| Age | Commit message (Collapse) | Author |
|---|
|
Move GPIO2 and GPIO3 to be registered from the core as this is
certainly available on Versatile AB as well, not just the PB.
GPIO2 is used for reading board status and GPIO3 is unused,
but it does not hurt to register it anyway.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From Peter Maydell:
These patches fix a number of issues with the PCI controller
code for mach-versatile:
(1) The irq mapping matched neither hardware nor QEMU; we correct
it to match the hardware, which means it will also work on recent
(1.5 or later) QEMU.
(2) The code was confused between the PCI I/O window (at 0x43000000)
and the first PCI memory window (at 0x44000000), which meant that
PCI devices using PCI PIO rather than MMIO didn't work. This is
fixed (and some variables/labels are renamed to avoid further
confusion in future).
(3) The SMAP register offsets were all off-by-four, though by
fluke this didn't actually have any ill effects.
All these changes have been tested on real hardware (PB926
plus the PCI backplane), as well as on QEMU. I have confirmed
that IRQs and PCI PIO and MMIO work OK.
PCI bus-master DMA doesn't seem to work on h/w -- as far as I can
tell the device is correctly managing to DMA to the right places
in memory, but every other 32 bit word is corrupt (at least judging
from rtl8139 debug dumps of the frames it's receiving). I'm not
sure what's going on here, but since this is disjoint from
the irq and I/O issues I don't think that applying the
patches that fix those should be stalled on trying to debug
DMA problems. (DMA works fine on QEMU, incidentally.)
* versatile/fixes:
ARM: PCI: versatile: Fix SMAP register offsets
ARM: PCI: versatile: Fix PCI I/O
ARM: PCI: versatile: Fix map_irq function to match hardware
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The SMAP register offsets in the versatile PCI controller code were
all off by four. (This didn't have any observable bad effects
because on this board PHYS_OFFSET is zero, and (a) writing zero to
the flags register at offset 0x10 has no effect and (b) the reset
value of the SMAP register is zero anyway, so failing to write SMAP2
didn't matter.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
The versatile PCI controller code was confused between the
PCI I/O window (at 0x43000000) and the first PCI memory
window (at 0x44000000). Pass the correct base address to
pci_remap_io() so that PCI I/O accesses work.
Since the first PCI memory window isn't used at all (it's
an odd size), rename the associated variables and labels
so that it's clear that it isn't related to the I/O window.
This has been tested and confirmed to fix PCI I/O accesses
both on physical PB926+PCI backplane hardware and on QEMU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
The PCI controller code for the Versatile board has never had the
correct IRQ mapping for hardware. For many years it had an odd
mapping ("all interrupts are int 27") which aligned with the
equivalent bug in QEMU. However as of commit 1bc39ac5dab265
the mapping changed and no longer matched either hardware or QEMU,
with the result that any PCI card beyond the first in QEMU would
not have functioning interrupts; for example a boot with a SCSI
controller would time out as follows:
------------
sym0: <895a> rev 0x0 at pci 0000:00:0d.0 irq 92
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
[...]
scsi 0:0:0:0: ABORT operation started
scsi 0:0:0:0: ABORT operation timed-out.
scsi 0:0:0:0: DEVICE RESET operation started
scsi 0:0:0:0: DEVICE RESET operation timed-out.
scsi 0:0:0:0: BUS RESET operation started
scsi 0:0:0:0: BUS RESET operation timed-out.
scsi 0:0:0:0: HOST RESET operation started
sym0: SCSI BUS has been reset
------------
Fix the mapping so that it matches real hardware (checked against the
schematics for PB926 and backplane, and tested against the hardware).
This allows PCI cards using interrupts to work on hardware for the
first time; this change will also work with QEMU 1.5 or later, where
the equivalent bugs in the modelling of the hardware have been fixed.
Although QEMU will attempt to autodetect whether the kernel is
expecting the long-standing "everything is int 27" mapping or the one
hardware has, for certainty we force it into "definitely behave like
hardware mode"; this will avoid unexpected surprises later if we
implement sparse irqs. This is harmless on hardware.
