summaryrefslogtreecommitdiffstats
path: root/arch/arm/mm
AgeCommit message (Collapse)Author
2015-01-09ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile errorVictor Kamensky
In v3.19-rc3 tree when CONFIG_ARM_LPAE and CONFIG_DEBUG_RODATA are enabled image failed to compile with the following error: arch/arm/mm/init.c:661:14: error: ‘PMD_SECT_RDONLY’ undeclared here (not in a function) It seems that '80d6b0c ARM: mm: allow text and rodata sections to be read-only' and 'ded9477 ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE' commits crossed. 80d6b0c uses PMD_SECT_RDONLY macro but ded9477 renames it and uses software bits L_PMD_SECT_RDONLY instead. Fix is to use L_PMD_SECT_RDONLY instead PMD_SECT_RDONLY as ded9477 does in another places. Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-01-07ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem regionGrygorii Strashko
Now local variables kernel_x_start and kernel_x_end defined using 'unsigned long' type which is wrong because they represent physical memory range and will be calculated wrongly if LPAE is enabled. As result, all following code in map_lowmem() will not work correctly. For example, Keystone 2 boot is broken because kernel_x_start == 0x0000 0000 kernel_x_end == 0x0080 0000 instead of kernel_x_start == 0x0000 0008 0000 0000 kernel_x_end == 0x0000 0008 0080 0000 and as result whole low memory will be mapped with MT_MEMORY_RW permissions by code (start > kernel_x_end): } else if (start >= kernel_x_end) { map.pfn = __phys_to_pfn(start); map.virtual = __phys_to_virt(start); map.length = end - start; map.type = MT_MEMORY_RW; create_mapping(&map); } Hence, fix it by using phys_addr_t type for variables kernel_x_start and kernel_x_end. Tested-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2015-01-07ARM: 8249/1: mm: dump: don't skip regionsMark Rutland
Currently the arm page table dumping code starts dumping page tables from USER_PGTABLES_CEILING. This is unnecessary for skipping any entries related to userspace as the swapper_pg_dir does not contain such entries, and results in a couple of unfortuante side effects. Firstly, any kernel mappings which might exist below USER_PGTABLES_CEILING will not be accounted in the dump output. This masks any entries erroneously created below this address. Secondly, if the final page table entry walked is part of a valid mapping the page table dumping code will not log the region this entry is part of, as the final note_page call in walk_pgd will trigger an early return when 0 < USER_PGTABLES_CEILING. Luckily this isn't seen on contemporary systems as they typically don't have enough RAM to extend the linear mapping right to the end of the address space. Due to the way addr is constructed in the walk_* functions, it can never be less than USER_PGTABLES_CEILING when walking the page tables, so it is not necessary to avoid dereferencing invalid table addresses. The existing checks for st->current_prot and st->marker[1].start_address are sufficient to ensure we will not print and/or dereference garbage when trying to log information. This patch removes both problematic uses of USER_PGTABLES_CEILING from the arm page table dumping code, preventing both of these issues. We will now report any low mappings, and the final note_page call will not return early, ensuring all regions are logged. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Steve Capper <steve.capper@linaro.org> Cc: Kees Cook <keescook@chromium.org> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-12-16Merge tag 'iommu-config-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC/iommu configuration update from Arnd Bergmann: "The iomm-config branch contains work from Will Deacon, quoting his description: This series adds automatic IOMMU and DMA-mapping configuration for OF-based DMA masters described using the generic IOMMU devicetree bindings. Although there is plenty of future work around splitting up iommu_ops, adding default IOMMU domains and sorting out automatic IOMMU group creation for the platform_bus, this is already useful enough for people to port over their IOMMU drivers and start using the new probing infrastructure (indeed, Marek has patches queued for the Exynos IOMMU). The branch touches core ARM and IOMMU driver files, and the respective maintainers (Russell King and Joerg Roedel) agreed to have the contents merged through the arm-soc tree. The final version was ready just before the merge window, so we ended up delaying it a bit longer than the rest, but we don't expect to see regressions because this is just additional infrastructure that will get used in drivers starting in 3.20 but is unused so far" * tag 'iommu-config-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: iommu: store DT-probed IOMMU data privately arm: dma-mapping: plumb our iommu mapping ops into arch_setup_dma_ops arm: call iommu_init before of_platform_populate dma-mapping: detect and configure IOMMU in of_dma_configure iommu: fix initialization without 'add_device' callback iommu: provide helper function to configure an IOMMU for an of master iommu: add new iommu_ops callback for adding an OF device dma-mapping: replace set_arch_dma_coherent_ops with arch_setup_dma_ops iommu: provide early initialisation hook for IOMMU drivers
