| Age | Commit message (Collapse) | Author |
|---|
|
The PHY framework uses the phy consumer data populated in platform data in the
case of non-dt boot to return the reference to the PHY when the controller
(PHY consumer) requests for it. So populated the phy consumer data in the platform
data of twl usb.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DPI driver gets currently the vdds_dsi regulator via omapdss device.
This is not correct, and we'll change the DPI driver to get the
regulator directly via omapdss_dpi.0 device.
This patch changes the relevant board files to add vdds_dsi supply for
omapdss_dpi.0 device.
Note that the vdds_dsi supply for omapdss device is still left there, as
the current display driver uses it. When both the board files and the
display driver has been changed, we can remove the unused supply.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC board specific changes from Arnd Bergmann:
"These updates are all for board specific code, including
- defconfig updates for shmobile, davinci, bcm2835, imx, omap and
tegra
- SD/MMC and I2C support on bcm2835 (Raspberry PI)
- minor updates for PXA
- shmobile updates to GPIO usage in board files
- More things in OMAP board files are moved over to device tree
probing
- Better support for audio devices on some OMAP platforms"
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: imx_v4_v5_defconfig: Add VPU support
ARM: imx: configs: enable netfilter support
ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
ARM: shmobile: armadillo800eva: set clock rates before timer init
ARM: tegra: defconfig updates
ARM: shmobile: mackerel: Use gpio_request_one()
ARM: shmobile: kzm9g: Use gpio_request_one()
ARM: shmobile: bonito: Use gpio_request_one()
...
|
|
With the recent twl related changes we can now get:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15f88): Section mismatch in
reference from the function sdp3430_twl_gpio_setup() to the function
.init.text:omap_twl4030_audio_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap_twl4030_audio_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap_twl4030_audio_init is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x16968): Section mismatch in
reference from the function zoom_twl_gpio_setup() to the function
.init.text:omap_twl4030_audio_init()
The function zoom_twl_gpio_setup() references
the function __init omap_twl4030_audio_init().
This is often because zoom_twl_gpio_setup lacks a __init
annotation or the annotation of omap_twl4030_audio_init is wrong.
Fix this by removing __init from omap_twl4030_audio_init() as
suggested by Peter Ujfalusi <peter.ujfalusi@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
the fields must be null-terminated:
the caller may use it as null-terminted string, next.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Boards with special audio routing can pass a custom omap_tw4030_pdata to the
audio machine driver.
At the same time update the board files using the same audio driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
|
|
Select the most commonly used audio configuration on boards with twl4030
audio:
Headset, Handsfree output and Line in input
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
|
|
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
|
|
On OMAP4 boards using the TWL6030 PMIC, the sys_drm_msecure is
connected to the MSECURE input of the TWL6030 PMIC. This signal
controls the secure-mode operation of the PMIC. If its not mux'd
correctly, some functionality of the PMIC will not be accessible since
the PMIC will be in secure mode.
For example, if the TWL RTC is in secure mode, most of its registers
are read-only, meaning (re)programming the RTC (e.g. for wakeup from
suspend) will fail.
To fix, ensure the signal is properly mux'd as output when TWL is
intialized.
This fix is required when using recent versions of u-boot (>= v2012.04.01)
since u-boot is no longer setting the default mux for this pin.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 24d7b40a (ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for
MPU-SS) updated the regulator name used for the MPU regulator, but only
updated OMAP3, not OMAP4. Fix the OMAP4 name as well, otherwise CPUfreq
fails to find the MPU regulator.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Conflicts resolved same as Tony did in his later dependent branch:
arch/arm/mach-omap1/clock.c
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-cm-t35.c
arch/arm/mach-omap2/board-igep0020.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-omap2/board-omap3logic.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/board-overo.c
arch/arm/mach-omap2/board-rm680.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/twl-common.c
arch/arm/mach-omap2/usb-host.c
arch/arm/mach-omap2/usb-musb.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
|
|
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
|
|
Currently, a dummy omap_device is created for the MPU sub-system so
that a device node exists for MPU DVFS. Specifically, for the
association of MPU OPPs to a device node, and so that a voltage
regulator can be mapped to a device node.
For drivers to get a handle to this device node, an OMAP-specific API
has been used. However, the kernel already has device nodes for the
CPU(s) in the system, so we can use those instead of an OMAP-specific
dummy device and then drivers (like OMAP CPUfreq) can use generic
APIs.
To use the existing CPU device nodes, modify the OPP creation and
regulator registration to use the CPU0 device node for registraion.
NOTE: this patch always uses CPU0 as the device node. On all
OMAPs today, MPU DVFS scales all CPUs together, so this will
not be a problem, but this assumption will need to be changed
if independently scalable CPUs are introduced.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
On OMAP4 the i2c1 bus is dedicated for the PMIC and audio related devices.
