type/version. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Vinod Koul <vinod.koul@intel.com>
2011-07-26Merge branch 'next/devel' of ↵Linus Torvalds
ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc * 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (128 commits) ARM: S5P64X0: External Interrupt Support ARM: EXYNOS4: Enable MFC on Samsung NURI ARM: EXYNOS4: Enable MFC on universal_c210 ARM: S5PV210: Enable MFC on Goni ARM: S5P: Add support for MFC device ARM: EXYNOS4: Add support FIMD on SMDKC210 ARM: EXYNOS4: Add platform device and helper functions for FIMD ARM: EXYNOS4: Add resource definition for FIMD ARM: EXYNOS4: Change devname for FIMD clkdev ARM: SAMSUNG: Add IRQ_I2S0 definition ARM: SAMSUNG: Add platform device for idma ARM: EXYNOS4: Add more registers to be saved and restored for PM ARM: EXYNOS4: Add more register addresses of CMU ARM: EXYNOS4: Add platform device for dwmci driver ARM: EXYNOS4: configure rtc-s3c on NURI ARM: EXYNOS4: configure MAX8903 secondary charger on NURI ARM: EXYNOS4: configure ADC on NURI ARM: EXYNOS4: configure MAX17042 fuel gauge on NURI ARM: EXYNOS4: configure regulators and PMIC(MAX8997) on NURI ARM: EXYNOS4: Increase NR_IRQS for devices with more IRQs ... Fix up tons of silly conflicts: - arch/arm/mach-davinci/include/mach/psc.h - arch/arm/mach-exynos4/Kconfig - arch/arm/mach-exynos4/mach-smdkc210.c - arch/arm/mach-exynos4/pm.c - arch/arm/mach-imx/mm-imx1.c - arch/arm/mach-imx/mm-imx21.c - arch/arm/mach-imx/mm-imx25.c - arch/arm/mach-imx/mm-imx27.c - arch/arm/mach-imx/mm-imx31.c - arch/arm/mach-imx/mm-imx35.c - arch/arm/mach-mx5/mm.c - arch/arm/mach-s5pv210/mach-goni.c - arch/arm/mm/Kconfig
2011-07-08gpio/mxc: get rid of the uses of cpu_is_mx()Shawn Guo
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes platform_device_id to distinguish the different gpio types, IMX1_GPIO on i.mx1, IMX21_GPIO on i.mx21 and i.mx27, IMX31_GPIO on all other i.mx SoCs. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-07-07dmaengine: imx-sdma: pass sdma firmware name via platform dataShawn Guo
It is not good to have cpu_name and to_version encoded into sdma firmware name as variables. For example, there are three TOs of imx51 soc, the sdma script never changes since TO1, which means all three TOs of imx51 uses TO1 version of sdma script. But we have to prepare three identical firmwares, sdma-imx51-to1.bin sdma-imx51-to2.bin and sdma-imx51-to3.bin, to have the kernel capable of running on all three TOs. The patch removes cpu_name and to_version from sdma platform data, and instead uses fw_name to pass the firmware name, so that we can pass the TO version where it's relevant and skip it where only one firmware exists. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-07-07ARM: mxc: clean up imx-dma device registrationShawn Guo
The patch follows the implementation of gpio-mxc device registration to break the concentrated imx-dma device registration into soc specific setup function. Then we can avoid the churn of "#ifdef" and the cpu_is_mx checking on such a long list, which makes no sense, considering more soc supports need to be added and we need to support single image for multiple socs in the long run. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-06-06gpio/mxc: Change gpio-mxc into an upstanding gpio driverShawn Guo
The patch makes necessary changes on gpio-mxc as below to turn it into an upstanding gpio driver. * Add a list to save all mx2 ports references, so that mx2_gpio_irq_handler can walk through all interrupt status registers * Use readl/writel to replace mach-specific accessors __raw_readl/__raw_writel * Change mxc_gpio_init into mxc_gpio_probe function * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to be public at all, and also make some other cleanup on plat-mxc/include/mach/gpio.h at the same time And the patch then migrates mach-imx and mach-mx5 to the updated driver by adding corresponding platform devices. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Olof Johansson <olof@lixom.net> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-18ARM: mx5: Add watchdog support for MX53Fabio Estevam
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2011-02-10ARM: mx5: use .init_early to initialize cpu type, reset address and iomuxerUwe Kleine-König
This used to be done in .map_io which is supposed to only setup the memory mapping. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-12-07ARM: mx5: add support for the two watchdog modulesFabio Estevam
MX51 has two watchdog modules. Add support for both of them. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-11-28ARM: imx: Get the silicon version from the IIM moduleDinh Nguyen
Instead of reading the silicon version from ROM, we should read the SREV register from the IIM. Freescale has dropped all support for MX51 REV1.0, only MX51 REV 2.0 and 3.0 are valid. Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-11-24ARM: imx: Add mx53 support to common msl functions.Dinh Nguyen
Add mx53 support to cpu.c and mm.c. Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-11-24ARM: imx: Add core definitions for MX53Dinh Nguyen
Add iomux, clocks, and memory map for Freescale's MX53 SoC. Add cpu_is_mx53 function to common.h. Add 3 more banks of gpio's to mxc_gpio_ports. Add MX53 phys offset address. Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-11-17ARM: imx: use MXxy_IO_P2V macros to setup static mappingsUwe Kleine-König
This makes less code rely on the virtual constants. To further simplify code and reduce the needed boilerplate when defining the static mappings a new helper macro is defined in mach/hardware.h. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2010-07-26imx: move gpio init after to irq initJason Wang
The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init and irq_init sequence. Usually we will call set_irq_chained_handler in gpio_init functions, this should be called after the irq_init called, otherwise the chained irq can't get propoer irq_chip and this irq will remain masked even we called set_irq_chained_handler. Signed-off-by: Jason Wang <jason77.wang@gmail.com> Tested-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-06-24ARM: imx: get rid of mxc_gpio_initUwe Kleine-König
This function is defined once for each imx family and so is in the way when compiling a kernel for more than one SoC. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2010-03-19i.MX51: remove NFC AXI static mappingSascha Hauer
This area contains the Nand Flash controller registers. There is no need to map them statically as the Nand driver uses ioremap(). Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-03-19i.MX51: map TZIC dynamicallySascha Hauer
This looks cleaner and allows us to call mx51_revision later when we can use ioremap to determine the silicon revision dynamically. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-02-09mxc: Core support for Freescale i.MX5 seriesAmit Kucheria
Add basic clock support, cpu identification, I/O mapping, interrupt controller, serial port and ethernet. Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-17 14:13:27 +0000