2014-12-12Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM updates from Russell King: "The major updates included in this update are: - Clang compatible stack pointer accesses by Behan Webster. - SA11x0 updates from Dmitry Eremin-Solenikov. - kgdb handling of breakpoints with read-only text/modules - Support for Privileged-no-execute feature on ARMv7 to prevent userspace code execution by the kernel. - AMBA primecell bus handling of irq-safe runtime PM - Unwinding support for memset/memzero/memmove/memcpy functions - VFP fixes for Krait CPUs and improvements in detecting the VFP architecture - A number of code cleanups (using pr_*, removing or reducing the severity of a couple of kernel messages, splitting ftrace asm code out to a separate file, etc.) - Add machine name to stack dump output" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits) ARM: 8247/2: pcmcia: sa1100: make use of device clock ARM: 8246/2: pcmcia: sa1111: provide device clock ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks ARM: 8244/1: fbdev: sa1100fb: make use of device clock ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device ARM: 8242/1: sa1100: add cpu clock ARM: 8221/1: PJ4: allow building in Thumb-2 mode ARM: 8234/1: sa1100: reorder IRQ handling code ARM: 8233/1: sa1100: switch to hwirq usage ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain ARM: 8231/1: sa1100: introduce irqdomains support ARM: 8230/1: sa1100: shift IRQs by one ARM: 8229/1: sa1100: replace irq numbers with names in irq driver ARM: 8228/1: sa1100: drop entry-macro.S ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER ARM: 8241/1: Update processor_modes for hyp and monitor mode ARM: 8240/1: MCPM: document mcpm_sync_init() ARM: 8239/1: Introduce {set,clear}_pte_bit ARM: 8238/1: mm: Refine set_memory_* functions ARM: 8237/1: fix flush_pfn_alias ...
2014-12-09Merge tag 'soc-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform changes from Arnd Bergmann: "New and updated SoC support, notable changes include: - bcm: brcmstb SMP support initial iproc/cygnus support - exynos: Exynos4415 SoC support PMU and suspend support for Exynos5420 PMU support for Exynos3250 pm related maintenance - imx: new LS1021A SoC support vybrid 610 global timer support - integrator: convert to using multiplatform configuration - mediatek: earlyprintk support for mt8127/mt8135 - meson: meson8 soc and l2 cache controller support - mvebu: Armada 38x CPU hotplug support drop support for prerelease Armada 375 Z1 stepping extended suspend support, now works on Armada 370/XP - omap: hwmod related maintenance prcm cleanup - pxa: initial pxa27x DT handling - rockchip: SMP support for rk3288 add cpu frequency scaling support - shmobile: r8a7740 power domain support various small restart, timer, pci apmu changes - sunxi: Allwinner A80 (sun9i) earlyprintk support - ux500: power domain support Overall, a significant chunk of changes, coming mostly from the usual suspects: omap, shmobile, samsung and mvebu, all of which already contain a lot of platform specific code in arch/arm" * tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits) ARM: mvebu: use the cpufreq-dt platform_data for independent clocks soc: integrator: Add terminating entry for integrator_cm_match ARM: mvebu: add SDRAM controller description for Armada XP ARM: mvebu: adjust mbus controller description on Armada 370/XP ARM: mvebu: add suspend/resume DT information for Armada XP GP ARM: mvebu: synchronize secondary CPU clocks on resume ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume ARM: mvebu: Armada XP GP specific suspend/resume code ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume ARM: mvebu: implement suspend/resume support for Armada XP clk: mvebu: add suspend/resume for gatable clocks bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration bus: mvebu-mbus: suspend/resume support clocksource: time-armada-370-xp: add suspend/resume support irqchip: armada-370-xp: Add suspend/resume support ARM: add lolevel debug support for asm9260 ARM: add mach-asm9260 ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf power: reset: imx-snvs-poweroff: add power off driver for i.mx6 ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A ...
