summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2
AgeCommit message (Collapse)Author
2011-05-10treewide: fix a few typos in commentsJustin P. Mattock
- kenrel -> kernel - whetehr -> whether - ttt -> tt - sss -> ss Signed-off-by: Justin P. Mattock <justinmattock@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-29arm: Fold irq_set_chip/irq_set_handlerThomas Gleixner
Use irq_set_chip_and_handler() instead. Converted with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-03-29arm: Cleanup the irq namespaceThomas Gleixner
Convert to the new function names. Automated with coccinelle. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-03-27Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: hwspinlock: depend on OMAP4 ARM: OMAP2+: Fix warnings for GPMC interrupt OMAP4: PandaBoard: remove unused power regulators arm: mach-omap2: omap_l3_smx: fix irq handler setup arm: mach-omap2: devices: fix omap3_l3_init() return value
2011-03-24Merge branch 'v4l_for_linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6 * 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits) [media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t [media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly [media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE [media] v4l: soc-camera: Store negotiated buffer settings [media] rc: interim support for 32-bit NEC-ish scancodes [media] mceusb: topseed 0x0011 needs gen3 init for tx to work [media] lirc_zilog: error out if buffer read bytes != chunk size [media] lirc: silence some compile warnings [media] hdpvr: use same polling interval as other OS [media] ir-kbd-i2c: pass device code w/key in hauppauge case [media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap [media] remove the old RC_MAP_HAUPPAUGE_NEW RC map [media] rc/keymaps: Rename Hauppauge table as rc-hauppauge [media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping [media] rc-rc5-hauppauge-new: Add support for the old Black RC [media] rc-rc5-hauppauge-new: Add the old control to the table [media] rc-winfast: Fix the keycode tables [media] a800: Fix a few wrong IR key assignments [media] opera1: Use multimedia keys instead of an app-specific mapping [media] dw2102: Use multimedia keys instead of an app-specific mapping ... Fix up trivial conflicts (remove/modify and some real conflicts) in: arch/arm/mach-omap2/devices.c drivers/staging/Kconfig drivers/staging/Makefile drivers/staging/dabusb/dabusb.c drivers/staging/dabusb/dabusb.h drivers/staging/easycap/easycap_ioctl.c drivers/staging/usbvideo/usbvideo.c drivers/staging/usbvideo/vicam.c
2011-03-24Merge branch 'for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (90 commits) mfd: Push byte swaps out of wm8994 bulk read path mfd: Rename ab8500 gpadc header mfd: Constify WM8994 write path mfd: Push byte swap out of WM8994 bulk I/O mfd: Avoid copying data in WM8994 I2C write mfd: Remove copy from WM831x I2C write function mfd: Staticise WM8994 PM ops regulator: Add a subdriver for TI TPS6105x regulator portions v2 mfd: Add a core driver for TI TPS61050/TPS61052 chips v2 gpio: Add Tunnel Creek support to sch_gpio mfd: Add Tunnel Creek support to lpc_sch pci_ids: Add Intel Tunnel Creek LPC Bridge device ID. regulator: MAX8997/8966 support mfd: Add WM8994 bulk register write operation mfd: Append additional read write on 88pm860x mfd: Adopt mfd_data in 88pm860x input driver mfd: Adopt mfd_data in 88pm860x regulator mfd: Adopt mfd_data in 88pm860x led mfd: Adopt mfd_data in 88pm860x backlight mfd: Fix MAX8997 Kconfig entry typos ...
2011-03-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6: (140 commits) MAINTAINERS: de-orphan fbdev. MAINTAINERS: Add file pattern for fb dt bindings. video: Move sm501fb devicetree binding documentation to a better place. fbcon: fix situation where fbcon gets deinitialised and can't reinit. video, sm501: add OF binding to support SM501 video, sm501: add edid and commandline support video, sm501: add I/O functions for use on powerpc video: Fix EDID macros H_SYNC_WIDTH and H_SYNC_OFFSET fbcon: Bugfix soft cursor detection in Tile Blitting video: add missing framebuffer_release in error path video: metronomefb: add __devexit_p around reference to metronomefb_remove video: hecubafb: add __devexit_p around reference to hecubafb_remove drivers:video:aty:radeon_base Fix typo occationally to occasionally atmel_lcdfb: add fb_blank function atmel_lcdfb: implement inverted contrast pwm video: s3c-fb: return proper error if clk_get fails uvesafb,vesafb: create WC or WB PAT-entries video: ffb: fix ffb_probe error path radeonfb: Let hwmon driver probe the "monid" I2C bus fbdev: sh_mobile_lcdc: checking NULL instead of IS_ERR() ...
