| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes and additions from Olof Johansson:
"The 64-bit set of updates this release cycle adds support for three
new platforms:
- Samsunc Exynos 7
- Freescale LS2085a
- Mediatek MT8173
For all these, the changes mostly consititude additions of DT
contents, but also some Kconfig entries to allow dependency/selection
of drivers per-platform, etc"
* tag '64bit-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: Kconfig: clean up two no-op Kconfig options from CONFIG_ARCH_TEGRA*
arm64: Fix sort of platform Kconfig entries
arm64: Add support for FSL's LS2085A SoC in Kconfig and defconfig
arm64: Add DTS support for FSL's LS2085A SoC
arm64: mediatek: Add MT8173 SoC Kconfig and defconfig
arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile
Document: DT: Add bindings for mediatek MT8173 SoC Platform
arm64: Add Tegra132 support
arm64: Enable ARMv8 based exynos7 SoC support
arm64: dts: Add nodes for mmc, i2c, rtc, watchdog, adc on exynos7
arm64: dts: Add PMU DT node for exynos7 SoC
arm64: dts: Add initial pinctrl support to exynos7
arm64: dts: Add initial device tree support for exynos7
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time with:
- Generic page-table framework for ARM IOMMUs using the LPAE
page-table format, ARM-SMMU and Renesas IPMMU make use of it
already.
- Break out the IO virtual address allocator from the Intel IOMMU so
that it can be used by other DMA-API implementations too. The
first user will be the ARM64 common DMA-API implementation for
IOMMUs
- Device tree support for Renesas IPMMU
- Various fixes and cleanups all over the place"
* tag 'iommu-updates-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (36 commits)
iommu/amd: Convert non-returned local variable to boolean when relevant
iommu: Update my email address
iommu/amd: Use wait_event in put_pasid_state_wait
iommu/amd: Fix amd_iommu_free_device()
iommu/arm-smmu: Avoid build warning
iommu/fsl: Various cleanups
iommu/fsl: Use %pa to print phys_addr_t
iommu/omap: Print phys_addr_t using %pa
iommu: Make more drivers depend on COMPILE_TEST
iommu/ipmmu-vmsa: Fix IOMMU lookup when multiple IOMMUs are registered
iommu: Disable on !MMU builds
iommu/fsl: Remove unused fsl_of_pamu_ids[]
iommu/fsl: Fix section mismatch
iommu/ipmmu-vmsa: Use the ARM LPAE page table allocator
iommu: Fix trace_map() to report original iova and original size
iommu/arm-smmu: add support for iova_to_phys through ATS1PR
iopoll: Introduce memory-mapped IO polling macros
iommu/arm-smmu: don't touch the secure STLBIALL register
iommu/arm-smmu: make use of generic LPAE allocator
iommu: io-pgtable-arm: add non-secure quirk
...
|
|
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
|
|
Paul Bolle pointed out that commit
d035fdfa27ac124bc8f94c3d7dc82ad069802170 ("arm64: Add Tegra132
support") included two Kconfig symbols that are now no-ops:
USB_ARCH_HAS_EHCI and HAVE_SMP. So, drop the two symbols.
This second version corrects a thinko in Paul Bolle's E-mail address.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/arm64
Merge "ARM: mediatek: arm64 changes for v3.20" from Matthias Brugger:
Add support for mt8173 SoC from Mediatek.
- add DT bindings documentation
- add dts files for SoC and evaluation board
- add to Kconfig and defconfig
* tag 'v3.20-next-arm64' of https://github.com/mbgg/linux-mediatek:
arm64: mediatek: Add MT8173 SoC Kconfig and defconfig
arm64: dts: Add mediatek MT8173 SoC and evaluation board dts and Makefile
Document: DT: Add bindings for mediatek MT8173 SoC Platform
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds support for FSL's LS2085A SoC in the arm64 Kconfig
and defconfig files.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnab Basu <arnab_basu@rocketmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ARM64_CPU_SUSPEND config option was introduced to make code providing
context save/restore selectable only on platforms requiring power
management capabilities.