2014-12-05Merge branch 'devel-stable' into for-nextRussell King
2014-12-05Merge branches 'fixes', 'misc', 'pm' and 'sa1100' into for-nextRussell King
2014-12-03ARM: 8238/1: mm: Refine set_memory_* functionsJungseung Lee
set_memory_* functions have same implementation except memory attribute. This patch makes to use common function for these, and pull out the functions into arch/arm/mm/pageattr.c like arm64 did. It will reduce code size and enhance the readability. Signed-off-by: Jungseung Lee <js07.lee@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-12-03ARM: 8237/1: fix flush_pfn_aliasJungseung Lee
L1_CACHE_BYTES could be larger than real L1 cache line size. In that case, flush_pfn_alias() would omit to flush last bytes as much as L1_CACHE_BYTES - real cache line size. So fix end address to "to + PAGE_SIZE - 1". The bottom bits of the address is LINELEN. that is ignored by mcrr. Signed-off-by: Jungseung Lee <js07.lee@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-12-03ARM: 8236/1: mm: fix discard_old_kernel_dataJungseung Lee
L1_CACHE_BYTES could be larger value than real L1 cache line size. In that case, discard_old_kernel_data() would omit to invalidate last bytes as much as L1_CACHE_BYTES - real cache line size. So fix end address to "to + PAGE_SIZE -1". The bottom bits of the address is LINELEN. that is ignored by mcrr. Signed-off-by: Jungseung Lee <js07.lee@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-12-03ARM: 8235/1: Support for the PXN CPU feature on ARMv7Jungseung Lee
Modern ARMv7-A/R cores optionally implement below new hardware feature: - PXN: Privileged execute-never(PXN) is a security feature. PXN bit determines whether the processor can execute software from the region. This is effective solution against ret2usr attack. On an implementation that does not include the LPAE, PXN is optionally supported. This patch set PXN bit on user page table for preventing user code execution with privilege mode. Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jungseung Lee <js07.lee@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-12-01arm: dma-mapping: plumb our iommu mapping ops into arch_setup_dma_opsWill Deacon
This patch plumbs the existing ARM IOMMU DMA infrastructure (which isn't actually called outside of a few drivers) into arch_setup_dma_ops, so that we can use IOMMUs for DMA transfers in a more generic fashion. Since this significantly complicates the arch_setup_dma_ops function, it is moved out of line into dma-mapping.c. If CONFIG_ARM_DMA_USE_IOMMU is not set, the iommu parameter is ignored and the normal ops are used instead. Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2014-11-28Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "Another round of relatively small ARM fixes. Thomas spotted that the strex backoff delay bit was a disable bit, so it needed to be clear for this to work. Vladimir spotted that using a restart block for the cache flush operation would return -EINTR, which userspace was not expecting. Dmitry spotted that the auxiliary control register accesses for Xscale were not correct" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8226/1: cacheflush: get rid of restarting block ARM: 8222/1: mvebu: enable strex backoff delay ARM: 8216/1: xscale: correct auxiliary register in suspend/resume
2014-11-27ARM: 8222/1: mvebu: enable strex backoff delayThomas Petazzoni
Under extremely rare conditions, in an MPCore node consisting of at least 3 CPUs, two CPUs trying to perform a STREX to data on the same shared cache line can enter a livelock situation. This patch enables the HW mechanism that overcomes the bug. This fixes the incorrect setup of the STREX backoff delay bit due to a wrong description in the specification. Note that enabling the STREX backoff delay mechanism is done by leaving the bit *cleared*, while the bit was currently being set by the proc-v7.S code. [Thomas: adapt to latest mainline, slightly reword the commit log, add stable markers.] Fixes: de4901933f6d ("arm: mm: Add support for PJ4B cpu and init routines") Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: Nadav Haklai <nadavh@marvell.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-21ARM: 8216/1: xscale: correct auxiliary register in suspend/resumeDmitry Eremin-Solenikov
According to the manuals I have, XScale auxiliary register should be reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to also use c1, c0, 1. The issue was primarily noticed thanks to qemu reporing "unsupported instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255 XScale Core manuals and in PXA270 and PXA320 Developers Guides. Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board. Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-21ARM: convert printk(KERN_* to pr_*Russell King
