| Age | Commit message (Collapse) | Author |
|---|
|
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits)
[ARM] 5308/1: Fix Viper ISA IRQ handling
[ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error
[ARM] 5306/1: pxa: fix build error on CM-X270
[ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict
[ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check
[ARM] 5301/1: ARM: OMAP: Add missing irq defines
ARM: OMAP3: Add default kernel config for OMAP LDP
ARM: OMAP3: Add basic board support for OMAP LDP
ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)
ARM: OMAP3: Add Beagle defconfig
ARM: OMAP3: Add minimal Beagle board support
ARM: OMAP3: Add minimal omap3430 support
ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code
ARM: OMAP: Fixes to omap_mcbsp_request function
ARM: OMAP: Add support for OMAP2430 in McBSP
ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx
ARM: OMAP: Allocate McBSP devices dynamically
Fix sections for omap-mcbsp platform driver
[ARM] S3C24XX: Additional include moves
...
|
|
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
arch/arm/mach-versatile/core.c
|
|
Conflicts:
arch/arm/mach-pxa/Kconfig
arch/arm/mach-pxa/corgi.c
arch/arm/mach-pxa/include/mach/hardware.h
arch/arm/mach-pxa/spitz.c
|
|
Conflicts:
arch/arm/Kconfig
|
|
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Continue moving the include files into arch/arm
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
First move of items out of include/asm-arm/plat-s3c* to their
new homes under arch/arm/plat-s3c/include/plat and
arch/arm/plat-s3c24xx/include/plat directories.
Note, we have to create a dummy arch/arm/plat-s3c/Makefile to
allow us to add arch/arm/plat-s3c/include/plat to the path.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix the S3C2443 clock register definitions for selecting the EPLL
reference clock described by S3C2443_CLKSRC_EPLLREF.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
[ben-linux@fluff.org: minor description fixes]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Fix the following sparse errors in arch/arm/mach-s3c2410/nor-simtec.c:
53:27: warning: symbol 'simtec_nor_pdata' was not declared. Should it be static?
77:13: warning: symbol 'nor_simtec_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch removes CVS keywords that weren't updated for a long time.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
into for-rmk
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Any data being passed to s3c243xx_clock_register() can be
marked as __initdata as it is an array of pointers to
'struct clk' that are to be registered on initialisation.
The s3c243xx_clock_register function uses this array to
register clocks and does not require it to stay around
after exit.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Minor style fixes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Initialise the hardware register settings on boot, to allow the
device to function correctly.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch adds the configuration needed for the LCD display on the n30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for the Acer N35 and related devices.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for the LEDs on the Acer N30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for the GPIO buttons on the Acer N30.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for the USB D+ pull up on the Acer N30. This is needed
for the USB gadget to work properly.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Clean up some junk from the official kernel.
The compile-command is something that's only useful for me personally
and doesn't belong in the mainstream kernel.
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add tmp101 support via the new style I2C driver registration
on the VR1000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add i2c board intialisers to specify the I2C devices
attached on the Thorcom VR1000.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add i2c boardinfo for the connected i2c devices on the
Simtec Bast.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Move to using the physmap platform device code to attached NOR
flash on Simtec boards so that the old bast-flash driver can be
safely removed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Use the pata_platform driver to provide the IDE port
drivers on the Simntec BAST and Thorcom VR1000 machines
as a precursor to removing drivers/ide/arm/bast-ide.c
This will mean that the system will need SCSI and SCSI disc
support as a minimum, and any references to hdX will be
changed to sdX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Fix the flags entries for the DM9000 IRQ entries on both the
Simtec BAST and Thorcom VR1000 board. The current entries use
the IRQF_ flags, but we should be using the IORESOURCE_IRQ_
definitions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
PATCH FOLLOWS
KernelVersion: 2.6.26-rc5
|
|
Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the IRQF_TRIGGER_ type to the DM9000 IRQ resource
to stop the driver itself complaining it was not given
any flags to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix the pm sys device .name initialiser which was
missed when updating the last patch submission.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the TinCanTools Hammer board to list of supported machines in the
arch/arm/mach-s3c2410 directory, as well as a default config entry. the
mach-tct_hammer.c file initializes basic i/o, clocks, irqs, as well as
the mtd flash layout if enabled in the kernel configuration.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
All current Simtec designs source the DCLK outputs from
the UPLL. This means the DCLK's parent must be set to UPLL
so that anything enabling and disabling an UPLL sourced
clock does not shutdown the DCLK due to missing open counts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Change GPA21 to output over reset so that nRSTOUT is not
asserted whilst suspended.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
's3c2410', 'sa1100' and 'vfp' into devel
* at91: (24 commits)
[ARM] 4615/4: sam926[13]ek buttons updated
[ARM] 4765/1: [AT91] AT91CAP9A-DK board support
[ARM] 4764/1: [AT91] AT91CAP9 core support
[ARM] 4738/1: at91sam9261: Remove udc pullup enabling in board initialisation
[ARM] 4761/1: [AT91] Board-support for NEW_LEDs
[ARM] 4760/1: [AT91] SPI CS0 errata on AT91RM9200
[ARM] 4759/1: [AT91] Buttons on CSB300
[ARM] 4758/1: [AT91] LEDs
[ARM] 4757/1: [AT91] UART initialization
[ARM] 4756/1: [AT91] Makefile cleanup
[ARM] 4755/1: [AT91] NAND update
[ARM] 4754/1: [AT91] SSC library support
[ARM] 4753/1: [AT91] Use DMA_BIT_MASK
[ARM] 4752/1: [AT91] RTT, RTC and WDT peripherals on SAM9
[ARM] 4751/1: [AT91] ISI peripheral on SAM9263
[ARM] 4750/1: [AT91] STN LCD displays on SAM9261
[ARM] 4734/1: at91sam9263ek: include IRQ for Ethernet PHY
[ARM] 4646/1: AT91: configurable HZ, default to 128
[ARM] 4688/1: at91: speed-up irq processing
[ARM] 4657/1: AT91: Header definition update
...