Thanks to Paul Gortmaker for bisecting the problem and finding an initial
solution, to Russell King for providing the correct interrupt mapping,
and to Guenter Roeck for providing an initial version of this patch
and prodding me into relocating the hardware and retesting everything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Now that the PL01X debug include can mostly stand alone without
requiring platforms to provide any macros, move it into the debug
directory so it can be directly included. This allows us to get rid of
a lot of debug-macros include files.
The autodetect case for Versatile Express and the ux500 are left alone;
these are more complicated implementations.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Move the definition of the UART register addresses out of the platform
specific header files into the Kconfig files.
Acked-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enable DT based init for the sp804 timers on versatile DT platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
|
|
The introduction of ARCH_MULTIPLATFORM changed
the default for nommu kernels from Versatile to
Integrator, which is less common, and does not
currently build for allnoconfig because that does
not select any of the CPUs.
This also ensures that at least one of the three
board files in versatile are enabled, which lets
us successfully build an allnoconfig kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
On NOMMU kernels, the io_desc variables are unused
because we don't use the MMU to remap the MMIO
areas.
Marking these variables as __maybe_unused easily
avoids the otherwise harmless warnings like
warning: 'versatile_io_desc' defined but not used
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
|
|
The PCI IRQs were regressing due to two things:
- The PCI glue layer was using an hard-coded IRQ 27 offset.
This caused the immediate regression.
- The SIC IRQ mask was inverted (i.e. a bit was indeed set to
one for each valid IRQ on the SIC, but accidentally inverted
in the init call). This has been around forever, but we have
been saved by some other forgiving code that would reserve
IRQ descriptors in this range, as the versatile is
non-sparse.
When the IRQs were bumped up 32 steps so as to avoid using IRQ
zero and avoid touching the 16 legacy IRQs, things broke.
Introduce an explicit valid mask for the IRQs that are active
on the PIC/SIC, and pass that. Use the BIT() macro from
<linux/bitops.h> to make sure we hit the right bits, readily
defined in <mach/platform.h>.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
The series cleans up ARCH_HAS_DECOMP_WDOG and arch_decomp_wdog which
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
* tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: samsung: remove unused arch_decomp_wdog() code
ARM: remove unused arch_decomp_wdog()
ARM: decompress: remove unused ARCH_HAS_DECOMP_WDOG
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
|
|
Clockevent cleanup series from Shawn Guo.
Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.
* clocksource/cleanup:
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
+ sync to Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-pxa/time.c
|
|
Now that we have VIC moved to drivers/irqchip and all VIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
|
|
Numerous includes of asm/hardware/vic.h aren't needed, so remove them.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-By: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Now that the VIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static. Move vic_handle_irq
to avoid a forward declaration.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
With ARCH_HAS_DECOMP_WDOG removed from arch/arm/boot/compressed/decompress.c,
all the arch_decomp_wdog() definition at platform level is unneeded.
Remmove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Versatile starts to register Linux IRQ numbers from offset 0
which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs
by 32 to get rid of the problem.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This moves the Versatile FPGA interrupt controller driver, used in
the Integrator/AP, Integrator/CP and some Versatile boards, out
of arch/arm/plat-versatile and down to drivers/irqchip where we
have consensus that such drivers belong. The header file is
consequently moved to <linux/platform_data/irq-versatile-fpga.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
|
|
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
|
|
into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Most platforms don't need mach/gpio.h and it prevents multi-platform
kernel images. Add CONFIG_NEED_MACH_GPIO_H and make platforns select it
if they need gpio.h. This is platforms that define __GPIOLIB_COMPLEX
or have lots of implicit includes pulled in by mach/gpio.h.
at91 and omap have gpio clean-up pending and can drop
CONFIG_NEED_MACH_GPIO_H once that is in.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This replaces the custom LED trigger code in mach-realview with
some overarching platform code for the plat-versatile family that
will lock down LEDs 2 thru 5 for CPU activity indication. The
day we have 8 core ARM systems the plat-versatile code will have
to become more elaborate.
