| Age | Commit message (Collapse) | Author |
|---|
|
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
These changes contain the OMAP USB related platform data changes
that were dropped from linux next because of the merge conflicts
as requested by me and Olof. The reason was that at this point
we really should be able to do the arch/arm related changes
separately from driver changes to avoid dependencies between
branches.
These patches were initially part of the USB related MFD patches.
Based on our comments, Roger Quadros quickly reworked these
patches into a shared branch between ARM SoC tree and the MFD
tree, then separate patches for the OMAP platform data and
MFD driver.
Note that this branch will conflict with c1d1cd597fc7
("ARM: OMAP2+: omap_device: remove obsolete pm_lats and
early_device code"). Please see http://lkml.org/lkml/2013/2/11/16
for the merge resolution.
[arnd - resolved the merge conflict]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Let's have a single platform data structure for the OMAP's High-Speed
USB host subsystem instead of having 3 separate ones i.e. one for
board data, one for USB Host (UHH) module and one for USB-TLL module.
This makes the code much simpler and avoids creating multiple copies of
platform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
|
|
This is w.r.t the changes in PHY library to support adding and getting
multiple PHYs of the same type. In the new design, the
binding information between the PHY and the USB controller should be
specified in the platform specific initialization code. So it's been
done here for OMAP platforms.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap1/clock.c
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-cm-t35.c
arch/arm/mach-omap2/board-igep0020.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-omap2/board-omap3logic.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/board-overo.c
arch/arm/mach-omap2/board-rm680.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/twl-common.c
arch/arm/mach-omap2/usb-host.c
arch/arm/mach-omap2/usb-musb.c
|
|
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For common arm zImage existing nand header file
in platform specific location was moved to generic
platform data location, but it contained more than
platform data, remove it. New local header has been
created for exposing functions.
Also move gpmc-nand platform data to platform header
meant for nand from gpmc header file
Signed-off-by: Afzal Mohammed <afzal@ti.com>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
|
|
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can't use hardcoded interrupts for SPARSE_IRQ, and can replace
the hardcoded gpio_base with twl_gpiochip.base after it's been
allocated.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
plat/board.h file is now empty - remove it.
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
* 'fixes-non-critical-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: PM: VP: fix integer truncation error
ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled
ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices()
ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set
ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected
ARM: OMAP1: Fix section mismatch for omap1_init_early()
ARM: OMAP1: Fix typo in lcd_dma.c
ARM: OMAP: mailbox: trivial whitespace fix
ARM: OMAP: Remove definition cpu_is_omap4430()
ARM: OMAP2+: included some headers twice
ARM: OMAP: clock.c: included linux/debugfs.h twice
ARM: OMAP: don't build hwspinlock in vain
ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided
ARM: omap: pandora: fix usbhs platform data
ARM: OMAP: sram: Add am33xx SRAM support (minimal)
ARM: OMAP2+: id: Add am33xx SoC type detection
ARM: OMAP2+: GPMC: Export gpmc_enable_hwecc and gpmc_calculate_ecc
ARM: OMAP: dmtimer: fix missing content/correction in low-power mode support
|
|
It turned out wrong OMAP HSUSB port was configured on pandora,
but still managed to work somehow. This was noticed after enabling
in-kernel mux, where USB muxing was causing other devices not to work,
because hsusb1 pins (instead of hsusb2) were wrongly remuxed, which
are used for other things on pandora.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add platform data for drivers that recently appeared in kernel:
backlight and TWL4030 poweroff support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Conflicts:
arch/arm/mach-exynos/cpu.c
The changes to arch/arm/mach-exynos/cpu.c were moved to
mach-exynos/common.c.
|
|
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into devel-stable
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
|
|
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Omap cleanups conflicted with omap2_dss work in a nontrivial
way, this is the most logical fixup.
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-apollon.c
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-rx51.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.
Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to call omap2_init_common_devices from init_early.
It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.
Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-cleanup
Conflicts:
arch/arm/mach-omap2/pm-debug.c
arch/arm/mach-omap2/pm.h
|
|
|
|
This is needed for the following patches so we can initialize the
rest of the hardware timers later on.
As with the init_irq calls, there's no need to do cpu_is_omap calls
during the timer init as we only care about the major omap generation.
This means that we can initialize the sys_timer with the .timer
entries alone.
Note that for now we just set stubs for the various sys_timer entries
that will get populated in a later patch. The following patches will
also remove the omap_dm_timer_init calls and change the init for the
rest of the hardware timers to happen with an arch_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
This allows us to remove cpu_is_omap calls from init_irq functions.
There should not be any need for cpu_is_omap calls as at this point.
During the timer init we only care about SoC generation, and not about
subrevisions.
The main reason for the patch is that we want to initialize only
minimal omap specific code from the init_early call.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
|
|
to use REGULATOR_SUPPLY arrays.
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit d5ce2b65 "omap3630: nand: fix device size to work in polled mode"
changed values for .devsize in nand platform data, now we have to pass
NAND_BUSWIDTH_16 instead of '1' to select 16bit NAND.
Update pandora's platform data accordingly, also specify appropriate
transfer type.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Several boards defining mtd partitions also defined NAND_BLOCK_SIZE as
SZ_128K. Move the define to common-board-devices.h
This removes multiple defines of NAND_BLOCK_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
I got some build error like below while executing "make omap2plus_defconfig".
CC arch/arm/mach-omap2/board-2430sdp.o
arch/arm/mach-omap2/board-2430sdp.c: In function 'omap_2430sdp_init':
arch/arm/mach-omap2/board-2430sdp.c:247: error: 'GPIOF_OUT_INIT_LOW' undeclared (first use in this function)
arch/arm/mach-omap2/board-2430sdp.c:247: error: (Each undeclared identifier is reported only once
arch/arm/mach-omap2/board-2430sdp.c:247: error: for each function it appears in.)
This patch fixes the build error by include linux/gpio.h instead of mach/gpio.h.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Syed Mohammed Khasim <x0khasim@ti.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
|
|
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Most boards use exactly the same configuration for musb initialization.
Create a default that can be shared amount different boards.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add common-board-devices.c that will contain the code for peripheral
devices initializatoin shared between multiple boards.
Start small with touchscreen initialization.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Conflicts:
arch/arm/mach-omap2/board-overo.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