* ep93xx:
[ARM] 4671/1: ep93xx: remove obsolete gpio_line_* operations
[ARM] 4670/1: ep93xx: implement IRQT_BOTHEDGE gpio irq sense type
[ARM] 4669/1: ep93xx: simplify GPIO code and cleanups
[ARM] 4668/1: ep93xx: implement new GPIO API
* iop:
[ARM] 4770/1: GLAN Tank: correct physmap_flash_data width field
[ARM] 4732/1: GLAN Tank: register rtc-rs5c372 i2c device
[ARM] 4708/1: iop: update defconfigs for 2.6.24
* kprobes:
ARM kprobes: let's enable it
ARM kprobes: special hook for the kprobes breakpoint handler
ARM kprobes: prevent some functions involved with kprobes from being probed
ARM kprobes: don't let a single-stepped stmdb corrupt the exception stack
ARM kprobes: add the kprobes hook to the page fault handler
ARM kprobes: core code
ARM kprobes: instruction single-stepping support
* ks8695:
[ARM] 4603/1: KS8695: debugfs interface to view pin state
[ARM] 4601/1: KS8695: PCI support
* misc:
[ARM] remove duplicate includes
[ARM] CONFIG_DEBUG_STACK_USAGE
[ARM] 4689/1: small comment wrap fix
[ARM] 4687/1: Trivial arch/arm/kernel/entry-common.S comment fix
[ARM] 4666/1: ixp4xx: fix sparse warnings in include/asm-arm/arch-ixp4xx/io.h
[ARM] remove reference to non-existent MTD_OBSOLETE_CHIPS
[SERIAL] 21285: Report baud rate back via termios
[ARM] Remove pointless casts from void pointers,
[ARM] Misc minor interrupt handler cleanups
[ARM] Remove at91_lcdc.h
[ARM] ARRAY_SIZE() cleanup
[ARM] Update mach-types
* msm:
[ARM] msm: dma support for MSM7X00A
[ARM] msm: board file for MACH_HALIBUT (QCT MSM7200A)
[ARM] msm: irq and timer support for ARCH_MSM7X00A
[ARM] msm: core platform support for ARCH_MSM7X00A
* s3c2410: (33 commits)
[ARM] 4795/1: S3C244X: Add armclk and setparent call
[ARM] 4794/1: S3C24XX: Comonise S3C2440 and S3C2442 clock code
[ARM] 4793/1: S3C24XX: Add IRQ->GPIO pin mapping function
[ARM] 4792/1: S3C24XX: Remove warnings from debug-macro.S
[ARM] 4791/1: S3C2412: Make fclk a parent of msysclk
[ARM] 4790/1: S3C2412: Fix parent selection for msysclk.
[ARM] 4789/1: S3C2412: Add missing CLKDIVN register values
[ARM] 4788/1: S3C24XX: Fix paramet to s3c2410_dma_ctrl if S3C2410_DMAF_AUTOSTART used.
[ARM] 4787/1: S3C24XX: s3c2410_dma_request() should return the allocated channel number
[ARM] 4786/1: S3C2412: Add SPI FIFO controll constants
[ARM] 4785/1: S3C24XX: Add _SHIFT definitions for S3C2410_BANKCON registers
[ARM] 4784/1: S3C24XX: Fix GPIO restore glitches
[ARM] 4783/1: S3C24XX: Add s3c2410_gpio_getpull()
[ARM] 4782/1: S3C24XX: Define FIQ_START for any FIQ users
[ARM] 4781/1: S3C24XX: DMA suspend and resume support
[ARM] 4780/1: S3C2412: Allow for seperate DMA channels for TX and RX
[ARM] 4779/1: S3C2412: Add s3c2412_gpio_set_sleepcfg() call
[ARM] 4778/1: S3C2412: Add armclk and init from DVS state
[ARM] 4777/1: S3C24XX: Ensure clk_set_rate() checks the set_rate method for the clk
[ARM] 4775/1: s3c2410: fix compilation error if only s3c2442 cpu is selected
...
* sa1100:
[ARM] sa1100: add clock source support
* vfp:
[ARM] 4584/2: ARMv7: Add Advanced SIMD (NEON) extension support
[ARM] 4583/1: ARMv7: Add VFPv3 support
[ARM] 4582/2: Add support for the common VFP subarchitecture
|
|
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
mostly in and around irq handlers.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes unused lcdcon2 and lcdcon3 register value
from the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds synchronization pulse lenght fields to
the s3c2410fb_display structure and makes use of them
in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds vertical margins values to all
s3c24xx platform.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes unused lcdcon3 register from the
s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
