| Age | Commit message (Collapse) | Author |
|---|
|
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
intoduce omap_mux_{read,write}
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
|
|
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates. This was a misapprehension. The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request. This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.
In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled. We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa). In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.
This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Sebastien Sabatier <s-sabatier1@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1). This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.
Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
|
|
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Juha Leppänen <juha_motorsportcom@luukku.com>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
MPU power domain bank 0 bits are displayed in position of bank 1
in PWRSTS and PREPWRSTS registers. So read them from correct
position
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
behind Kconfig
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers. This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state. This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on. Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM. At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders. Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.
This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.
Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Christophe Sucur <c-sucur@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Olof Johansson <olof@lixom.net>
|
|
IS_ERR returns only 1 or 0, and the functions return a negative error
in other cases anyways.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Replace some bare constants with power states.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
|
|
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Avoid cluttering the Kconfig space with debug options that are rarely
used. These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.
Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs. Convert most
of them to use tabs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
Device drivers and loadable modules should not be calling these
prm_* and cm_* functions, so stop exporting them. Only core code
and device driver integration code (in arch/arm/*omap*) should
call these functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The OMAP2 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device. This should save some memory. In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Nishanth Menon <nm@ti.com>
|
|
The OMAP3 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
clkdev_omap CPU flag
cpu_mask is reused in the OMAP2xxx clock code to match against both the
CPU-specific rate flags (e.g., RATE_IN_2420) and the OMAP clkdev integration
code CPU flags (e.g., CK_242X). This means that any patch that renumbers the
CK_* macros, as the next patch does, will probably break. This patch
separates the clkdev_omap and clksel_rate CPU type detection flags so
the CK_* macros can be renumbered freely.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
clock34xx.c contains some macros which probably belong in mach-omap2/sdrc.h.
Move those macros to mach-omap2/sdrc.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Similar to the previous patch, the APLL code relied on the presence of the
static struct clks in its own namespace. The APLL code didn't use them for
validation, however - it adjusted its own internal state depending on
the struct clk * that called it. Now that static struct clks are
leaving the clock24xx.c namespace, use a more durable method: split the
omap2_clk_fixed_enable() function into omap2_clk_apll96_enable() and
omap2_clk_apll54_enable(). They still share a disable function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
clock{,2xxx,3xxx}_data.c
Some parts of the clock code took advantage of the fact that the statically
allocated clock tree was in clock{,24xx,34xx}.c's local namespace to do some
extra argument checks. These are overzealous and are more difficult to
maintain when the clock tree is in a separate namespace, so, remove them.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
The upcoming new display subsystem driver is divided to two devices,
omapdss and omapfb, of which omapdss handles the actual hardware.
This patch adds a dummy omapdss platform device for the current omapfb
driver, which is then used to get the clocks. This will make it possible
for the current and the new display drivers to co-exist.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
SMS_ROT_* registers are used by VRFB rotation engine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (149 commits)
arm: omap: Add omap3_defconfig
AM35xx: Defconfig for AM3517 EVM board
AM35xx: Add support for AM3517 EVM board
omap: 3630sdp: defconfig creation
omap: 3630sdp: introduce 3630 sdp board support
omap3: Add defconfig for IGEP v2 board
omap3: Add minimal IGEP v2 support
omap3: Add CompuLab CM-T35 defconfig
omap3: Add CompuLab CM-T35 board support
omap3: rx51: Add wl1251 wlan driver support
omap3: rx51: Add SDRAM init
omap1: Add default kernel configuration for Herald
omap1: Add board support and LCD for HTC Herald
omap: zoom2: update defconfig for LL_DEBUG_NONE
omap: zoom3: defconfig creation
omap3: zoom: Introduce zoom3 board support
omap3: zoom: Drop i2c-1 speed to 2400
omap3: zoom: rename zoom2 name to generic zoom
omap3: zoom: split board file for software reuse
omap3evm: MIgrate to smsc911x ethernet driver
...
