| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
|
|
Commit f2bf0e72d000 (ARM: OMAP2+: Add minimal 8250 support
for GPMC) added support for using bootloader timings for some
devices. Turns out we can do the same by looking at the compatible
flags of the child without adding a new function as smc91x has
a similar issue as 8250 with the bootloader timings.
And let's fix the 8250 naming, we should use the device type as
the name like uart instead of 8250 for zoom dts file.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
|
|
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Just initialize things using the bootloader timings like
we've been doing for the legacy booting too. It should be
possible to patch in the GPMC timings for the based on the
TL16CP743C/TL16C754C manual at:
http://www.ti.com/lit/ds/slls644g/slls644g.pdf
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When CONFIG_ARM_LPAE=y the following build warning is generated:
arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
'gpmc_irq_start' is mostly used as 'int', and for a variable, do not
suggest to only use 'unsigned' as its type, so use 'int' instead of
'unsigned' for variable 'gpmc_irq_start'.
Also it will fix the related issue (dummy the real world failure):
arch/arm/mach-omap2/gpmc.c:728:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Cocci spatch "ptr_ret.spatch"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPMC is hardware controller for external memory interfaces.
This patch adds suspend/resume support for GPMC driver.
It also preserves GPMC register configurations across device low-power states
in which GPMC hardware can be powered-off.
gpmc_suspend()/gpmc_resume() are called by default by core PM framework as part
of driver's runtime PM callbacks.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Support for pm_runtime add to GPMC driver.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch enables usage of DT property 'gpmc,num-cs' as already documented in
Documentation/devicetree/bindings/bus/ti-gpmc.txt
Though GPMC hardware supports upto 8 chip-selects, but all chip-selects may
not be available for use because:
- chip-select pin may not be bonded out at SoC device boundary.
- chip-select pin-mux may conflict with other pins usage.
- board level constrains.
gpmc,num-cs allows user to configure maximum number of GPMC chip-selects
available for use on any given platform. This ensures:
- GPMC child nodes having chip-selects within allowed range are only probed.
- And un-used GPMC chip-selects remain blocked.(may be for security reasons).
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from
device-tree) added a device-tree property "gpmc,device-nand" to indicate
is the GPMC child device is NAND. This commit should have updated the
GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt)
to list the property "gpmc,device-nand" as a required property and also
updated the example. However, this property is redundant and not needed
because the GPMC child device node for NAND is called "nand". Therefore,
remove this property.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If any of the GPMC child nodes fails, this shouldn't make the
whole gpmc_probe_dt() function to fail. It is better to just
WARN and allow other devices probe function to succeed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
The GPMC DT probe function use for_each_node_by_name() to search
child device nodes of the GPMC controller. But this function does
not use the GPMC device node as the root of the search and instead
search across the complete Device Tree.
This means that any device node on the DT that is using any of the
GPMC child nodes names searched for will be returned even if they
are not connected to the GPMC, making the gpmc_probe_xxx_child()
function to fail.
Fix this by using the GPMC device node as the search root so the
search will be restricted to its children.
Reported-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
Besides being used to interface with external memory devices,
the General-Purpose Memory Controller can be used to connect
Pseudo-SRAM devices such as ethernet controllers to OMAP2+
processors using the TI GPMC as a data bus.
This patch allows an ethernet chip to be defined as an GPMC
child device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
The gpmc_probe_nor_child() function is used in the GPMC driver to
configure the GPMC for a NOR child device node.
But this function is quite generic and all the NOR specific configuration
is made by the driver of the actual NOR flash memory used.
Other Pseudo-SRAM devices such as ethernet controllers need a similar
setup so by making this function generic it can be used for those too.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
gpmc_probe_nor_child() calls of_platform_device_create() to create a
platform device for the NOR child. If this function fails the value
of ret is returned to the caller but this value is zero since it was
assigned the return of a previous call to gpmc_cs_program_settings()
that had to succeed or otherwise gpmc_probe_nor_child() would have
returned before.
This means that if of_platform_device_create() fails, 0 will be returned
to the caller instead of an appropriate error code.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
When the GPMC driver is probed, we call gpmc_mem_init() to see which
chip-selects have already been configured and enabled by the boot-loader
and allocate space for them. If we fail to allocate space for one
chip-select, then we return failure from the probe and the GPMC driver
will not be available.
