Age | Commit message (Collapse) | Author |
|
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607fd20bed2f8c41fe22793386790a14aa
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111d3cde2607e0d04eb91da2f7a59b591
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU regulators would be processed
when DT is enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ST-Ericsson uses User Interface Boards to extend functionality of
some of their development boards. However, these aren't compatible
with all the supported boards found in Mainline (Snowball for
instance). This patch ensures that the UIBs are only probed on
boards which can actually support them. This in turn saves lots of
unnecessary error messages normally found in Snowball's boot log.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The final piece of the ab8500 puzzle. Here we prevent any of the ab8500-*
drivers from being registered from platform code when Device Tree is
enabled, as we expect DT do probe each of these individually. We also
provide the relevant compatible strings, so that DT knows which nodes
it needs to pay attention to during population.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The patch to disable SMSC911x registration was applied twice in the upstream
kernel by mistake. Git interpreted this as 'take the same entry from a
similar struct' which was close by. This was the wrong thing to do. This patch
rectifies this error and re-enables SMSC911x registration when Device Tree is
not enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now the DB8500 has Device Tree support it will be probed when the DT
is parsed, rendering the requirement for platform registration void.
This patch removes DB8500 PRCMU platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
During Device Tree enablement it is necessary to remove
<hw_component>_add_<device> calls one at at time, as and when particular
devices are DT enabled. This patch provides a temporary solution. Once
the new *of_init_devices function has been fully unpopulated it will be
removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
During Device Tree enablement it is necessary to remove snowball_<device>*
platform_data segments one at at time, as and when particular devices are
DT enabled. This patch provides a temporary solution. Once this new struct
is empty it will be removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
|
|
Pull crypto updates from Herbert Xu:
- New cipher/hash driver for ARM ux500.
- Code clean-up for aesni-intel.
- Misc fixes.
Fixed up conflicts in arch/arm/mach-ux500/devices-common.h, where quite
frankly some of it made no sense at all (the pull brought in a
declaration for the dbx500_add_platform_device_noirq() function, which
neither exists nor is used anywhere).
Also some trivial add-add context conflicts in the Kconfig file in
drivers/{char/hw_random,crypto}/
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni-intel - move more common code to ablk_init_common
crypto: aesni-intel - use crypto_[un]register_algs
crypto: ux500 - Cleanup hardware identification
crypto: ux500 - Update DMA handling for 3.4
mach-ux500: crypto - core support for CRYP/HASH module.
crypto: ux500 - Add driver for HASH hardware
crypto: ux500 - Add driver for CRYP hardware
hwrng: Kconfig - modify default state for atmel-rng driver
hwrng: omap - use devm_request_and_ioremap
crypto: crypto4xx - move up err_request_irq label
crypto, xor: Sanitize checksumming function selection output
crypto: caam - add backward compatible string sec4.0
|
|
Pull arm-soc power management changes from Olof Johansson:
"Power management changes here are mostly for the omap platform, but
also include cpuidle changes for ux500 and suspend/resume code for
mmp."
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
ARM: OMAP4: hwmod data: I2C: add flag for context restore
ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
ARM: OMAP2+: HDQ1W: add custom reset function
ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
ARM: OMAP2+: dmtimer: cleanup iclk usage
ARM: OMAP4+: Add prm and cm base init function.
ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
ARM: OMAP3: Fix CM register bit masks
ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
ARM: OMAP3: clock data: treat all AM35x devices the same
...
|
|
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
|
|
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
|
|
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
|
|
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
|
|
and 'versatile' into for-linus
|
|
ab8500-i2c is used as core code to register the ab8500 device.
After allocating ab8500 memory, it immediately calls into
ab8500-core where the real initialisation takes place. This
patch moves all core registration and memory allocation into
the true ab8500-core file and removes ab8500-i2c completely.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This adds the required platform data and calls to enable
the CRYP/HASH driver.