Fix trivial conflict (two unrelated config options added next to each
other) in arch/arm/mach-omap2/Makefile
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (272 commits)
Fix soc_common PCMCIA configuration
ARM: 5827/1: SA1100: h3100/h3600: emit messages on failed gpio_request
ARM: 5826/1: SA1100: h3100/h3600: always build htc-egpio driver
ARM: 5825/1: SA1100: h3600: update defconfig
ARM: 5824/1: SA1100: reuse h3600 PCMCIA driver on h3100
ARM: 5823/1: SA1100: h3100/h3600: add support for gpio-keys
ARM: 5822/1: SA1100: h3100/h3600: clean up #includes
ARM: 5821/1: SA1100: h3100/h3600: revise copyright boilerplates
ARM: 5820/1: SA1100: h3100/h3600: split h3600.c
ARM: 5819/1: SA1100: h3100/h3600: merge h3600.h and h3600_gpio.h into h3xxx.h
ARM: 5818/1: SA1100: h3100/h3600: drop old GPIO definitions
ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs
ARM: 5816/1: SA1100: h3600: remove IRQ_GPIO_* definitions
ARM: 5815/1: SA1100: h3100/h3600: remove now unused assign_h3600_egpio handlers
ARM: 5814/1: SA1100: h3100/h3600: convert all users of assign_h3600_egpio to gpiolib
ARM: 5813/1: SA1100: h3100/h3600: add htc-egpio driver
ARM: 5812/1: SA1100: h3100/h3600: separate machine-specific LCD helpers
ARM: 5811/2: pcmcia: convert sa1100_h3600 driver to gpiolib
ARM: 5799/1: SA1100: h3600: stop setting direction for LCD pins
ARM: 5798/1: SA1100: h3600: remove unused cruft from h3600.h
...
|
|
|
|
This enables on-chip tracing components found in omap3xxx.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch creates a minimal AM3517 EVM board support.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add 3630SDP board support
The board shares the same peripherals as a zoom2 main.
So reuse the peripheral file of zoom platform.
Peripheral zoom2 zoom3 sdp3630
---------------------------------------
Ethernet smsc smsc smc
NOR n/a n/a B
Onenand n/a n/a B
HDMI A A B (persent on different i2c)
NAND A A A (same nand)
SDRAM A A A (same sdram)
Keypad A A A (same twl)
Camera A A A (same sensor can be mounted)
LCD Display A A A (same wvga display)
OPPs A A A (same chip feature)
Audio A A A (same audio via twl5030)
OMAP3630 details can be found here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds basic support for CompuLab CM-T35 module.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
wl1251 is connected to the SPI bus in rx51, add support for this.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds board specific SDRAM init for RX51. This patch is a
collaboration of work from following people:
Juha Yrjola: Original code
Lauri Leukkunen: Port to RX51
Tero Kristo: Support for multiple OPP:s, merge of patches
Samu Onkalo: Fixed SDRAM parameters according to specs
Kalle Jokiniemi: A fix for rounding error
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Cc: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Cc: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Zoom3 is the next version of Zoom2 board.
There has been a silicon update from zoom2 to zoom3.
Zoom2 has OMAP34xx
Zoom3 has OMAP3630 [1]
Zoom3 = OMAP3630 SOM board [2] + same zoom2 main board [3] + same debugboard
Zoom3 has a SDRAM part from Hynix
Zoom2 had SDRAM part from micron
Hynix memory timings are contributed by:
Chalhoub, Nicole and Bour, Vincent
Reuse the zoom2 files as much for zoom3, as at board level,
there is no change at all.
References: (courtesy Nishant Menon)
[1] OMAP3630
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606
[2] SOM boards
http://logicpd.com/products/system-modules/texas-instruments-omap35x-som-lv
[3] Zoom2 boards
http://logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp
OMAP3630:
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
Cc: Vincent Bour <v-bour@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