Convert many (but not all) printk(KERN_* to pr_* to simplify the code. We take the opportunity to join some printk lines together so we don't split the message across several lines, and we also add a few levels to some messages which were previously missing them. Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-21ARM: 8203/1: mm: try to re-use old ASID assignments following a rolloverWill Deacon
Rather than unconditionally allocating a fresh ASID to an mm from an older generation, attempt to re-use the old assignment where possible. This can bring performance benefits on systems where the ASID is used to tag things other than the TLB (e.g. branch prediction resources). Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-21ARM: 8196/1: vfp: Workaround bad MVFR1 register on some KraitsStephen Boyd
Certain versions of the Krait processor don't report that they support the fused multiply accumulate instruction via the MVFR1 register despite the fact that they actually do. Unfortunately we use this register to identify support for VFPv4. Override the hwcap on all Krait processors to indicate support for VFPv4 to workaround this. Tested-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-15Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "Two fixes this time, one to ensure that the kuser helper option depends on MMU as they aren't available for noMMU targets (and if the option is selected, we end up oopsing.) The second fix plugs a corner case with the decompressor, ensuring that the instruction stream can see the relocated code in every case on ARMv7 CPUs" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8198/1: make kuser helpers depend on MMU ARM: 8191/1: decompressor: ensure I-side picks up relocated code
2014-11-13ARM: 8198/1: make kuser helpers depend on MMUNathan Lynch
The kuser helpers page is not set up on non-MMU systems, so it does not make sense to allow CONFIG_KUSER_HELPERS to be enabled when CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in set_tls (used in execve and the arm_syscall trap handler): Unhandled exception: IPSR = 00000005 LR = fffffff1 CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216 task: 8b838000 ti: 8b82a000 task.ti: 8b82a000 PC is at flush_thread+0x32/0x40 LR is at flush_thread+0x21/0x40 pc : [<8f00157a>] lr : [<8f001569>] psr: 4100000b sp : 8b82be20 ip : 00000000 fp : 8b83c000 r10: 00000001 r9 : 88018c84 r8 : 8bb85000 r7 : 8b838000 r6 : 00000000 r5 : 8bb77400 r4 : 8b82a000 r3 : ffff0ff0 r2 : 8b82a000 r1 : 00000000 r0 : 88020354 xPSR: 4100000b CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216 [<8f002bc1>] (unwind_backtrace) from [<8f002033>] (show_stack+0xb/0xc) [<8f002033>] (show_stack) from [<8f00265b>] (__invalid_entry+0x4b/0x4c) As best I can tell this issue existed for the set_tls ARM syscall before commit fbfb872f5f41 "ARM: 8148/1: flush TLS and thumbee register state during exec" consolidated the TLS manipulation code into the set_tls helper function, but now that we're using it to flush register state during execve, !MMU users encounter the oops at the first exec. Prevent CONFIG_MMU=n configurations from enabling CONFIG_KUSER_HELPERS. Fixes: fbfb872f5f41 (ARM: 8148/1: flush TLS and thumbee register state during exec) Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com> Reported-by: Stefan Agner <stefan@agner.ch> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-11-11ARM: fix multiplatform allmodcompileLinus Walleij
Commit 68f3b875f7848f5304472184a4634148c5330cbd "ARM: integrator: make the Integrator multiplatform" broke allmodconfig like this: >> arch/arm/include/asm/cmpxchg.h:114:2: error: #error "SMP is not supported on this platform" (etc) This is due to the fact that as we turned on multiplatform for the Integrator, this enabled a lot of non-applicable CPU's to be selected for its multiplatform images, due to a lot of "depends on ARCH_INTEGRATOR" restrictions in arch/arm/mm/Kconfig for the different ARM CPU types. Fix this by restricting the CPU selections to respective multiplatform config, which now becomes a subset of the possible Integrator configurations, or alternatively the non-multiplatform config plus ARCH_INTEGRATOR, i.e.: if (!ARCH_MULTIPLATFORM || ARCH_MULTI_Vx) && (ARCH_INTEGRATOR || ARCH_FOO ...) Since the Integrator has been converted to multiplatform, this will often take the short form: if (ARCH_MULTI_Vx && ARCH_INTEGRATOR) If no other non-multiplatform platforms are elegible. Reported-by: Build bot for Mark Brown <broonie@kernel.org> Reported-by: Kbuild test robot <fengguang.wu@intel.com> Suggested-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2014-11-03Merge tag 'ronx-next' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into devel-stable generic fixmaps ARM support for CONFIG_DEBUG_RODATA