Rather than render the GPMC useless for all GPMC devices, if we fail to
allocate space for one chip-select print a warning and disable the
chip-select. This way other GPMC clients can still be used.
There is no downside to this approach, because all GPMC clients need to
request a chip-select before they can use the GPMC and on requesting a
chip-select, if memory has not already been reserved for the chip-select
then it will be.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
With commit 21cc2bd (ARM: OMAP2+: Remove apollon board support) the
variable "boot_rom_space" is now not needed and the code surrounding
this variable can be cleaned up and simplified. Remove unnecessary
definitions and clean-up the comment as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB
of address space. The physical base address where a chip-select starts
is also configurable and must be aligned on a boundary that is equal to
or greater than the size of the address space mapped bt the chip-select.
When enabling a GPMC chip-select, ensure that the base address is aligned
to the appropriate boundary.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
NOR flash is not currently supported when booting with device-tree
on OMAP2+ devices. Add support to detect and configure NOR devices
when booting with device-tree.
Add documentation for the TI GPMC NOR binding.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
Some of the GPMC timings parameters are currently missing from the GPMC
device-tree binding. Add these parameters to the binding documentation
as well as code to read them. Also add either "-ps" or "-ns" suffix to
the GPMC timing properties to indicate whether the timing is in
picoseconds or nanoseconds.
The existing code in gpmc_read_timings_dt() is checking the value of
of_property_read_u32() and only is successful storing the value read
in the gpmc_timings structure. Checking the return value in this case
is not necessary and we can simply read the value, if present, and
store directly in the gpmc_timings structure. Therefore, simplify the
code by removing these checks.
The comment in the gpmc_read_timings_dt() function, "only for OMAP3430"
is also incorrect as it is applicable to all OMAP3+ devices. So correct
this too.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
Adds a function to read the various GPMC chip-select settings from
device-tree and store them in the gpmc_settings structure.
Update the GPMC device-tree binding documentation to describe these
options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
With the addition of the gpmc_cs_program_settings(), we no longer need
or use gpmc_cs_configure() to configure some of the GPMC chip-select
options. So rename the function to gpmc_configure() and remove code that
modifies options in the CONFIG1 register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no common function for configuring these options and
various devices set these options by either programming the GPMC CONFIG1
register directly or by calling gpmc_cs_configure() to set some of the
options.
Add a new function for configuring all of the GPMC options. Having a common
function for configuring this options will simplify code and ease the
migration to device-tree.
Also add a new capability flag to detect devices that support the
address-address-data multiplexing mode.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
The GPMC has various different configuration options such as bus-width,
synchronous or asychronous mode selection, burst mode options etc.
Currently, there is no central structure for storing all these options
when configuring the GPMC for a given device. Some of the options are
stored in the GPMC timing structure and some are directly programmed
into the GPMC configuration register. Add a new structure to store
these options and convert code to use this structure. Adding this
structure will allow us to create a common function for configuring
these options.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
The GPMC has wait-pin signals that can be assigned to a chip-select
to monitor the ready signal of an external device. Add a variable to
indicate the total number of wait-pins for a given device. This will
allow us to detect if the wait-pin being selected is valid or not.
When booting with device-tree read the number of wait-pins from the
device-tree blob. When device-tree is not used set the number of
wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices
that have less wait-pins (such as AM335x) only support booting with
device-tree and so hard-coding the wait-pin number when not using
device-tree is fine.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
|
|
This check is done before the call to gpmc_cs_reserved() and
gpmc_cs_set_reserved() and it's redundant to do it again in each
function. This simplifies the code a bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
Currently gpmc_cs_reserved() return value is somewhat inconsistent,
returning a negative value on an error condition, a positive value
if the chip select is reserved and zero if it's available.
Fix this by returning a boolean value as the function name suggests:
* true if the chip select is reserved,
* false if it's available
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
This function is not used anywhere, so it's safe to remove it.
This means less code to maintain.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
This patch marks a bunch of functions that are local
to gpmc.c file only as static.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
When setting the GPMC device type, make sure any previous
bits are cleared down, before applying the new setting.
For OMAP4+ devices MUXADDDATA is a 2-bit field (bits 9:8)
where as for OMAP2/3 devices it was only a one bit field
(bit 9). For OMAP2/3 devices bit 8 is reserved and the
OMAP documentation says to write a 0 to this bit. So
clearing bit 8 on OMAP2/3 devices should not be a problem.