Tested on RealView PB11MPCore by invoking four different CPU
hogs (yes > /dev/null&) and see the LEDs go on one at a time.
They all go off as the hogs are killed. Tested on the PB1176
as well - just one activity led (led 2) goes on and off with
CPU activity.
(bryan.wu@canonical.com: use ledtrig-cpu instead of ledtrig-arm-cpu)
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
|
|
Move versatile PCI to fixed i/o mapping and remove io.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
|
|
arch/arm/mach-versatile/pci.c: In function 'versatile_map_irq':
arch/arm/mach-versatile/pci.c:342: warning: unused variable 'devslot'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
With commit 4d5fc58dbe34b (ARM: remove bunch of now unused
mach/io.h files), the I/O space setup was completely broken on
versatile. This patch fixes that and prepares for further
I/O space clean-up.
I/O space handling on the versatile platform is currently
broken in multiple ways. Most importantly, the ports do
not get mapped into the virtual address space at all.
Also, there is some amount of confusion between PCI I/O
space and other statically mapped MMIO registers in the
platform code:
* The __io_address() macro that is used to access the
platform register maps to the same __io macro that gets
used for I/O space.
* The IO_SPACE_LIMIT is set to a value that is much larger
than the total available space.
* The I/O resource of the PCI bus is set to the physical
address of the mapping, which is way outside of the
actual I/O space limit as well as the address range that
gets decoded by traditional PCI cards.
* No attempt is made to stay outside of the ISA port range
that some device drivers try access.
* No resource gets requested as a child of ioport_resource,
but an IORESOURCE_IO type mapping gets requested
as a child of iomem_resource.
This patch attempts to correct all of the above. This makes
it possible to use virtio-pci based virtual devices as well
as actual PCI cards including those with legacy ISA port
ranges like VGA.
Some of the issues seem to be duplicated on other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[rob: update to 3.5-rc2 and io.h cleanup related changes]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
and 'versatile' into for-linus
|
|
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Most PCI implementations use the standard PCI swizzle function, which
handles the well defined behaviour of PCI-to-PCI bridges which can be
found on cards (eg, four port ethernet cards.)
Rather than having almost every platform specify the standard swizzle
function, make this the default when no swizzle function is supplied.
Therefore, a swizzle function only needs to be provided when there is
something exceptional which needs to be handled.
This gets rid of the swizzle initializer from 47 files, and leaves us
with just two platforms specifying a swizzle function: ARM Integrator
and Chalice CATS.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is at odds with the documentation in the file; it says pin 1 on
slots 24,25,26,27 map to IRQs 27,28,29,30, but the function will always
be entered with slot=0 due to the lack of swizzle function. Fix this
function to behave as the comments say, and use the standard PCI
swizzle.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The MMCI and PL022 SPI drivers sure need their platform data to
work on the Versatile as well. (This does not fix the auxdata for
MMCI instance mmc1 on the Versatile PB though.)
Cc: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This does two things to the FPGA IRQ controller in the versatile
family:
- Convert to MULTI_IRQ_HANDLER so we can drop the entry macro
from the Integrator. The C IRQ handler was inspired from
arch/arm/common/vic.c, recent bug discovered in this handler was
accounted for.
- Convert to using IRQ domains so we can get rid of the NO_IRQ
mess and proceed with device tree and such stuff.
As part of the exercise, bump all the low IRQ numbers on the
Integrator PIC to start from 1 rather than 0, since IRQ 0 is
now NO_IRQ. The Linux IRQ numbers are thus entirely decoupled
from the hardware IRQ numbers in this controller.
I was unable to split this patch. The main reason is the half-done
conversion to device tree in Versatile.
Tested on Integrator/AP and Integrator/CP.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
commit 9f786d033d025ab7d2c4d1b959aa81d935eb9e19
"arm/PCI: get rid of device resource fixups"
causes this failure on the versatile:
arch/arm/mach-versatile/pci.c: In function 'pci_versatile_setup_resources':
arch/arm/mach-versatile/pci.c:221: error: 'sys' undeclared (first use in this function)
because the versatile wasn't passing in the full struct pci_sys_data
but only the resource sub-field. Change it to pass in the full
struct so that sys will be in scope.