Manufacturers can opt to use different codec than twl6040 and also can add
audio related IC to the bus (external amplifier for example on SDP4430).
Make it possible to add different set of additional devices to i2c1 bus on
OMAP4 boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for removal of irqs.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
HDMI requires vdda_hdmi_dac (vdac) power for operation. The regulator,
or the regulator supplying the vdac, has been enabled by default and
things have worked without the HDMI driver enabling the vdac.
I encountered the problem when implementing HDMI device tree support,
where the regulator was not enabled by default.
This patch adds the vdda_hdmi_dac to twl-common.c so that the HDMI
driver can use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
All the unnessary functions in omap-phy-internal is removed.
These functionality are now handled by omap-usb2 phy driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Linux 3.6-rc4
|
|
not enabled
Fixes:
CC arch/arm/mach-omap2/twl-common.o arch/arm/mach-omap2/twl-common.c:562: error: conflicting types for ‘omap_twl4030_audio_init’
arch/arm/mach-omap2/twl-common.h:62: error: previous declaration of ‘omap_twl4030_audio_init’ was here
make[1]: *** [arch/arm/mach-omap2/twl-common.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
When building the kernel with !SND_OMAP_SOC_OMAP_TWL4030
Reported-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
audio driver
Since several OMAP3 based boards will be using the unified simple audio
driver it is better to not have duplicated code in the board files for this
purpose.
Board files can call omap_twl4030_audio_init(); to set up the needed device
for the audio support.
For example:
omap_twl4030_audio_init("omap3beagle", 26000000);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on 3430/n900, OMAP3530/Overo Fire, 3730/Overo FireSTORM,
3730/Beagle-xM.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical arm-soc bug fixes from Arnd Bergmann:
"These were submitted as bug fixes before v3.5 but not considered
important enough to be included in it."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM:vt8500: Convert to use .restart and remove arch_reset()
ARM: davinci: da8xx: fix interrupt handling
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: mxs/tx28: fix odd include
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
...
|
|
Correcting spelling typo in mach-omap2
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on OMAP4430/Panda.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes-non-critical
|
|
If the kernel is built only for OMAP2 the following warning will show up:
arch/arm/mach-omap2/twl-common.c:52: warning: ‘twl_set_voltage’ defined but not used
arch/arm/mach-omap2/twl-common.c:58: warning: ‘twl_get_voltage’ defined but not used
The twl_set/get_voltage callbacks only used when OMAP3/4 is selected.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The TWL driver has been converted to use SPARSE_IRQ and no longer
needs to be passed IRQ base/end. Since driver no longer uses these
fields, so remove them from the reamaining users.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
V1V8 supply from twl6030 commonly used as VIO for the machine.
V2V1 is adviced to supply the twl6040, and also to feed the twl6030's
VCXIO_IN, and VDAC_IN inputs.
Create the common regulator configurations for these regulators:
Make the V2V1 as supply_regulator for VCXIO, VDAC.
Add twl6040 (1-004b) as consumer for V1V8, and V2V1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the pm regulator changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into pm-regulator
Conflicts:
arch/arm/mach-omap2/twl-common.c
|
|
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
VDD1 is used for MPU voltage, VDD2 is for IVA and VDD3 is for CORE.
These are needed by DVFS. This patch also adds external controller
support for these regulators, the default I2C control channel can't
be used to modify the voltages for these regulators on TWL6030.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
VDD1 and VDD2 now use voltage processor for controlling the regulators.
This is done by passing additional voltdm data during the regulator init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
VDD1 and VDD2 are the core voltage regulators on OMAP3. VDD1 is used
to control MPU/IVA voltage, and VDD2 is used for CORE. These regulators
are needed by DVFS.
Voltage ranges for VDD1 and VDD2 are taken from twl4030/twl5030 data manuals:
- SWCS019L : TWL4030 ES3.1 Data Manual rev L
- SWCS030E : TWL5030 ES1.2 Data Manual rev E
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
VUSB is a fixed regulator, so get rid of the apply_uV constraint
for it, which fixes the following error seen at boot on omap4
SDP and PANDA boards.
machine_constraints_voltage: VUSB: failed to apply 3300000uV constraint
twl_reg twl_reg.46: can't register VUSB, -22
twl_reg: probe of twl_reg.46 failed with error -22
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Current code registers voltage layer details for TWL PMIC even when a TWL
has not been registered. Fix this to only register the TWL with voltage
layer when the TWL PMIC is initialized by board-level code.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP DSS normally gets power from VCXIO on OMAP4. Add configuration for
this into twl-common.c
Mark VCXIO as always_on, as VCXIO is used by multiple components,
including the MPU, and turning it off when DSS doesn't need it would
lead the device to halt.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.
Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Commit b22f954 (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.
Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:
arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'
Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
