| Age | Commit message (Collapse) | Author |
|---|
|
the early_param() call in board-omap3touchbook.c expands to:
static const char __setup_str_early_touchbook_revision[]
__section(.init.rodata) _aligned(1) = tbr;
[...]
and we have a non-const variable being added to the
same section:
static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);
because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.
This patch fixes that for the ehci_hdc_omap_platform_data.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch removes #ifdef around usb_nop_xceiv_register()
from board-omap3evm.c
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The keypad was not working properly after migrating
to matrix_keypad.
Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix omap2_map_common_io for multi-omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tomi.valkeinen@nokia.com: removed evm defconfig changes]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Recent drivers/mfd/twl4030* renames to twl broke compile for
various boards as the series was missing a patch to change
the board-*.c files.
This patch renames include twl4030.h to include twl.h
and also renames twl4030_i2c_ routines.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove old mux code for 34xx
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Replace omap_cfg_reg() with new style signal or gpio functions
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Migrate to smsc911x ethernet driver instead of smc911x driver.
The smsc911x ethernet driver supports NAPI and performs better
under heavy traffic. With the smc911x driver we were witnessing
very high iowait time for high IO load over NFS.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Initialize vmmc and vmmc_aux regulators
Note that the omap3evm_twldata.vmmc1 and omap3evm_twldata.vsim
are set in omap3_evm_i2c_init() to avoid a merge conflict
with the MFD tree. These will be initialized in omap3evm_i2c_boardinfo
as a fix later on.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Added runtime programming for the differences in EHCI interface between
OMAP3EVM revisions (Rev >= E) and (Rev < E).
Changes:
- EHCI PHY reset GPIO pin is 21 on Rev >= E while Rev < E
uses GPIO pin 135.
- Rev >= E uses EHCI Vbus enable GPIO22 line.
- Rev >= E uses GPIO61 to select EHCI port either on main board or
on Mistral Daughter Card (MDC). OMAP3EVM Rev < E doesn't have
EHCI port on main board.
- Currently GPIO61 it programmed to enable EHCI port on main
board only.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
|
|
Added function to differentiate between the OMAP3EVM revisions. The
chip-id of the ethernet PHY is being used for this purpose.
Rev A to D : 0x01150000
Rev >= E : 0x92200000
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add platform init code for EHCI driver.
Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.
Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
boards that use matrix_keypad
Only mach-omap2 boards are currently using matrix_keypad. Allow
mach-omap1 boards to use the old style keypad.h without breaking.
Created against linux-2.6.32-rc5.
Compile tested with omap_3430sdp_defconfig and rx51_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise we'll get compile errors like:
arch/arm/plat-omap/include/mach/keypad.h:38:1: warning: "KEY" redefined
arch/arm/plat-omap/include/mach/keypad.h:39:1: warning: "PERSISTENT_KEY" redefined
...
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add omap3 EVM support
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