Currently ARM64_CPU_SUSPEND depends on the PM_SLEEP config option which
in turn is set by the SUSPEND config option.
The introduction of CPU_IDLE for arm64 requires that code configured
by ARM64_CPU_SUSPEND (context save/restore) should be compiled in
in order to enable the CPU idle driver to rely on CPU operations
carrying out context save/restore.
The ARM64_CPUIDLE config option (ARM64 generic idle driver) is therefore
forced to select ARM64_CPU_SUSPEND, even if there may be (ie PM_SLEEP)
failed dependencies, which is not a clean way of handling the kernel
configuration option.
For these reasons, this patch removes the ARM64_CPU_SUSPEND config option
and makes the context save/restore dependent on CPU_PM, which is selected
whenever either SUSPEND or CPU_IDLE are configured, cleaning up dependencies
in the process.
This way, code previously configured through ARM64_CPU_SUSPEND is
compiled in whenever a power management subsystem requires it to be
present in the kernel (SUSPEND || CPU_IDLE), which is the behaviour
expected on ARM64 kernels.
The cpu_suspend and cpu_init_idle CPU operations are added only if
CPU_IDLE is selected, since they are CPU_IDLE specific methods and
should be grouped and defined accordingly.
PSCI CPU operations are updated to reflect the introduced changes.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add MT8173 arm64 Kconfig and defconfig files
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Arnd Bergmann <arnd at arndb.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/arm64
Merge "arm64: Add initial Tegra support" from Thierry Reding:
This adds support for the Tegra132 SoC, which is essentially a Tegra124
with a dual Denver CPU complex instead of the quad-Cortex-A15. There is
not much here, only the Kconfig entries, but it will allow us to more
easily get subsequent patches in (many of which have already been sent
for review).
* tag 'tegra-for-3.20-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: Add Tegra132 support
soc: tegra: Add thermal reset (thermtrip) support to PMC
ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
of: Add descriptions of thermtrip properties to Tegra PMC bindings
soc/tegra: pmc: Add Tegra132 support
soc/tegra: fuse: Add Tegra132 support
soc/tegra: fuse: Constify tegra_fuse_info structures
soc/tegra: Add Tegra132 support
clocksource: Build Tegra timer on 32-bit ARM only
soc/tegra: pmc: restrict compilation of suspend-related support to ARM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Emulate deprecated 'setend' instruction for AArch32 bit tasks.
setend [le/be] - Sets the endianness of EL0
On systems with CPUs which support mixed endian at EL0, the hardware
support for the instruction can be enabled by setting the SCTLR_EL1.SED
bit. Like the other emulated instructions it is controlled by an entry in
/proc/sys/abi/. For more information see :
Documentation/arm64/legacy_instructions.txt
The instruction is emulated by setting/clearing the SPSR_EL1.E bit, which
will be reflected in the PSTATE.E in AArch32 context.
This patch also restores the native endianness for the execution of signal
handlers, since the process could have changed the endianness.
Note: All CPUs on the system must have mixed endian support at EL0. Once the
handler is registered, hotplugging a CPU which doesn't support mixed endian,
could lead to unexpected results/behavior in applications.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add basic Kbuild support for the Tegra SoC family, and specifically,
the Tegra132 SoC. Tegra132 pairs the NVIDIA Denver CPU complex with
the SoC integration of Tegra124 - hence the use of ARCH_TEGRA and the
Tegra124 pinctrl option.