2011-03-23Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits) ARM: Update (and cut down) mach-types ARM: 6771/1: vexpress: add support for multiple core tiles ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime ARM: pgtable: add pud-level code ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks ARM: Use long long format when printing meminfo physical addresses ARM: integrator: add Integrator/CP sched_clock support ARM: realview/vexpress: consolidate SMP bringup code ARM: realview/vexpress: consolidate localtimer support ARM: integrator/versatile: consolidate FPGA IRQ handling code ARM: rationalize versatile family Kconfig/Makefile ARM: realview: remove old AMBA device DMA definitions ARM: versatile: remove old AMBA device DMA definitions ARM: vexpress: use new init_early for clock tree and sched_clock init ARM: realview: use new init_early for clock tree and sched_clock init ARM: versatile: use new init_early for clock tree and sched_clock init ARM: integrator: use new init_early for clock tree init ...
2011-03-23OMAP4: add clk32kg data to omap4panda and blaze board fileBalaji T K
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied from Phoenix TWL6030. Add CLK32KG platform data to blaze and omap4panda board file. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-03-22[media] omap2: Fix camera resources for multiomapSergio Aguirre
Make sure the kernel can be compiled with both OMAP2 and OMAP3 camera support linked in, and give public symbols proper omap2/omap3 prefixes. Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-03-22[media] omap3: Add function to register omap3isp platform device structureLaurent Pinchart
The omap3isp platform device requires platform data. Instead of registering the device in omap2_init_devices(), export an omap3_init_camera() function to fill the device structure with the platform data pointer and register the device. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-03-22[media] omap3: Remove unusued ISP CBUFF resourceSergio Aguirre
The ISP CBUFF module isn't use, its resource isn't needed. Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-03-22[media] ARM: OMAP3: Update Camera ISP definitions for OMAP3630Tuukka Toivonen
Add new/changed base address definitions and resources for OMAP3630 ISP. The OMAP3430 CSI2PHY block is same as the OMAP3630 CSIPHY2 block. But the later name is chosen as it gives more symmetry to the names. Signed-off-by: Tuukka Toivonen <tuukkat76@gmail.com> Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2011-03-22Merge branch 'for-paul' of git://gitorious.org/linux-omap-dss2/linuxPaul Mundt
Conflicts: arch/arm/mach-omap2/board-overo.c Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-03-20Merge branches 'fixes', 'pgt-next' and 'versatile' into develRussell King
2011-03-18ARM: OMAP2+: Fix warnings for GPMC interruptBalaji T K
Commit db97eb7dfe13f6c04f0a0e77c32e2691f563ab8b (omap: gpmc: enable irq mode in gpmc) enabled interrupts for GPMC (General Purpose Memory Controller). However, looks like this patch only works on omap3. Fix the issues to avoid warnings on omap4 during the boot. GPMC: number of chip select is 8, CS0 to CS7. One less IRQ allocated throws below warning at boot: [ 0.429290] Trying to install type control for IRQ409 [ 0.429290] Trying to set irq flags for IRQ409 Resolve following warning messages in boot when irq chip is not set: [ 0.429229] Trying to install interrupt handler for IRQ402 [ 0.429229] Trying to install interrupt handler for IRQ403 [ 0.429229] Trying to install interrupt handler for IRQ404 [ 0.429260] Trying to install interrupt handler for IRQ405 [ 0.429260] Trying to install interrupt handler for IRQ406 [ 0.429260] Trying to install interrupt handler for IRQ407 [ 0.429290] Trying to install interrupt handler for IRQ408 Resolve following warning in OMAP4: [ 0.429290] gpmc: irq-20 could not claim: err -22 Signed-off-by: Balaji T K <balajitk@ti.com> [tony@atomide.com: combined patches into one, updated comments] Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-18OMAP4: PandaBoard: remove unused power regulatorsDavid Anders
the pandaboard does not use the VUSIM or VAUX1 power regulators on the TWL6030 and are left floating. if the VUSIM and VAUX1 power regulators are initilized, noise on the unloaded regulators generates an overcurrent interrupt causing the system to power down. this patch removes the initialization of the unused power regulators of VUSIM and VAUX1. Signed-off-by: David Anders <x0132446@ti.com> Acked-by: Andy Green <andy.green@linaro.org> Acked-by: Anand Gadiyar <gadiyar@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-18arm: mach-omap2: omap_l3_smx: fix irq handler setupAaro Koskinen
The handler function may be called from the point it is registered. Since the handler inspects IRQ numbers, we must set them up before registration. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-18arm: mach-omap2: devices: fix omap3_l3_init() return valueAaro Koskinen