2014-11-02Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: - add the new bpf syscall to ARM. - drop a redundant return statement in __iommu_alloc_remap() - fix a performance issue noticed by Thomas Petazzoni with kmap_atomic(). - fix an issue with the L2 cache OF parsing code which caused it to incorrectly print warnings on each boot, and make the warning text more consistent with the rest of the code * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn() ARM: 8183/1: l2c: Improve l2c310_of_parse() error message ARM: 8181/1: Drop extra return statement ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int' ARM: enable bpf syscall
2014-10-29ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()Thomas Petazzoni
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a very significant drop in networking performance. The test were conducted on an OpenBlocks A7 board. Without this patch, the outgoing performance measured with iperf are: - highmem OFF, TSO OFF 544 Mbit/s - highmem OFF, TSO ON 942 Mbit/s - highmem ON, TSO OFF 306 Mbit/s - highmem ON, TSO ON 246 Mbit/s On this Kirkwood platform, the L2 cache is a Feroceon cache, and with this cache, all the range operations have to be done on virtual addresses and not physical addresses. Therefore, whenever CONFIG_HIGHMEM is enabled, the cache maintenance operations call kmap_atomic_pfn() and kunmap_atomic(). However, kmap_atomic_pfn() does not implement the same fast path for non-highmem pages as the one implemented in kmap_atomic(), and this is one of the reason for the performance drop. While this patch does not fully restore the performances, it clearly improves them a lot: without patch with patch - highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s - highmem ON, TSO ON 246 Mbit/s 434 Mbit/s We're still far from the !CONFIG_HIGHMEM performances, but it does improve a bit the situation. Thanks a lot to Ezequiel Garcia and Gregory Clement for all the testing work around this topic. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-29ARM: 8183/1: l2c: Improve l2c310_of_parse() error messageFabio Estevam
Russell King suggested [1]: "I'd ask for one change. Please make all these messages start with "L2C-310 OF" not "PL310 OF:". The device is described in ARM documentation as a L2C-310 not PL310. (Also note the : is dropped too - most of the other messages don't have the : either.) The: "PL310 OF: cache setting yield illegal associativity PL310 OF: -1073346556 calculated, only 8 and 16 legal" message could also be changed to something like: "L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn" [1] http://www.spinics.net/lists/arm-kernel/msg372776.html Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-29ARM: 8181/1: Drop extra return statementLaura Abbott
Commit 513510ddba9650fc7da456eefeb0ead7632324f6 (common: dma-mapping: introduce common remapping functions) managed to end up with an extra return statement from the original patch. Drop it. Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-29ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'Fabio Estevam
Since commit f3354ab67476dc80 ("ARM: 8169/1: l2c: parse cache properties from ePAPR definitions") the following error is seen on imx6q: [ 0.000000] PL310 OF: cache setting yield illegal associativity [ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized. To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-28Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "A couple of ARM fixes. We fix some printk formats for ptrdiff_t quantities which cause GCC 4.9 to complain, and we also blacklist known buggy GCC 4.8.x compilers as their miscompilation is serious enough to cause filesystem corruption, even through many distros have fixed their versions" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: fix some printk formats ARM: Blacklist GCC 4.8.0 to GCC 4.8.2 - PR58854
2014-10-21ARM: fix some printk formatsRussell King
GCC 4.9 complains if we take the difference of two pointers, and it's printed with "%d". Fix this by using the proper flag - "t" for ptrdiff_t. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-16ARM: mm: allow text and rodata sections to be read-onlyKees Cook
This introduces CONFIG_DEBUG_RODATA, making kernel text and rodata read-only. Additionally, this splits rodata from text so that rodata can also be NX, which may lead to wasted memory when aligning to SECTION_SIZE. The read-only areas are made writable during ftrace updates and kexec. Signed-off-by: Kees Cook <keescook@chromium.org> Tested-by: Laura Abbott <lauraa@codeaurora.org> Acked-by: Nicolas Pitre <nico@linaro.org>
2014-10-16ARM: mm: allow non-text sections to be non-executableKees Cook