This patch was based on a patch originally written by Allen Martin
<amartin@nvidia.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ARM SMMU can walk LPAE page tables, so make use of the generic
allocator.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch add bitrev.h file to support rbit instruction,
so that we can do bitrev operation by hardware.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the necessary Kconfig entries to enable
support for the ARMv8 based exynos7 SoC. It also enables
RTC, WDT and Pinctrl for exynos7 SoC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq domain ARM updates from Thomas Gleixner:
"This set of changes make use of hierarchical irqdomains to provide:
- MSI/ITS support for GICv3
- MSI support for GICv2m
- Interrupt polarity extender for GICv1
Marc has come more cleanups for the existing extension hooks of GIC in
the pipeline, but they are going to be 3.20 material"
* 'irq-irqdomain-arm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
irqchip: gicv3-its: Fix ITT allocation
irqchip: gicv3-its: Move some alloc/free code to activate/deactivate
irqchip: gicv3-its: Fix domain free in multi-MSI case
irqchip: gic: Remove warning by including linux/irqdomain.h
irqchip: gic-v2m: Add DT bindings for GICv2m
irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
irqchip: mtk-sysirq: dt-bindings: Add bindings for mediatek sysirq
irqchip: mtk-sysirq: Add sysirq interrupt polarity support
irqchip: gic: Support hierarchy irq domain.
irqchip: GICv3: Binding updates for ITS
irqchip: GICv3: ITS: enable compilation of the ITS driver
irqchip: GICv3: ITS: plug ITS init into main GICv3 code
irqchip: GICv3: ITS: DT probing and initialization
irqchip: GICv3: ITS: MSI support
irqchip: GICv3: ITS: device allocation and configuration
irqchip: GICv3: ITS: tables allocators
irqchip: GICv3: ITS: LPI allocator
irqchip: GICv3: ITS: irqchip implementation
irqchip: GICv3: ITS command queue
irqchip: GICv3: rework redistributor structure
...
|
|
Following the suggestions from Andrew Morton and Stephen Rothwell,
Dont expand the ARCH list in kernel/gcov/Kconfig. Instead,
define a ARCH_HAS_GCOV_PROFILE_ALL bool which architectures
can enable.
set ARCH_HAS_GCOV_PROFILE_ALL on Architectures where it was
previously allowed + ARM64 which I tested.
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM64 SoC changes from Arnd Bergmann:
"This adds support for two new ARM64 platforms:
- ARM Juno
- AMD Seattle
We had submissions for a number of additional platforms from Samsung,
Freescale and Spreadtrum but are still working out the best process
for getting these merged"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: amd-seattle: Fix PCI bus range due to SMMU limitation
arm64: ARM: Fix the Generic Timers interrupt active level description
arm64: amd-seattle: Adding device tree for AMD Seattle platform
arm64: Add Juno board device tree.
arm64: Create link to include/dt-bindings to enable C preprocessor use.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
|
|
Initial revision of device tree for AMD Seattle Development platform.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Thomas Lendacky <Thomas.Lendacky@amd.com>
Signed-off-by: Joel Schopp <Joel.Schopp@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
secure_computing() is called first in syscall_trace_enter() so that
a system call will be aborted quickly without doing succeeding syscall
tracing if seccomp rules want to deny that system call.
On compat task, syscall numbers for system calls allowed in seccomp mode 1
are different from those on normal tasks, and so _NR_seccomp_xxx_32's need
to be redefined.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
ARM GICv2m specification extends GICv2 to support MSI(-X) with
a new register frame. This allows a GICv2 based system to support
MSI with minimal changes.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
[maz: converted the driver to use stacked irq domains,
updated changelog]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416941243-7181-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Get the show on the road...
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1416839720-18400-13-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Rather than duplicate the ARM_AMBA Kconfig symbol in both 32-bit and
64-bit ARM architectures, move the common definition to drivers/amba
where dependent drivers will be located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Not all of the errata we have workarounds for apply necessarily to all
SoCs, so people compiling a kernel for one very specific SoC may not
need to patch the kernel.
Introduce a new submenu in the "Platform selection" menu to allow
people to turn off certain bugs if they are not affected. By default
all of them are enabled.
Normal users or distribution kernels shouldn't bother to deselect any
bugs here, since the alternatives framework will take care of
patching them in only if needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[will: moved kconfig menu under `Kernel Features']
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Having the instruction emulation submenu underneath "platform selection"
is a great way to hide options we don't want people to use, but somewhat
confusing when you stumble across it there.