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Merge mainline to add prerequisite for ARM ux500 crypto support.
|
|
No point maintaining two branches for power management
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
* 'dt' of git://github.com/hzhuang1/linux:
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
Includes an update to v3-4-rc5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/mach-ux500/cache-l2x0.c
arch/arm/mach-ux500/clock.c
arch/arm/mach-ux500/cpu.c
arch/arm/mach-ux500/mbox-db5500.c
arch/arm/mach-ux500/platsmp.c
arch/arm/mach-ux500/timer.c
Resolve lots of identical conflicts between the removal of
u5500 and the addition of u8540.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into next/soc
* 'soc-core' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
+ renesas fixes and v3.4-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/pinctrl
* 'imx/pinctrl/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (290 commits)
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
tty: serial: imx: adopt pinctrl support
mmc: sdhci-imx-esdhc: adopt pinctrl support
ARM: imx6q: switch to use pinctrl subsystem
ARM: mxs: enable pinctrl dummy states
ARM: imx: enable pinctrl dummy states
+3.4-rc5 update
|
|
The MSP platform data callbacks use the old custom callbacks to
set the state of the pins, switch over to using pinctrl.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Alter the db8500_add_msp_i2s() calls to return a struct
platform_device * pointer, not an integer. We nee the pointer
to obtain a pinctrl handle.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
UART0 had a hack that enabled its pins on init and put it to
sleep on the exit callback. Replace this with the pinctrl calls
to do the same thing and update the runtime table with the two
apropriate states for runtime/active and idle.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
At the beginning of the first patch series I included the custom
ux500 pin control system to make sure I could eventually replace
it with the standard subsystem driver. So now that we've done so,
let's remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This converts the Ux500 family to use the pinctrl driver for
configuring pins.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into staging/cleanup
By Shawn Guo
via Shawn Guo
* 'clean/late_initcall_v2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
|
|
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds a driver for the ST-Ericsson ux500 hash hardware
module. The driver implements support for SHA-1 and SHA-2.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This adds a driver for the ST-Ericsson ux500 crypto hardware
module. It supports AES, DES and 3DES, the driver implements
support for AES-ECB,CBC and CTR.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds the cpuidle driver for the ux500 SoC.
The boards saves 12mA with these states. It is based on the latest
cpuidle consolidation from Robert Lee.
The cpu can go to retention only if the other core is in WFI.
If the other cpu is in WFI and we decoupled the gic from the cores,
then we have the guarantee, it won't be wake up.
It is up to the prcmu firmware to recouple the gic automatically
after the power state mode is selected.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In dbx500 based devices the PRCMU Timer 4 is used as a clocksource
and sched_clock. Here we fetch all necessary addressing information
required for correct PRCMU initialisation from the Device Tree
instead of using hard-coded values.
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To aid in sequential one-by-one Device Tree enablement, we split
cpu-db8500's platform_devs structure into normal platform boot, where
we leave all devices to be added in tact and a DT version where we
will remove the devices as they are DT enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch prevents i2c devices which are not present on the Snowball
low-cost development board from being registered. Devices such as;
tc3589x, bu1780 and lp5521 are present on other supported boards,
but are not located on Snowball.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This platform has been obsoleted and was only available inside of
ST-Ericsson, no users of this code are left in the world. This
deletes the core U5500 support entirely in the same manner as the
obsoleted U8500 silicon was previously deleted.
The cpu_is_u5500() macros that can read out the CPU ID is left
until the next kernel cycle, this makes it possible to merge
deletion of dependent drivers without breakage.
This also has the upside of removing the mailbox driver which was
our only driver that was outside the drivers/* hiearchy, now the
machine directory only handles machines and nothing else.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DB9540 ASIC has bigger PRCMU and PRCMU TCDM memories,
so create a separate mapping table for these.
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds support for the U9540 variant of the U8500 series. This
is an application processor without internal modem. This is the
most basic part with ASIC ID, CPU-related fixes, IRQ list, register
ranges, timer, UART, and L2 cache setup. This is based on a patch
by Michel Jaouen which was rewritten to fit with the latest 3.3
kernel.
ChangeLog v1->v2: deleted the irqs-db9540.h file since we expect to
migrate to using Device Tree for getting the IRQs to devices.
ChangeLog v2->v3: introduced a fixed virtual offset for the ROM
as suggested by Arnd Bergmann.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastien Pasdeloup <sebastien.pasdeloup-nonst@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Don't allow everybody to use a modem.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Create devices for the MSP-blocks (MSP0, MSP1, MSP2 and MSP3)
and associate it with the correct clocks in the clock-framework.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add irq domain support to the gpio-nomadik GPIO driver. This
enables its users to support dynamic IRQ assignment, which is
requried by Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This updates the Ux500 pin handling to take much more care when
applying pin settings for different platforms and peripherals.
This is an accumulation of a longer history of updates to the
MOP500 family pin file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|