| Age | Commit message (Collapse) | Author |
|---|
|
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.
This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).
This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
refactored printing of the kernel warning:
"orion_mpp_conf: requested MPP%u config unavailable on this hardware\n"
which is not to be printed in case of variant_mask = 0 (unknown variant).
This check should be performed using a logical AND (&&) as opposed
to a bitwise AND (&).
Otherwise, test would fail (and message would not be printed) if
variant_mask != 1
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The clockevent core is able to figure out the best mult and shift,
calculate min_delta_ns and max_delta_ns, with the necessary info passed
into clockevents_config_and_register(). Use this combined configure
and register function where possible to make the codes less error prone
and gain some positive diff stat.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brown <davidb@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Barry Song <baohua.song@csr.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
|
|
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Add hardware I/O coherency support for Armada 370/XP
The purpose of this patch set is to add hardware I/O Coherency support
for Armada 370 and Armada XP. Theses SoCs come with an unit called
coherency fabric. A beginning of the support for this unit have been
introduced with the SMP patch set. This series extend this support:
the coherency fabric unit allows to use the Armada XP and the Armada
370 as nearly coherent architectures.
The third patches enables this new feature and register our own set
of DMA ops, to benefit this hardware enhancement.
The first patches exports a dma operation function needed to register
our own set of dma ops.
The second patch introduces a new flag for the address decoding
configuration in order to be able to set the memory windows as
shared memory.
|
|
Recent SoC such as Armada 370/XP came with the possibility to deal
with the I/O coherency by hardware. In this case the transaction
attribute of the window must be flagged as "Shared transaction". Once
this flag is set, then the transactions will be forced to be sent
through the coherency block, in other case transaction is driven
directly to DRAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Yehuda Yitschak <yehuday@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
The pool_size is always PAGE_SIZE, and since it is a software
configuration paramter (and not a hardware description parameter), we
cannot make it part of the Device Tree binding, so we'd better remove
it from the platform_data as well.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
There is no need for the platform_data to give this ID, it is simply
the channel number, so we can compute it inside the driver when
registering the channels.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
Since we got rid of the per-XOR channel 'mv_xor' driver, now the
per-XOR engine driver that used to be called 'mv_xor_shared' can
simply be named 'mv_xor'.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
'struct mv_xor_shared_platform_data' used to be the platform_data
structure for the 'mv_xor_shared', but this driver is going to be
renamed simply 'mv_xor', so also rename its platform_data structure
accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
mv_xor_platform_data used to be the platform_data structure associated
to the 'mv_xor' driver. This driver no longer exists, and this data
structure really contains the properties of each XOR channel part of a
given XOR engine. Therefore 'struct mv_xor_channel_data' is a more
appropriate name.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
This member of the platform_data structure is no longer used, so get
rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
Now that xor0 and xor1 are registered in a single driver manner, the
orion_xor_init_channels() function has become useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
driver
Instead of registering one 'mv_xor_shared' device for the XOR engine,
and then two 'mv_xor' devices for the XOR channels, pass the channels
properties as platform_data for the main 'mv_xor_shared' device.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
driver
Instead of registering one 'mv_xor_shared' device for the XOR engine,
and then two 'mv_xor' devices for the XOR channels, pass the channels
properties as platform_data for the main 'mv_xor_shared' device.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Moving ARCH_MVEBU for multi-platform support caused several breakages in
recently added addr-map and pinctrl support for mvebu. This adds the
necessary selects and include paths to fix the build.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.infradead.org/users/jcooper/linux into late/kirkwood
* 'kirkwood/addr_decode' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: add address decoding controller to the DT
arm: mvebu: add basic address decoding support to Armada 370/XP
arm: plat-orion: make bridge_virt_base non-const to support DT use case
arm: plat-orion: introduce PLAT_ORION_LEGACY hidden config option
arm: plat-orion: use void __iomem pointers for addr-map functions
arm: plat-orion: use void __iomem pointers for time functions
arm: plat-orion: use void __iomem pointers for MPP functions
arm: plat-orion: use void __iomem pointers for UART registration functions
arm: mach-mvebu: use IOMEM() for base address definitions
arm: mach-orion5x: use IOMEM() for base address definitions
arm: mach-mv78xx0: use IOMEM() for base address definitions
arm: mach-kirkwood: use IOMEM() for base address definitions
arm: mach-dove: use IOMEM() for base address definitions
arm: mach-orion5x: use plus instead of or for address definitions
arm: mach-mv78xx0: use plus instead of or for address definitions
arm: mach-kirkwood: use plus instead of or for address definitions
arm: mach-dove: use plus instead of or for address definitions
This branch had quite a few conflicts, in particular with the PCI static
map rework from Rob Herring, and a few other context conflicts due to
changes in Kconfig, etc.