Move the menuconfig option underneath "kernel features", where it makes
a bit more sense.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The CP15 barrier instructions (CP15ISB, CP15DSB and CP15DMB) are
deprecated in the ARMv7 architecture, superseded by ISB, DSB and DMB
instructions respectively. Some implementations may provide the
ability to disable the CP15 barriers by disabling the CP15BEN bit in
SCTLR_EL1. If not enabled, the encodings for these instructions become
undefined.
To support legacy software using these instructions, this patch
register hooks to -
* emulate CP15 barriers and warn the user about their use
* toggle CP15BEN in SCTLR_EL1
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The SWP instruction was deprecated in the ARMv6 architecture. The
ARMv7 multiprocessing extensions mandate that SWP/SWPB instructions
are treated as undefined from reset, with the ability to enable them
through the System Control Register SW bit. With ARMv8, the option to
enable these instructions through System Control Register was dropped
as well.
To support legacy applications using these instructions, port the
emulation of the SWP and SWPB instructions from the arm port to arm64.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Typically, providing support for legacy instructions requires
emulating the behaviour of instructions whose encodings have become
undefined. If the instructions haven't been removed from the
architecture, there maybe an option in the implementation to turn
on/off the support for these instructions.
Create common infrastructure to support legacy instruction
emulation. In addition to emulation, also provide an option to support
hardware execution when supported. The default execution mode (one of
undef, emulate, hw exeuction) is dependent on the state of the
instruction (deprecated or obsolete) in the architecture and
can specified at the time of registering the instruction handlers. The
runtime state of the emulation can be controlled by writing to
individual nodes in sysctl. The expected default behaviour is
documented as part of this patch.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Patch 09a5723983 ("arm64: Use include/asm-generic/io.h") correctly
removed the GENERIC_IOMAP selection from ARM64, which is not needed
on architectures that have memory-mapped PCI I/O space, however
we now lack a pci_iomap() function.
Fortunately, there is already a generic implementation for this
case, so we just need to select GENERIC_PCI_IOMAP to make it all
work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 09a5723983 ("arm64: Use include/asm-generic/io.h")
|
|
Include the generic I/O header file so that duplicate implementations
can be removed. This will also help to establish consistency across more
architectures regarding which accessors they support.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The arm64 architecture has the ability to exclusively load and store
a pair of registers from an address (ldxp/stxp). Also the SLUB can take
advantage of a cmpxchg_double implementation to avoid taking some
locks.
This patch provides an implementation of cmpxchg_double for 64-bit
pairs, and activates the logic required for the SLUB to use these
functions (HAVE_ALIGNED_STRUCT_PAGE and HAVE_CMPXCHG_DOUBLE).
Also definitions of this_cpu_cmpxchg_8 and this_cpu_cmpxchg_double_8
are wired up to cmpxchg_local and cmpxchg_double_local (rather than the
stock implementations that perform non-atomic operations with
interrupts disabled) as they are used by the SLUB.
On a Juno platform running on only the A57s I get quite a noticeable
performance improvement with 5 runs of hackbench on v3.17:
Baseline | With Patch
-----------------+-----------
Mean 119.2312 | 106.1782
StdDev 0.4919 | 0.4494
(times taken to complete `./hackbench 100 process 1000', in seconds)
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
SMBIOS is important for server hardware vendors. It implements a spec for
providing descriptive information about the platform. Things like serial
numbers, physical layout of the ports, build configuration data, and the like.
Signed-off-by: Yi Li <yi.li@linaro.org>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
When user asks to turn off ASLR by writing "0" to
/proc/sys/kernel/randomize_va_space there should not be
any randomization to mmap base, stack, VDSO, libs, text and heap
Currently arm64 violates this behavior by randomising text.