Fix the return value for the successful case. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-18OMAP4: PandaBoard: Adding DVI supportMurthy, Raghuveer
Adding DVI support to OMAP4 PandaBoard. PandaBoard uses TFP410 DVI Framer chip http://focus.ti.com/lit/ds/symlink/tfp410.pdf The TFP410 gets its power enable and display data over GPIO lines muxed in from OMAP4430. PandaBoard supports other LCD displays through expansion connectors, following board rework. This will disable the DVI interface. However, the existing mux settings remain the same PandaBoard additionally supports display over HDMI interface. It is mutually exclusive to display over DVI. Hence the mux settings need to be configured seperately, as and when HDMI is enabled Also, I2C3 bus used for reading EDID data from DVI Monitors is registered here. Since the design is similar to BeagleBoard, the code for the same is taken from the kernel.org commit e3333f48dd5cb21 (omap: Adding beagle i2c eeprom driver to read EDID) Reviewed-by: Manjunath G Kondaiah <manjugk@ti.com> Reviewed-by: Anand Gadiyar <gadiyar@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Reviewed-by: Sumit Semwal <sumit.semwal@ti.com> Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com> [tomi.valkeinen@ti.com: fixed conflicts with HDMI] Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-17Merge branch 'omap-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits) omap: zoom: host should not pull up wl1271's irq line arm: plat-omap: iommu: fix request_mem_region() error path OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430 omap4: mux: Remove duplicate mux modes omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected omap4: board-omap4panda: Initialise the serial pads omap3: board-3430sdp: Initialise the serial pads omap4: board-4430sdp: Initialise the serial pads omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init omap2+: mux: Remove the use of IDLE flag omap2+: Add separate list for dynamic pads to mux perf: add OMAP support for the new power events OMAP4: Add IVA OPP enteries. OMAP4: Update Voltage Rail Values for MPU, IVA and CORE OMAP4: Enable 800 MHz and 1 GHz MPU-OPP OMAP3+: OPP: Replace voltage values with Macros OMAP3: wdtimer: Fix CORE idle transition Watchdog: omap_wdt: add fine grain runtime-pm ... Fix up various conflicts in - arch/arm/mach-omap2/board-omap3evm.c - arch/arm/mach-omap2/clock3xxx_data.c - arch/arm/mach-omap2/usb-musb.c - arch/arm/plat-omap/include/plat/usb.h - drivers/usb/musb/musb_core.h
2011-03-16Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits) ARM: 6806/1: irq: introduce entry and exit functions for chained handlers ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas ARM: 6747/1: P2V: Thumb2 support ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9 ARM: 6772/1: errata: possible fault MMU translations following an ASID switch ARM: 6776/1: mach-ux500: activate fix for errata 753970 ARM: 6794/1: SPEAr: Append UL to device address macros. ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files. ARM: 6681/1: SPEAr: add debugfs support to clk API ARM: 6703/1: SPEAr: update clk API support ARM: 6679/1: SPEAr: make clk API functions more generic ARM: 6737/1: SPEAr: formalized timer support ...
2011-03-16Merge branch 'p2v' into develRussell King
Conflicts: arch/arm/kernel/module.c arch/arm/mach-s5pv210/sleep.S
2011-03-16Merge branch 'misc' into develRussell King
Conflicts: arch/arm/Kconfig
2011-03-16Merge branches 'at91', 'ep93xx', 'errata', 'footbridge', 'fncpy', 'gemini', ↵Russell King
'irqdata', 'pm', 'sh', 'smp', 'spear', 'ux500' and 'via' into devel
2011-03-16Merge branch 'usb-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6 * 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits) USB: Add support for SuperSpeed isoc endpoints xhci: Clean up cycle bit math used during stalls. xhci: Fix cycle bit calculation during stall handling. xhci: Update internal dequeue pointers after stalls. USB: Disable auto-suspend for USB 3.0 hubs. USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol. xhci: Return canceled URBs immediately when host is halted. xhci: Fixes for suspend/resume of shared HCDs. xhci: Fix re-init on power loss after resume. xhci: Make roothub functions deal with device removal. xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports. xhci: Return a USB 3.0 hub descriptor for USB3 roothub. xhci: Register second xHCI roothub. xhci: Change xhci_find_slot_id_by_port() API. xhci: Refactor bus suspend state into a struct. xhci: Index with a port array instead of PORTSC addresses. USB: Set usb_hcd->state and flags for shared roothubs. usb: Make core allocate resources per PCI-device. usb: Store bus type in usb_hcd, not in driver flags. usb: Change usb_hcd->bandwidth_mutex to a pointer. ...