Adds CONFIG_ARM_KERNMEM_PERMS to separate the kernel memory regions into section-sized areas that can have different permisions. Performs the NX permission changes during free_initmem, so that init memory can be reclaimed. This uses section size instead of PMD size to reduce memory lost to padding on non-LPAE systems. Based on work by Brad Spengler, Larry Bassel, and Laura Abbott. Signed-off-by: Kees Cook <keescook@chromium.org> Tested-by: Laura Abbott <lauraa@codeaurora.org> Acked-by: Nicolas Pitre <nico@linaro.org>
2014-10-16arm: fixmap: implement __set_fixmap()Kees Cook
This is used from set_fixmap() and clear_fixmap() via asm-generic/fixmap.h. Also makes sure that the fixmap allocation fits into the expected range. Based on patch by Rabin Vincent. Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Rabin Vincent <rabin@rab.in> Acked-by: Nicolas Pitre <nico@linaro.org>
2014-10-16ARM: expand fixmap region to 3MBRob Herring
With commit a05e54c103b0 ("ARM: 8031/2: change fixmap mapping region to support 32 CPUs"), the fixmap region was expanded to 2MB, but it precluded any other uses of the fixmap region. In order to support other uses the fixmap region needs to be expanded beyond 2MB. Fortunately, the adjacent 1MB range 0xffe00000-0xfff00000 is availabe. Remove fixmap_page_table ptr and lookup the page table via the virtual address so that the fixmap region can span more that one pmd. The 2nd pmd is already created since it is shared with the vector page. Signed-off-by: Rob Herring <robh@kernel.org> [kees: fixed CONFIG_DEBUG_HIGHMEM get_fixmap() calls] [kees: moved pte allocation outside of CONFIG_HIGHMEM] Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Nicolas Pitre <nico@linaro.org>
2014-10-16arm: use generic fixmap.hMark Salter
ARM is different from other architectures in that fixmap pages are indexed with a positive offset from FIXADDR_START. Other architectures index with a negative offset from FIXADDR_TOP. In order to use the generic fixmap.h definitions, this patch redefines FIXADDR_TOP to be inclusive of the useable range. That is, FIXADDR_TOP is the virtual address of the topmost fixed page. The newly defined FIXADDR_END is the first virtual address past the fixed mappings. Signed-off-by: Mark Salter <msalter@redhat.com> Reviewed-by: Doug Anderson <dianders@chromium.org> [kees: update for a05e54c103b0 ("ARM: 8031/2: change fixmap ...")] Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Laura Abbott <lauraa@codeaurora.org> Cc: Rob Herring <robh@kernel.org> Acked-by: Nicolas Pitre <nico@linaro.org>
2014-10-14Merge tag 'samsung-fixes' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes Merge "Samsung fixes for v3.18" from Kukjin Kim: - fix ifdef around cpu_*_do_[suspend, resume] ops to check CONFIG_ARM_CPU_SUSPEND and not CONFIG_PM_SLEEP - fix exynos_defconfig build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n - fix enabling Samsung PM debug functionality due to recently merged patches and previous merge conflicts - fix pull-up setting in sd4_width8 pin group for exynos4x12 * tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n ARM: SAMSUNG: Restore Samsung PM Debug functionality ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12 Signed-off-by: Olof Johansson <olof@lixom.net>
2014-10-09arm: mm: enable RCU fast_gupSteve Capper
Activate the RCU fast_gup for ARM. We also need to force THP splits to broadcast an IPI s.t. we block in the fast_gup page walker. As THP splits are comparatively rare, this should not lead to a noticeable performance degradation. Some pre-requisite functions pud_write and pud_page are also added. Signed-off-by: Steve Capper <steve.capper@linaro.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Dann Frazier <dann.frazier@canonical.com> Cc: Hugh Dickins <hughd@google.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Will Deacon <will.deacon@arm.com> Cc: Christoffer Dall <christoffer.dall@linaro.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-09ARM: mm: don't limit default CMA region only to low memoryMarek Szyprowski
DMA-mapping supports CMA regions places either in low or high memory, so there is no longer needed to limit default CMA regions only to low memory. The real limit is still defined by architecture specific DMA limit. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: Daniel Drake <drake@endlessm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-09arm: use genalloc for the atomic poolLaura Abbott
ARM currently uses a bitmap for tracking atomic allocations. genalloc already handles this type of memory pool allocation so switch to using that instead. Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Riley <davidriley@chromium.org> Cc: Olof Johansson <olof@lixom.net> Cc: Ritesh Harjain <ritesh.harjani@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-09common: dma-mapping: introduce common remapping functionsLaura Abbott