Fix this by defining a constant ELF_ET_DYN_BASE. The randomisation of
mm->mmap_base is done by setup_new_exec -> arch_pick_mmap_layout ->
mmap_base -> mmap_rnd.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now when KVM has been reworked to support 48-bits host VA space, we can
allow systems to be configured with this option. However, the ARM SMMU
driver also needs to be tweaked for 48-bit support so only allow the
config option to be set when not including support for theSMMU.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
|
|
Merge patch-bomb from Andrew Morton:
- part of OCFS2 (review is laggy again)
- procfs
- slab
- all of MM
- zram, zbud
- various other random things: arch, filesystems.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
nosave: consolidate __nosave_{begin,end} in <asm/sections.h>
include/linux/screen_info.h: remove unused ORIG_* macros
kernel/sys.c: compat sysinfo syscall: fix undefined behavior
kernel/sys.c: whitespace fixes
acct: eliminate compile warning
kernel/async.c: switch to pr_foo()
include/linux/blkdev.h: use NULL instead of zero
include/linux/kernel.h: deduplicate code implementing clamp* macros
include/linux/kernel.h: rewrite min3, max3 and clamp using min and max
alpha: use Kbuild logic to include <asm-generic/sections.h>
frv: remove deprecated IRQF_DISABLED
frv: remove unused cpuinfo_frv and friends to fix future build error
zbud: avoid accessing last unused freelist
zsmalloc: simplify init_zspage free obj linking
mm/zsmalloc.c: correct comment for fullness group computation
zram: use notify_free to account all free notifications
zram: report maximum used memory
zram: zram memory size limitation
zsmalloc: change return value unit of zs_get_total_size_bytes
zsmalloc: move pages_allocated to zs_pool
...
|
|
Activate the RCU fast_gup for ARM64. We also need to force THP splits to
broadcast an IPI s.t. we block in the fast_gup page walker. As THP
splits are comparatively rare, this should not lead to a noticeable
performance degradation.
Some pre-requisite functions pud_write and pud_page are also added.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to implement fast_get_user_pages we need to ensure that the page
table walker is protected from page table pages being freed from under it.
This patch enables HAVE_RCU_TABLE_FREE, any page table pages belonging to
address spaces with multiple users will be call_rcu_sched freed. Meaning
that disabling interrupts will block the free and protect the fast gup
page walker.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Neither CMA nor noncoherent allocations support atomic allocations.
Add a dedicated atomic pool to support this.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Riley <davidriley@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ritesh Harjain <ritesh.harjani@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The interesting things here are:
- Turn on Config Request Retry Status Software Visibility. This
caused hangs last time, but we included a fix this time.
- Rework PCI device configuration to use _HPP/_HPX more aggressively
- Allow PCI devices to be put into D3cold during system suspend
- Add arm64 PCI support
- Add APM X-Gene host bridge driver
- Add TI Keystone host bridge driver
- Add Xilinx AXI host bridge driver
More detailed summary:
Enumeration
- Check Vendor ID only for Config Request Retry Status (Rajat Jain)
- Enable Config Request Retry Status when supported (Rajat Jain)
- Add generic domain handling (Catalin Marinas)
- Generate uppercase hex for modalias interface class (Ricardo Ribalda Delgado)
Resource management
- Add missing MEM_64 mask in pci_assign_unassigned_bridge_resources() (Yinghai Lu)
- Increase IBM ipr SAS Crocodile BARs to at least system page size (Douglas Lehr)
PCI device hotplug
- Prevent NULL dereference during pciehp probe (Andreas Noever)
- Move _HPP & _HPX handling into core (Bjorn Helgaas)
