summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/mmc-twl4030.h
AgeCommit message (Collapse)Author
2009-09-23omap_hsmmc: support for deeper power saving statesDenis Karpov
Support for multi-level dynamic power saving states in omap_hsmmc (ENABLED->DISABLED->OFF). In the "deepest" state (OFF) we switch off the voltage regulators. Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Matt Fleming <matt@console-pimps.org> Cc: Ian Molton <ian@mnementh.co.uk> Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Cc: Denis Karpov <ext-denis.2.karpov@nokia.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Philip Langdale <philipl@overt.org> Cc: "Madhusudhan" <madhu.cr@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23omap_hsmmc: make use of new MMC_CAP_NONREMOVABLE host capabilityAdrian Hunter
Let the board specify that a card is nonremovable e.g. eMMC Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Matt Fleming <matt@console-pimps.org> Cc: Ian Molton <ian@mnementh.co.uk> Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com> Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com> Cc: Denis Karpov <ext-denis.2.karpov@nokia.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: Philip Langdale <philipl@overt.org> Cc: "Madhusudhan" <madhu.cr@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-05-28ARM: OMAP3: mmc-twl4030 uses regulator frameworkDavid Brownell
Decouple the HSMMC glue from the twl4030 as the only regulator provider, using the regulator framework instead. This makes the glue's "mmc-twl4030" name become a complete misnomer ... this code could probably all migrate into the HSMMC driver now. Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD), plus some other boards (including Overo) after they were converted to set up MMC regulators properly. Eventually all boards should just associate a regulator with each MMC controller they use. In some cases (Overo MMC2 and Pandora MMC3, at least) that would be a fixed-voltage regulator with no real software control. As a temporary hack (pending regulator-next updates to make the "fixed.c" regulator become usable) there's a new ocr_mask field for those boards. Patch updated with a fix for disabling vcc_aux by Adrian Hunter <adrian.hunter@nokia.com> Cc: Pierre Ossman <drzeus-list@drzeus.cx> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: mmc-twl4030 allow arbitrary slot names, v3Adrian Hunter
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: mmc-twl4030 add cover switchAdrian Hunter
Allow a cover switch to be used to cause a rescan of the MMC slot. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: mmc-twl4030 init passes device nodes back, v2David Brownell
When setting up HSMMC devices, pass the device nodes back so board code can linking them to their power supply regulators. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2009-03-23ARM: OMAP3: mmc-twl4030 voltage cleanupDavid Brownell
Correct twl4030 MMC power switching: fix voltage ranges reported for each slot, and handle them fully. Lies corrected: - MMC-1 doesn't support the 2.6-2.7 Volt range - MMC-2 can't normally support anything except 1.8V Omissions corrected - MMC-1 *does* handle the 2.8-2.9 Volt range - MMC-2 can handle 2.5-3.2 Volt cards, given a transceiver Add transciever support for MMC-2; enable it for Overo and Pandora. (Depends on something else to have set up pinmuxing for control signals instead of as MMC2_DAT4..7 pins.) Also shrink twl4030_hsmmc_info a smidgeon ... padding is all gone. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
2008-12-10omap mmc: Add low-level initialization for hsmmc controllerTony Lindgren
Add low-level initialization for hsmmc controller. Merged into this patch patch are various improvments and board support by Grazvydas Ignotas and David Brownell. Also change wire4 to be wires, as some newer controllers support 8 data lines. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>