2011-03-16OMAP4: HDMI: Add HDMI structure in the board file for OMAP4 PANDAK, Mythri P
Adding board file structure for display which adds the display structure with HDMI as the default driver when the display init is called. HDMI GPIO configurations are also done in this file. Signed-off-by: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-16OMAP4: HDMI: Add HDMI structure in the board file for OMAP4 SDPMythri P K
Adding board file structure for display which adds the display structure with HDMI as the default driver when the display init is called. HDMI GPIO configurations are also done in this file. Signed-off-by: Mythri P K <mythripk@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-14Merge branches 'devel-mux' and 'devel-misc' into omap-for-linusTony Lindgren
2011-03-14omap: zoom: host should not pull up wl1271's irq lineOhad Ben-Cohen
The wl1271's irq line is completely controlled by the 1271 device, and the host does not not need to pull it up. While there's no functional effect, letting the host pull this line up is just redundant, and wastes power. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-14OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430Andy Green
This adapts the register offsets used to read the CPU DIE ID registers when run on 44XX so they match what is in the OMAP4430 Reference Manual page 269 Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-14omap4: mux: Remove duplicate mux modesTony Lindgren
Remove duplicate mux modes to make the binary smaller: text data bss dec hex filename 9378 24472 0 33850 843a mux44xx.o 9378 19104 0 28482 6f42 mux44xx.o Cc: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selectedTony Lindgren
Fix compile when CONFIG_OMAP_MUX is not selected Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap4: board-omap4panda: Initialise the serial padsR Sricharan
Use the mux framework to initialise the serial pads. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap3: board-3430sdp: Initialise the serial padsR Sricharan
Use the mux framework to initialise the serial pads. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap4: board-4430sdp: Initialise the serial padsR Sricharan
Use the mux framework to initialise the serial pads. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap2+: mux: Add macro for configuring static with omap_hwmod_mux_initTony Lindgren
Add macro for defining static pins in the board file. We can now start implementing pin multiplexing in the platform init code for devices that call omap_hwmod_mux_init. Currently that is only implemented for serial.c. Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap2+: mux: Remove the use of IDLE flagR Sricharan
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins dynamically. This can be simplified by using the enabled state variable of each pad. This also fixes the issue of the static pads not getting muxed after idling and disable/enable state transitions. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11omap2+: Add separate list for dynamic pads to muxTony Lindgren
This avoids going through the list unnecessarily when idling devices for runtime PM. Based on an earlier patch by sricharan <r.sricharan@ti.com>. Signed-off-by: sricharan <r.sricharan@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-11Merge branch 'for_2.6.39/pm-integration' of ↵Tony Lindgren
ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-linus
2011-03-11Merge branch 'integration-2.6.39-for-tony' of ↵Tony Lindgren
git://git.pwsan.com/linux-integration into omap-for-linus Conflicts: arch/arm/mach-omap2/pm34xx.c
2011-03-11perf: add OMAP support for the new power eventsJean Pihet
The patch adds the new power management trace points for the OMAP architecture. The trace points are for: - default idle handler. Since the cpuidle framework is instrumented in the generic way there is no need to add trace points in the OMAP specific cpuidle handler; - SoC clocks changes (enable, disable, set_rate), - power domain states: the desired target state and -if different- the actually hit state. Because of the generic nature of the changes, OMAP3 and OMAP4 are supported. Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS. Signed-off-by: Jean Pihet <j-pihet@ti.com> Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11OMAP4: Add IVA OPP enteries.Shweta Gulati
This Patch adds OPP enteries for IVA in OMAP4 OPP Table Tested on OMAP4430 SDP Board. Signed-off-by: Shweta Gulati <shweta.gulati@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11OMAP4: Update Voltage Rail Values for MPU, IVA and COREShweta Gulati
Update MPU, IVA and CORE voltage Rail values obtained from OMAP4430 Data Manual Operating Condition Addendum_v0.4. Tested on OMAP4430 SDP Board. Signed-off-by: Shweta Gulati <shweta.gulati@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11OMAP4: Enable 800 MHz and 1 GHz MPU-OPPShweta Gulati
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz. Enable them in OPP Table. For small minority of boards which use OMAP4430-800 MHz device OPP 1GHz is not supported, OPP 1GHz should be disabled from board file. Signed-off-by: Shweta Gulati <shweta.gulati@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11OMAP3+: OPP: Replace voltage values with MacrosVishwanath BS
Since all voltage data is now centralized in oppxxx_data.c, we can replace the values in the opp table with the macros used for voltage values. This will avoid opp table and voltage layer having conflicting values. Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com>
2011-03-11OMAP: Add gpio-keys support for OveroSteve Sakoman
This patch adds support for the standard push buttons available on Overo expansion boards. Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11OMAP: Add gpio-leds support for OveroSteve Sakoman
This patch adds support for the standard LEDs on the Overo COM and expansion boards Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11omap: overo: Add regulator for ads7846Steve Sakoman
The ads7846 driver now requires a regulator. This patch adds the necessary regulator to the overo board file. Without it, the following error occurs (and the touchscreen will not function): ads7846 spi1.0: unable to get regulator: -19 Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-28 15:37:17 +0000