- Apply _HPP to PCIe devices as well as PCI (Bjorn Helgaas)
- Apply _HPP/_HPX to display devices (Bjorn Helgaas)
- Preserve SERR & PARITY settings when applying _HPP/_HPX (Bjorn Helgaas)
- Preserve MPS and MRRS settings when applying _HPP/_HPX (Bjorn Helgaas)
- Apply _HPP/_HPX to all devices, not just hot-added ones (Bjorn Helgaas)
- Fix wait time in pciehp timeout message (Yinghai Lu)
- Add more pciehp Slot Control debug output (Yinghai Lu)
- Stop disabling pciehp notifications during init (Yinghai Lu)
MSI
- Remove arch_msi_check_device() (Alexander Gordeev)
- Rename pci_msi_check_device() to pci_msi_supported() (Alexander Gordeev)
- Move D0 check into pci_msi_check_device() (Alexander Gordeev)
- Remove unused kobject from struct msi_desc (Yijing Wang)
- Remove "pos" from the struct msi_desc msi_attrib (Yijing Wang)
- Add "msi_bus" sysfs MSI/MSI-X control for endpoints (Yijing Wang)
- Use __get_cached_msi_msg() instead of get_cached_msi_msg() (Yijing Wang)
- Use __read_msi_msg() instead of read_msi_msg() (Yijing Wang)
- Use __write_msi_msg() instead of write_msi_msg() (Yijing Wang)
Power management
- Drop unused runtime PM support code for PCIe ports (Rafael J. Wysocki)
- Allow PCI devices to be put into D3cold during system suspend (Rafael J. Wysocki)
AER
- Add additional AER error strings (Gong Chen)
- Make <linux/aer.h> standalone includable (Thierry Reding)
Virtualization
- Add ACS quirk for Solarflare SFC9120 & SFC9140 (Alex Williamson)
- Add ACS quirk for Intel 10G NICs (Alex Williamson)
- Add ACS quirk for AMD A88X southbridge (Marti Raudsepp)
- Remove unused pci_find_upstream_pcie_bridge(), pci_get_dma_source() (Alex Williamson)
- Add device flag helpers (Ethan Zhao)
- Assume all Mellanox devices have broken INTx masking (Gavin Shan)
Generic host bridge driver
- Fix ioport_map() for !CONFIG_GENERIC_IOMAP (Liviu Dudau)
- Add pci_register_io_range() and pci_pio_to_address() (Liviu Dudau)
- Define PCI_IOBASE as the base of virtual PCI IO space (Liviu Dudau)
- Fix the conversion of IO ranges into IO resources (Liviu Dudau)
- Add pci_get_new_domain_nr() and of_get_pci_domain_nr() (Liviu Dudau)
- Add support for parsing PCI host bridge resources from DT (Liviu Dudau)
- Add pci_remap_iospace() to map bus I/O resources (Liviu Dudau)
- Add arm64 architectural support for PCI (Liviu Dudau)
APM X-Gene
- Add APM X-Gene PCIe driver (Tanmay Inamdar)
- Add arm64 DT APM X-Gene PCIe device tree nodes (Tanmay Inamdar)
Freescale i.MX6
- Probe in module_init(), not fs_initcall() (Lucas Stach)
- Delay enabling reference clock for SS until it stabilizes (Tim Harvey)
Marvell MVEBU
- Fix uninitialized variable in mvebu_get_tgt_attr() (Thomas Petazzoni)
NVIDIA Tegra
- Make sure the PCIe PLL is really reset (Eric Yuen)
- Add error path tegra_msi_teardown_irq() cleanup (Jisheng Zhang)
- Fix extended configuration space mapping (Peter Daifuku)
- Implement resource hierarchy (Thierry Reding)
- Clear CLKREQ# enable on port disable (Thierry Reding)
- Add Tegra124 support (Thierry Reding)
ST Microelectronics SPEAr13xx
- Pass config resource through reg property (Pratyush Anand)
Synopsys DesignWare
- Use NULL instead of false (Fabio Estevam)
- Parse bus-range property from devicetree (Lucas Stach)
- Use pci_create_root_bus() instead of pci_scan_root_bus() (Lucas Stach)
- Remove pci_assign_unassigned_resources() (Lucas Stach)
- Check private_data validity in single place (Lucas Stach)
- Setup and clear exactly one MSI at a time (Lucas Stach)
- Remove open-coded bitmap operations (Lucas Stach)
- Fix configuration base address when using 'reg' (Minghuan Lian)
- Fix IO resource end address calculation (Minghuan Lian)
- Rename get_msi_data() to get_msi_addr() (Minghuan Lian)
- Add get_msi_data() to pcie_host_ops (Minghuan Lian)
- Add support for v3.65 hardware (Murali Karicheri)
- Fold struct pcie_port_info into struct pcie_port (Pratyush Anand)