I fixed up conflicts in:
arch/arm/Kconfig
arch/arm/mach-dove/common.c
arch/arm/mach-dove/include/mach/dove.h
arch/arm/mach-kirkwood/common.c
arch/arm/mach-kirkwood/include/mach/kirkwood.h
arch/arm/mach-mv78xx0/common.c
arch/arm/mach-mv78xx0/include/mach/mv78xx0.h
arch/arm/mach-orion5x/common.c
arch/arm/mach-orion5x/include/mach/orion5x.h
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* multiplatform/platform-data:
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: nomadik: move platform_data definitions
ARM: w90x900: move platform_data definitions
ARM: vt8500: move platform_data definitions
ARM: tegra: move sdhci platform_data definition
ARM: sa1100: move platform_data definitions
ARM: pxa: move platform_data definitions
ARM: netx: move platform_data definitions
ARM: msm: move platform_data definitions
ARM: imx: move platform_data definitions
ARM: ep93xx: move platform_data definitions
ARM: davinci: move platform_data definitions
ARM: at91: move platform_data definitions
Conflicts due to removed files:
arch/arm/mach-tegra/board-harmony.c
arch/arm/mach-tegra/board-trimslice.c
Conflicts due to code removal:
arch/arm/mach-tegra/board-paz00.c
Context conflicts in:
drivers/mmc/host/sdhci-tegra.c
drivers/net/irda/pxaficp_ir.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For the Armada 370 and XP SoCs where the DT is used, we need to fill
at runtime the bridge_virt_base field on the
orion_addr_map_cfg. Therefore, remove the 'const' qualifier on this
field.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Until now, the PLAT_ORION configuration option was common to all the
Marvell EBU SoCs, and selecting this option had the effect of enabling
the MPP code, GPIO code, address decoding and PCIe code from
plat-orion, as well as providing access to driver-specific header
files from plat-orion/include.
However, the Armada 370 and XP SoCs will not use the MPP and GPIO code
(instead some proper pinctrl and gpio drivers are in preparation), and
generally, we want to move away from plat-orion and instead have
everything in mach-mvebu.
That said, in the mean time, we want to leverage the driver-specific
headers as well as the address decoding code, so we introduce
PLAT_ORION_LEGACY. The older Marvell SoCs need to select
PLAT_ORION_LEGACY, while the newer Marvell SoCs need to select
PLAT_ORION. Of course, when PLAT_ORION_LEGACY is selected, it
automatically selects PLAT_ORION.
Then, with just PLAT_ORION, you have the address decoding code plus
the driver-specific headers. If you add PLAT_ORION_LEGACY to this, you
gain the old MPP, GPIO and PCIe code.
Again, this is only a temporary solution until we make all Marvell EBU
platforms converge into the mach-mvebu directory. This solution avoids
duplicating the existing address decoding code into mach-mvebu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The functions for address mapping management now take void __iomem
pointers, so we remove the temporary "unsigned long" casts from the
mach-*/common.c files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The functions for time management now take void __iomem pointers, so
we remove the temporary "unsigned long" casts from the mach-*/common.c
files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The registration function for MPP now takes void __iomem pointers, so
we remove the temporary "unsigned long" casts from the mach-*/mpp.c
files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The registration functions for UARTs now take void __iomem pointers,
so we remove the temporary "unsigned long" casts from the
mach-*/common.c files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
|
|
Move custom orion platforms gpio code to orion-gpio to remove the
dependency on mach/gpio.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
|
|
The mv643xx ethernet controller limits the packet size for the TX
checksum offloading. This patch sets this limits for Kirkwood and
Dove which have smaller limits that the default.
As a side note, this patch is an updated version of a patch sent some years
ago: http://lists.infradead.org/pipermail/linux-arm-kernel/2010-June/017320.html
which seems to have been lost.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: <stable@vger.kernel.org>
|
|
The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Conflicts:
arch/arm/mach-kirkwood/common.c
|
|
Both IRQ and GPIO controllers can now be represented in DT. The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
|
|
The orion watchdog is expecting to be passed the physcial address of
the hardware, and will ioremap() it to give a virtual address it will
use as the base address for the hardware. However, when creating the
platform resource record, a virtual address was being used.
Add the necassary #define's so we can pass the physical address as
expected.
Tested on Kirkwood and Orion5x.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
|
|
dns323 and (at least) iconnect platforms are using hw led blinking, so,
instead of having 2 identicals .gpio_blink_set gpio-led hooks, move
dns323 code into gpio.c
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
gpio registers are for 32 gpios. Given that orion_gpio_set_blink is called
directly and not through gpiolib, it needs to make sure that the pin value
given to the internal functions are between 0 and 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add a varient of the basic clk-gate code. This variant calls a
function before gating the clock off. This function is used to disable
the SATA or PCIe PHY.
Now that all the drivers prepare and enable there clk as needed, there
is no need for the common code to keep track of which clocks need
gating on. Let the common clock framework turn off clocks which are
not used.
Buy using the added clk varient, when the clk framework turns off SATA
or PCIe clocks, we also disabled SATA and PCIe PHYs which were not
needed.
The function kirkwood_pcie_id() can now be called outside of __init
code, so remove this property for it, and functions it calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Let the machine pass to the platform which clock is used by the uart.
Enable the clock and use clk_get_rate() to determine its rate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Remove tclk from platform data. This makes the platform data
structure empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
It is not used anywhere in the sound driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a928081d391cd9a570afe3b2c692fdc broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
|
|
Conflicts:
arch/arm/kernel/setup.c
arch/arm/mach-shmobile/board-kota2.c
|
|
The former implementation adds a fix gpiochip label string
to the framework. This is confusing because orion_gpio_init
is called more than once and this ends up in different gpiochips
with the same label.
This patch adds the already present orion_gpio_chip_count to the
label string to make it unique in the system.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