For architectures without coherent DMA, memory for DMA may need to be remapped with coherent attributes. Factor out the the remapping code from arm and put it in a common location to reduce code duplication. As part of this, the arm APIs are now migrated away from ioremap_page_range to the common APIs which use map_vm_area for remapping. This should be an equivalent change and using map_vm_area is more correct as ioremap_page_range is intended to bring in io addresses into the cpu space and not regular kernel managed memory. Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Riley <davidriley@chromium.org> Cc: Olof Johansson <olof@lixom.net> Cc: Ritesh Harjain <ritesh.harjani@gmail.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Will Deacon <will.deacon@arm.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Laura Abbott <lauraa@codeaurora.org> Cc: Mitchel Humpherys <mitchelh@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-10-02Merge branches 'fiq' (early part), 'fixes', 'l2c' (early part) and 'misc' ↵Russell King
into for-next
2014-10-02ARM: 8167/1: extend the reserved memory for initrd to be page alignedYalin Wang
This patch extends the start and end address of initrd to be page aligned, so that we can free all memory including the un-page aligned head or tail page of initrd, if the start or end address of initrd are not page aligned, the page can't be freed by free_initrd_mem() function. Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-10-02ARM: 8169/1: l2c: parse cache properties from ePAPR definitionsLinus Walleij
When both 'cache-size' and 'cache-sets' are specified for a L2 cache controller node, parse those properties and set up the set size based on which type of L2 cache controller we are using. Update the L2 cache controller Device Tree binding with the optional 'cache-size', 'cache-sets', 'cache-block-size' and 'cache-line-size' properties. These come from the ePAPR specification. Using the cache size, number of sets and cache line size we can calculate desired associativity of the L2 cache. This is done by the calculation: set size = cache size / sets ways = set size / line size way size = cache size / ways = sets * line size associativity = cache size / way size Example output from the PB1176 DT that look like this: L2: l2-cache { compatible = "arm,l220-cache"; (...) arm,override-auxreg; cache-size = <131072>; // 128kB cache-sets = <512>; cache-line-size = <32>; }; Ends up like this: L2C OF: override cache size: 131072 bytes (128KB) L2C OF: override line size: 32 bytes L2C OF: override way size: 16384 bytes (16KB) L2C OF: override associativity: 8 L2C: DT/platform modifies aux control register: 0x02020fff -> 0x02030fff L2C-220 cache controller enabled, 8 ways, 128 kB L2C-220: CACHE_ID 0x41000486, AUX_CTRL 0x06030fff Which is consistent with the value earlier hardcoded for the PB1176 platform. This patch is an extended version based on the initial patch by Florian Fainelli. Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-09-26ARM: 8152/1: Convert pr_warning to pr_warnJoe Perches
Use the more common pr_warn. Other miscellanea: o Coalesce formats o Realign arguments Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-09-25ARM: 8165/1: alignment: don't break misaligned NEON load/storeRobin Murphy
The alignment fixup incorrectly decodes faulting ARM VLDn/VSTn instructions (where the optional alignment hint is given but incorrect) as LDR/STR, leading to register corruption. Detect these and correctly treat them as unhandled, so that userspace gets the fault it expects. Reported-by: Simon Hosie <simon.hosie@arm.com> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-09-25ARM: 8164/1: mm: clear SCTLR.HA instead of setting it for LPAEWill Deacon
SCTLR.HA (hardware access flag) is deprecated and not actually implemented by any CPUs. Furthermore, it can confuse cr_alignment checks where the whole value of SCTLR is compared against the value sitting in the hardware, since the bit is actually RAZ/WI and will not match the saved cr_alignment value. Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-09-24ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] opsBartlomiej Zolnierkiewicz