TI Keystone
- Add TI Keystone PCIe driver (Murali Karicheri)
- Limit MRSS for all downstream devices (Murali Karicheri)
- Assume controller is already in RC mode (Murali Karicheri)
- Set device ID based on SoC to support multiple ports (Murali Karicheri)
Xilinx AXI
- Add Xilinx AXI PCIe driver (Srikanth Thokala)
- Fix xilinx_pcie_assign_msi() return value test (Dan Carpenter)
Miscellaneous
- Clean up whitespace (Quentin Lambert)
- Remove assignments from "if" conditions (Quentin Lambert)
- Move PCI_VENDOR_ID_VMWARE to pci_ids.h (Francesco Ruggeri)
- x86: Mark DMI tables as initialization data (Mathias Krause)
- x86: Move __init annotation to the correct place (Mathias Krause)
- x86: Mark constants of pci_mmcfg_nvidia_mcp55() as __initconst (Mathias Krause)
- x86: Constify pci_mmcfg_probes[] array (Mathias Krause)
- x86: Mark PCI BIOS initialization code as such (Mathias Krause)
- Parenthesize PCI_DEVID and PCI_VPD_LRDT_ID parameters (Megan Kamiya)
- Remove unnecessary variable in pci_add_dynid() (Tobias Klauser)"
* tag 'pci-v3.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (109 commits)
arm64: dts: Add APM X-Gene PCIe device tree nodes
PCI: Add ACS quirk for AMD A88X southbridge devices
PCI: xgene: Add APM X-Gene PCIe driver
PCI: designware: Remove open-coded bitmap operations
PCI/MSI: Remove unnecessary temporary variable
PCI/MSI: Use __write_msi_msg() instead of write_msi_msg()
MSI/powerpc: Use __read_msi_msg() instead of read_msi_msg()
PCI/MSI: Use __get_cached_msi_msg() instead of get_cached_msi_msg()
PCI/MSI: Add "msi_bus" sysfs MSI/MSI-X control for endpoints
PCI/MSI: Remove "pos" from the struct msi_desc msi_attrib
PCI/MSI: Remove unused kobject from struct msi_desc
PCI/MSI: Rename pci_msi_check_device() to pci_msi_supported()
PCI/MSI: Move D0 check into pci_msi_check_device()
PCI/MSI: Remove arch_msi_check_device()
irqchip: armada-370-xp: Remove arch_msi_check_device()
PCI/MSI/PPC: Remove arch_msi_check_device()
arm64: Add architectural support for PCI
PCI: Add pci_remap_iospace() to map bus I/O resources
of/pci: Add support for parsing PCI host bridge resources from DT
of/pci: Add pci_get_new_domain_nr() and of_get_pci_domain_nr()
...
Conflicts:
arch/arm64/boot/dts/apm-storm.dtsi
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- a cleanup series to get rid of mindlessly copied code.
- another bunch of new pointlessly different interrupt chip drivers.
Adding homebrewn irq chips (and timers) to SoCs must provide a
value add which is beyond the imagination of mere mortals.
- the usual SoC irq controller updates, IOW my second cat herding
project"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
irqchip: gic-v3: Implement CPU PM notifier
irqchip: gic-v3: Refactor gic_enable_redist to support both enabling and disabling
irqchip: renesas-intc-irqpin: Add minimal runtime PM support
irqchip: renesas-intc-irqpin: Add helper variable dev = &pdev->dev
irqchip: atmel-aic5: Add sama5d4 support
irqchip: atmel-aic5: The sama5d3 has 48 IRQs
Documentation: bcm7120-l2: Add Broadcom BCM7120-style L2 binding
irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller
irqchip: renesas-irqc: Add binding docs for new R-Car Gen2 SoCs
irqchip: renesas-irqc: Add DT binding documentation
irqchip: renesas-intc-irqpin: Document SoC-specific bindings
openrisc: Get rid of handle_IRQ
arm64: Get rid of handle_IRQ
ARM: omap2: irq: Convert to handle_domain_irq
ARM: imx: tzic: Convert to handle_domain_irq
ARM: imx: avic: Convert to handle_domain_irq
irqchip: or1k-pic: Convert to handle_domain_irq
irqchip: atmel-aic5: Convert to handle_domain_irq
irqchip: atmel-aic: Convert to handle_domain_irq
irqchip: gic-v3: Convert to handle_domain_irq
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM64 SoC changes from Arnd Bergmann:
"Starting with 3.18, we are merging SoC-specific changes for arm64
through the arm-soc tree, like we have been doing for arm32.