Reported-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: cleanups of io includes" from Olof Johansson:
"Rob Herring has done a sweeping change cleaning up all of the
mach/io.h includes, moving some of the oft-repeated macros to a common
location and removing a bunch of boiler plate. This is another step
closer to a common zImage for multiple platforms."
Fix up various fairly trivial conflicts (<mach/io.h> removal vs changes
around it, tegra localtimer.o is *still* gone, yadda-yadda).
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: tegra: Include assembler.h in sleep.S to fix build break
ARM: pxa: use common IOMEM definition
ARM: dma-mapping: convert ARCH_HAS_DMA_SET_COHERENT_MASK to kconfig symbol
ARM: __io abuse cleanup
ARM: create a common IOMEM definition
ARM: iop13xx: fix missing declaration of iop13xx_init_early
ARM: fix ioremap/iounmap for !CONFIG_MMU
ARM: kill off __mem_pci
ARM: remove bunch of now unused mach/io.h files
ARM: make mach/io.h include optional
ARM: clps711x: remove unneeded include of mach/io.h
ARM: dove: add explicit include of dove.h to addr-map.c
ARM: at91: add explicit include of hardware.h to uncompressor
ARM: ep93xx: clean-up mach/io.h
ARM: tegra: clean-up mach/io.h
ARM: orion5x: clean-up mach/io.h
ARM: davinci: remove unneeded mach/io.h include
[media] davinci: remove includes of mach/io.h
ARM: OMAP: Remove remaining includes for mach/io.h
ARM: msm: clean-up mach/io.h
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
|
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
|
|
Pull #1 ARM updates from Russell King:
"This one covers stuff which Arnd is waiting for me to push, as this is
shared between both our trees and probably other trees elsewhere.
Essentially, this contains:
- AMBA primecell device initializer updates - mostly shrinking the
size of the device declarations in platform code to something more
reasonable.
- Getting rid of the NO_IRQ crap from AMBA primecell stuff.
- Nicolas' idle cleanups. This in combination with the restart
cleanups from the last merge window results in a great many
mach/system.h files being deleted."
Yay: ~80 files, ~2000 lines deleted.
* 'for-armsoc' of git://git.linaro.org/people/rmk/linux-arm: (60 commits)
ARM: remove disable_fiq and arch_ret_to_user macros
ARM: make entry-macro.S depend on !MULTI_IRQ_HANDLER
ARM: rpc: make default fiq handler run-time installed
ARM: make arch_ret_to_user macro optional
ARM: amba: samsung: use common amba device initializers
ARM: amba: spear: use common amba device initializers
ARM: amba: nomadik: use common amba device initializers
ARM: amba: u300: use common amba device initializers
ARM: amba: lpc32xx: use common amba device initializers
ARM: amba: netx: use common amba device initializers
ARM: amba: bcmring: use common amba device initializers
ARM: amba: ep93xx: use common amba device initializers
ARM: amba: omap2: use common amba device initializers
ARM: amba: integrator: use common amba device initializers
ARM: amba: realview: get rid of private platform amba_device initializer
ARM: amba: versatile: get rid of private platform amba_device initializer
ARM: amba: vexpress: get rid of private platform amba_device initializer
ARM: amba: provide common initializers for static amba devices
ARM: amba: make use of -1 IRQs warn
ARM: amba: u300: get rid of NO_IRQ initializers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
|
|
Now that many platforms don't need mach/io.h, remove the unused ones.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
|
|
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
into for-armsoc
|
|
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch removes the simplistic implementation of irq_domains and enables
the powerpc infrastructure for all irq_domain users. The powerpc
infrastructure includes support for complex mappings between Linux and
hardware irq numbers, and can manage allocation of irq_descs.
This patch also converts the few users of irq_domain_add()/irq_domain_del()
to call irq_domain_add_legacy() instead.
v3: Fix bug that set up too many irqs in translation range.
v2: Fix removal of irq_alloc_descs() call in gic driver
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
|