Hence update the code to handle both bits 8 and 9 for all
devices.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
[jon-hunter@ti.com: updated changelog]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
|
|
Conflicts:
arch/arm/plat-omap/dmtimer.c
|
|
Consistently check errors using the usual method used in the kernel
for much of its history. For instance:
int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
{
int div;
div = gpmc_calc_divider(t->sync_clk);
if (div < 0)
return div;
static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
{
...
return gpmc_cs_set_timings(cs, t);
.....
ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
if (IS_ERR_VALUE(ret))
return ret;
So, gpmc_cs_set_timings() thinks any negative return value is an error,
but where we check that in higher levels, only a limited range are
errors...
There is only _one_ use of IS_ERR_VALUE() in arch/arm which is really
appropriate, and that is in arch/arm/include/asm/syscall.h:
static inline long syscall_get_error(struct task_struct *task,
struct pt_regs *regs)
{
unsigned long error = regs->ARM_r0;
return IS_ERR_VALUE(error) ? error : 0;
}
because this function really does have to differentiate between error
return values and addresses which look like negative numbers (eg, from
mmap()).
So, here's a patch to remove them from OMAP, except for the above.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails)
added code to ensure that GPMC chip-selects could not be requested until the
device probe was successful. The chip-selects should have been
unreserved at the end of the probe function, but the code to unreserve
them appears to have ended up in the gpmc_calc_timings() function and
hence, this is causing problems requesting chip-selects. Fix this merge
error by unreserving the chip-selects at the end of the probe, but
before we call the gpmc child probe functions (for device-tree) which
request a chip-select.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Philip Avinash <avinashphilip@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
[tony@atomide.com: updated description to add breaking commit id]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC board specific changes from Arnd Bergmann:
"These updates are all for board specific code, including
- defconfig updates for shmobile, davinci, bcm2835, imx, omap and
tegra
- SD/MMC and I2C support on bcm2835 (Raspberry PI)
- minor updates for PXA
- shmobile updates to GPIO usage in board files
- More things in OMAP board files are moved over to device tree
probing
- Better support for audio devices on some OMAP platforms"
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: imx_v4_v5_defconfig: Add VPU support
ARM: imx: configs: enable netfilter support
ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
ARM: shmobile: armadillo800eva: set clock rates before timer init
ARM: tegra: defconfig updates
ARM: shmobile: mackerel: Use gpio_request_one()
ARM: shmobile: kzm9g: Use gpio_request_one()
ARM: shmobile: bonito: Use gpio_request_one()
...
|
|
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
|
|
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
|
|
This patch adds device tree bindings for OMAP OneNAND devices.
Tested on an OMAP3 3430 IGEPv2 board.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If the GPMC probe fails, devices that use the GPMC (such as ethernet
chips, flash memories, etc) can still allocate a GPMC chip-select and
register the device. On the OMAP2420 H4 board, this was causing the
kernel to crash after the gpmc probe failed and the board attempted
to start networking. Prevent this by marking all the chip-selects as
reserved by default and only make them available for devices to request
if the GPMC probe succeeds.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
for_each_node_by_name() automatically calls of_node_put() on each
node passed; so don't do it explicitly unless there's an error.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As apollon board doesn't used anymore, remove it.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: dropped uncompress.h changes, it's gone]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove now-obsolete code from arch/arm/mach-omap2/omap_device.c. This
mostly consists of removing the first attempt at device PM latency
handling. This was never really used, has been replaced by the common
dev_pm_qos code, and needs to go away as part of the DT conversion.
Also, the early platform_device creation code has been removed, as it
appears to be unused.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On DT driven boards, the gpmc node will match the driver. Hence, there's
no need to do that unconditionally from the initcall.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This way the initcalls don't run on other SoCs on multiplatform
kernels. Otherwise we'll get something like this when booting
on vexpress:
omap_hwmod: _ensure_mpu_hwmod_is_setup: MPU initiator hwmod mpu not yet registered
...
WARNING: at arch/arm/mach-omap2/pm.c:82 _init_omap_device+0x74/0x94()
_init_omap_device: could not find omap_hwmod for mpu
...
omap-dma-engine omap-dma-engine: OMAP DMA engine driver
...
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