Ifdef around cpu_\name\()_do_suspend and cpu_\name\()_do_resume ops in proc-macros.S should check for CONFIG_ARM_CPU_SUSPEND and not CONFIG_PM_SLEEP. Fix it. [ Please note that cpu_v7_do_[suspend,resume] code in proc-v7.S already correctly checks for CONFIG_ARM_CPU_SUSPEND, same is true for functions for other architectures. ] This fix is needed for decoupling suspend/resume and advanced cpuidle support on Exynos platform (next patch fixes build for config with CONFIG_PM_SLEEP=n and CONFIG_ARM_EXYNOS_CPUIDLE=y). If this fix is not present then the following OOPS happens on the first attempt to go into advanced cpuidle mode (AFTR): [ 22.244143] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 22.250759] pgd = c0004000 [ 22.253445] [00000000] *pgd=00000000 [ 22.257012] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM [ 22.262906] Modules linked in: [ 22.265949] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.16.0-next-20140811-dirty #730 [ 22.273757] task: c05dce68 ti: c05d2000 task.ti: c05d2000 [ 22.279139] PC is at 0x0 [ 22.281661] LR is at __cpu_suspend_save+0x4c/0xa8 [ 22.286344] pc : [<00000000>] lr : [<c00125e0>] psr: a0000093 [ 22.286344] sp : c05d3ef4 ip : c05da414 fp : 00000001 [ 22.297799] r10: c05da414 r9 : c0609cb0 r8 : 0000000f [ 22.303008] r7 : c05da444 r6 : 00000038 r5 : ea802c00 r4 : c05d3f14 [ 22.309517] r3 : 00000000 r2 : c05d3f4c r1 : 00000038 r0 : c05d3f20 [ 22.316029] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel [ 22.323406] Control: 10c5387d Table: 69d5404a DAC: 00000015 [ 22.329135] Process swapper/0 (pid: 0, stack limit = 0xc05d2240) [ 22.335124] Stack: (0xc05d3ef4 to 0xc05d4000) [ 22.339466] 3ee0: ea802c00 00000038 c05d3f4c [ 22.347626] 3f00: 00000000 00000007 c00123bc 00000000 c001d468 6a888000 c05d3f4c 80000000 [ 22.355785] 3f20: 00000007 c003d3a0 0000193d eaf9dde4 eaf9dde4 c02ef0c8 c000969c fffffffe [ 22.363944] 3f40: 00000000 c0037b54 eaf9dbb8 e9d1a380 00000000 c001d468 c0609cb0 00000000 [ 22.372103] 3f60: c0609cb0 c061649e 00000001 c001250c eaf9dbb8 00000001 c0609cb0 c001d618 [ 22.380262] 3f80: c001d5d0 c02ef56c 2d9d2e1e 00000005 eaf9dbb8 c02edcc4 2d9d2e1e 00000005 [ 22.388421] 3fa0: c040446c c05da4ec c040446c eaf9dbb8 c05cfbb0 c004c580 c05dce68 c05b3ae8 [ 22.396580] 3fc0: 00000000 c058bb24 ffffffff ffffffff c058b5e4 00000000 00000000 c05b3ae8 [ 22.404740] 3fe0: c0616994 c05da47c c05b3ae4 c05ddeec 4000406a 40008074 00000000 00000000 [ 22.412909] [<c00125e0>] (__cpu_suspend_save) from [<c00123bc>] (__cpu_suspend+0x5c/0x70) [ 22.421074] [<c00123bc>] (__cpu_suspend) from [<c05d3f4c>] (init_thread_union+0x1f4c/0x2000) [ 22.429479] Code: bad PC value [ 22.432518] ---[ end trace fb90ebf4217d0ad9 ]--- [ 22.437116] Kernel panic - not syncing: Attempted to kill the idle task! [ 22.443800] Rebooting in 5 seconds.. This patch has been tested on Exynos4210 based Origen board. Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-09-12ARM: 8138/1: drop ISAR0 workaround for B15Brian Norris
The Brahma-B15's ISAR0 correcty advertises UDIV/SDIV support in both ARM and Thumb2 modes (CPUID_EXT_ISAR0=02101110), so we don't need to manually apply this hwcap. The code in question actually predates the following commit, which made our hwcaps unnecessary: commit 8164f7af88d9ad3a757bd14f634b23997ee77f6b Author: Stephen Boyd <sboyd@codeaurora.org> Date: Mon Mar 18 19:44:15 2013 +0100 ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-09-02ARM: 8132/1: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSETKonstantin Khlebnikov
ARM: LPAE: drop wrong carry flag correction after adding TTBR1_OFFSET In commit 7fb00c2fca4b6c58be521eb3676cf4b4ba8dde3b ("ARM: 8114/1: LPAE: load upper bits of early TTBR0/TTBR1") part which fixes carrying in adding TTBR1_OFFSET to TTRR1 was wrong: addls ttbr1, ttbr1, #TTBR1_OFFSET adcls tmp, tmp, #0 addls doesn't update flags, adcls adds carry from cmp above: cmp ttbr1, tmp @ PHYS_OFFSET > PAGE_OFFSET? Condition 'ls' means carry flag is clear or zero flag is set, thus only one case is affected: when PHYS_OFFSET == PAGE_OFFSET. It seems safer to remove this fixup. Bug is here for ages and nobody complained. Let's fix it separately. Reported-and-Tested-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2014-08-27ARM: 8128/1: abort: don't clear the exclusive monitorsMark Rutland
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors upon entry to the kernel, but this is redundant: - We clear the monitors on every exception return since commit 200b812d0084 ("Clear the exclusive monitor when returning from an exception"), so this is not necessary to ensure the monitors are cleared before returning from a fault handler. - Any dummy STREX will target a temporary scratch area in memory, and may succeed or fail without corrupting useful data. Its status value will not be used. - Any other STREX in the kernel must be preceded by an LDREX, which will initialise the monitors consistently and will not depend on the earlier state of the monitors. Therefore we have no reason to care about the initial state of the exclusive monitors when a data abort is taken, and clearing the monitors prior to exception return (as we already do) is sufficient. This patch removes the redundant clearing of the exclusive monitors from the early abort handlers. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-11 00:09:04 +0000