| Age | Commit message (Collapse) | Author |
|---|
|
On OMAP5 / DRA7, prevent a CPU powerdomain OFF and resulting MPU OSWR
and instead attempt a CPU RET and side effect, MPU RET in suspend.
NOTE: the hardware was originally designed to be capable of achieving
deep power states such as OFF and OSWR, however due to various issues
and risks, deepest valid state was determined to be CSWR - hence we use
the errata framework to handle this case.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: updates]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
Enables MPUSS ES2 power management mode using ES2_PM_MODE in
AMBA_IF_MODE register.
0x0: OMAP5 ES1 behavior, CPU cores would enter and exit OFF mode together.
Broken! Fortunately, we do not support this anymore.
0x1: OMAP5 ES2, DRA7 behavior, CPU cores are allowed to enter/exit OFF mode
independently.
This is one time settings thanks to always ON domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor conflict resolutions, consolidation for DRA7]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The wakeup gen mask/unmask callback uses the irq element of the
irq_data to setup. The irq is the linux virtual irq number and
is same as the hardware irq number only when the parent irqchip
is setup as a legacy domain. When it is used as a linear domain,
the virtual irqs are allocated dynamically and wakeup gen code
cannot rely on these numbers to access the irq registers. Instead
use the hwirq element of the irq_data which represent the physical
irq number.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
AM43x has 224 interrupts and 7 banks, make it as maximum values. Keep
default values as earlier, if am43x is detected, update interrupts and
banks accordingly.
Also AM43x has only one cpu, ensure that clearing bitmask at wakeupgen
is done only for the single existing cpu, existing code assumes that
there are two cpu's.
If bitmask is cleared in wakeupgen for the nonexistent second cpu,
an imprecise abort happens as soon as Kernel switches to user space.
It was rootcaused by Sekhar Nori <nsekhar@ti.com>.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
When applying RT patch on top of Linux, spinlocks are
implemented as RT-mutexes, which means they are preemptable.
Current GIC implementation on OMAP is using a spinlock
to protect against preemption. As it turns out, we need
to convert that lock into a raw_spinlock so that OMAP's
interrupt controller works as expected after RT-patch
is applied.
This patch is simply to decrease the amount of changes
RT-team needs to carry out of tree. It doesn't cause any
changes in behavior.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/fixes-non-critical
A few non-critical fixes/cleanups for samsung platforms.
* 'v3.7-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
+ sync to 3.6-rc6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This can be local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The wakeupgen context-save code reads and stores the AUXCOREBOOT0 and
AUXCOREBOOT1 register contents twice. This seems like a waste of
time, so, remove the duplicates.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The wakeupgen context-save code reads AUXCOREBOOT0 register
instead of AUXCOREBOOT1 register contents while saving AUXCOREBOOT1.
Fix the same.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If NR_IRQS is less than MAX_IRQS, we end up writing past the
irq_target_cpu array in omap_wakeupgen_init():
/* Associate all the IRQs to boot CPU like GIC init does. */
for (i = 0; i < max_irqs; i++)
irq_target_cpu[i] = boot_cpu;
This can happen if SPARSE_IRQ is enabled as by default NR_IRQS is
set to 16. Without this patch we're overwriting other data during
the boot.
Looks like a similar fix was posted by Benoit Cousson earlier
as "ARM: OMAP2+: wakeupgen: Fix wrong array size for irq_target_cpu"
but was lost.
Cc: stable@vger.kernel.org
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 and OMAP5 share same WakeupGen IP with below few udpates on OMAP5.
- Additional 32 interrupt support is added w.r.t OMAP4 design.
- The AUX CORE boot registers are now made accessible from non-secure SW.
- SAR offset are changed and PTMSYNC* registers are removed from SAR.
Patch updates the WakeupGen code accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Several function declarations used only in the files in which they're
declared should include the static keyword, but don't:
arch/arm/mach-omap2/serial.c:248:6: warning: symbol 'cmdline_find_option' was not declared. Should it be static?
arch/arm/mach-omap2/omap-wakeupgen.c:259:6: warning: symbol 'irq_sar_clear' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:878:27: warning: symbol 'rx51_vibra_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:882:27: warning: symbol 'rx51_audio_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:201:29: warning: symbol 'omap_panda_wlan_data' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:393:24: warning: symbol 'omap4_panda_dvi_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:403:12: warning: symbol 'omap4_panda_dvi_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap4panda.c:464:6: warning: symbol 'omap4_panda_display_init' was not declared. Should it be static?
arch/arm/mach-omap2/hsmmc.c:434:6: warning: symbol 'omap_init_hsmmc' was not declared. Should it be static?
arch/arm/mach-omap2/hwspinlock.c:31:12: warning: symbol 'hwspinlocks_init' was not declared. Should it be static?
arch/arm/mach-omap1/timer.c:58:12: warning: symbol 'omap1_dm_timer_init' was not declared. Should it be static?
arch/arm/mach-omap1/fpga.c:90:6: warning: symbol 'innovator_fpga_IRQ_demux' was not declared. Should it be static?
Mark all of these as static.
Thanks to Arnd Bergmann <arnd@arndb.de> for pointing out a typo in the
original patch description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: David Anders <x0132446@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
When CONFIG_HOTPLUG_CPU=n, there are unused functions in wakeupgen:
arch/arm/mach-omap2/omap-wakeupgen.c:181: warning: 'wakeupgen_irqmask_all' defined but not used
Fix this by moving all the functions only used when CONFIG_HOTPLUG_CPU=y
together and wrapping in an #ifdef.
No functional changes.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add WakeupGen and secure GIC low power support to save and restore
it's registers. WakeupGen Registers are saved to pre-defined SAR RAM layout
and the restore is automatically done by hardware(ROM code) while coming
out of MPUSS OSWR or Device off state. Secure GIC is saved using secure
API and restored by hardware like WakeupGen.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Program non-boot CPUs to hit lowest supported power state
when it is off-lined using cpu hotplug framework.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP WakeupGen is the interrupt controller extension used along
with ARM GIC to wake the CPU out from low power states on
external interrupts.
The WakeupGen unit is responsible for generating the wakeup event
from the incoming interrupts and enable bits. It is implemented
in the MPU always ON power domain. During normal operation,
WakeupGen delivers the external interrupts directly to the GIC.
WakeupGen specification has one restriction as per Veyron version 1.6.
It is SW responsibility to program interrupt enabling/disabling
coherently in the GIC and in the WakeupGen enable registers. That is, a
given interrupt for a given CPU is either enable at both GIC and WakeupGen,
or disable at both, but no mix. That's the reason the WakeupGen is
implemented as an extension of GIC.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