This time, there is only one set of changes, adding support for the
Cavium "Thunder" Soc family. Since the changes are relatively small,
this includes Kconfig, defconfig and DT changes.
If all goes well, we will never require adding actual C source code
for platform support in arm64, given that the architecture is more
clearly defined and we have moved out a lot of the platform specifics
into device drivers for arm32 already"
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64, defconfig: Enable Cavium Thunder SoC in defconfig
arm64, thunder: Add Kconfig option for Cavium Thunder SoC Family
arm64, thunder: Document devicetree bindings for Cavium Thunder SoC
arm64, thunder: Add initial dts for Cavium Thunder SoC
|
|
The Xen ARM API is stable since Xen 4.4 and everything has been
upstreamed in Linux for ARM and ARM64. Therefore we can drop "EXPERIMENTAL"
from the Xen option in the both Kconfig.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
|
|
This introduces ARCH_THUNDER to enable soc specific drivers and dtb
files.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the generic PCI domain and OF functions to provide support for PCI
on arm64.
[bhelgaas: Change comments to use generic PCI, not just PCIe. Nothing at
this level is PCIe-specific.]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This reverts commit 668ebd106860f09f43993517f786a2ddfd0f9ebe.
... because of lots of warnings during boot if Linux isn't started as an EFI
application:
WARNING: CPU: 4 PID: 1 at
/work/Linux/linux-2.6-aarch64/drivers/firmware/dmi_scan.c:591 dmi_matches+0x10c/0x110()
dmi check: not initialized yet.
Modules linked in:
CPU: 4 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc4+ #606
Call trace:
[<ffffffc000087fb0>] dump_backtrace+0x0/0x124
[<ffffffc0000880e4>] show_stack+0x10/0x1c
[<ffffffc0004d58f8>] dump_stack+0x74/0xb8
[<ffffffc0000ab640>] warn_slowpath_common+0x8c/0xb4
[<ffffffc0000ab6b4>] warn_slowpath_fmt+0x4c/0x58
[<ffffffc0003f2d7c>] dmi_matches+0x108/0x110
[<ffffffc0003f2da8>] dmi_check_system+0x24/0x68
[<ffffffc0006974c4>] atkbd_init+0x10/0x34
[<ffffffc0000814ac>] do_one_initcall+0x88/0x1a0
[<ffffffc00067aab4>] kernel_init_freeable+0x148/0x1e8
[<ffffffc0004d2c64>] kernel_init+0x10/0xd4
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
SMBIOS is important for server hardware vendors. It implements a spec for
providing descriptive information about the platform. Things like serial
numbers, physical layout of the ports, build configuration data, and the like.
This has been tested by dmidecode and lshw tools.
This patch adds the call to dmi_scan_machine() to arm64_enter_virtual_mode(),
as that is the point where the EFI Configuration Tables are registered as
being available. It needs to be in an early_initcall anyway as dmi_id_init(),
which is an arch_initcall itself, depends on dmi_scan_machine() having been
called already.
Signed-off-by: Yi Li <yi.li@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Raising the current maximum limit to 64. This is needed for Cavium's
Thunder systems that will have at least 48 cores per die.
The change keeps the current memory footprint in cpu mask structures.
It does not break existing code. Setting the maximum to 64 cpus still
boots systems with less cpus.
Mark's Juno happily booted with a NR_CPUS=64 kernel.
Tested on our Thunder system with 48 cores. We could see interrupts to
all cores.
Cc: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
