| Age | Commit message (Collapse) | Author |
|---|
|
|
|
rmobile-fixes-for-linus
|
|
Keep the ZB clock enabled on sh73a0 to allow the BSC
to access external peripherals hooked up to CS signals.
This is needed to unbreak Ethernet support on sh73a0 boards
such as AG5EVM and Kota2 together with the following patch:
794d78f drivers: sh: late disabling of clocks V2
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix IRQ support on the AG5EVM board. The sh73a0 and the AG5EVM
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke AG5EVM irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch updates the Kota2 board support code to
use the recently merged TPU LED driver whenever
possible.
The sh73a0 SoC has 5 TPU hardware blocks each with
4 timer channels which in theory allows a total of
20 LEDs to be controlled by "leds-renesas-tpu"
driver instances. The Kota2 board has 4 LEDs connected
to GPIO pins that also come with TPU pin functions, so
this patch ties up these 4 LEDS and leaves the remaining
3 LEDS for the GPIO based LED driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix IRQ support on the Kota2 board. The sh73a0 and the Kota2
board make use of the ARM GIC hardware block as main interrupt
controller. The following commit changed the default behaviour
for non-device tree platforms and broke Kota2 irq support:
f37a53c ARM: gic: fix irq_alloc_descs handling for sparse irq
Without this fix the following warning triggers at boot:
NR_IRQS:1024 nr_irqs:1024 1024
------------[ cut here ]------------
WARNING: at arch/arm/common/gic.c:607 gic_init+0x90/0x2e4()
Cannot allocate irq_descs @ IRQ16, assuming pre-allocated
[<c000c868>] (unwind_backtrace+0x0/0xe0) from [<c001857c>] (warn_slowpath_commo)
[<c001857c>] (warn_slowpath_common+0x48/0x60) from [<c00185d8>] (warn_slowpath_)
[<c00185d8>] (warn_slowpath_fmt+0x2c/0x3c) from [<c029ee08>] (gic_init+0x90/0x2)
[<c029ee08>] (gic_init+0x90/0x2e4) from [<c029f278>] (sh73a0_init_irq+0x30/0x18)
[<c029f278>] (sh73a0_init_irq+0x30/0x184) from [<c029c0b4>] (init_IRQ+0x14/0x1c)
[<c029c0b4>] (init_IRQ+0x14/0x1c) from [<c029a5cc>] (start_kernel+0x15c/0x2b8)
[<c029a5cc>] (start_kernel+0x15c/0x2b8) from [<4000803c>] (0x4000803c)
---[ end trace 1b75b31a2719ed1c ]---
With this fix applied interrupts work as expected.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Support PINT on sh73a0 and Kota2 using INTC PINT macros.
With this patch applied the Kota2 ethernet is handled
through one of the chained sh73a0 PINT interrupt controllers.
sh73a0 PINT support is included in 3.2-rc but the Kota2 board
code does not make use of this shared code base without this
patch. Without this patch kota2 on-board ethernet is broken.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'rmobile-fixes-for-linus' of git://github.com/pmundt/linux-sh:
ARM: mach-shmobile: cpuidle single/global and last_state fixes
ARM: mach-shmobile: move helper macro PORTCR to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_xx to sh_pfc.h
ARM: mach-shmobile: move helper macro PORT_DATA_xx to sh_pfc.h
ARM: mach-shmobile: ap4evb: remove white space from end of line
ARM: mach-shmobile: clock-sh7372: remove un-necessary index
ARM: mach-shmobile: kota2: add comment out separator
ARM: mach-shmobile: sh73a0: add MMC data pin pull-up
|
|
* 'sh-fixes-for-linus' of git://github.com/pmundt/linux-sh:
mailmap: Fix up some renesas attributions
sh: clkfwk: Kill off remaining debugfs cruft.
drivers: sh: Kill off dead pathname for runtime PM stub.
drivers: sh: Generalize runtime PM platform stub.
sh: Wire up process_vm syscalls.
sh: clkfwk: add clk_rate_mult_range_round()
serial: sh-sci: Fix up SH-2A SCIF support.
sh: Fix cached/uncaced address calculation in 29bit mode
|
|
into fixes
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
|
|
The following error is seen in some case when mounting rootfs from
SD/MMC cards.
Waiting for root device /dev/mmcblk0p1...
mmc1: host does not support reading read-only switch. assuming write-enable.
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 SDC 3.74 GiB
mmcblk0: p1
mmc1: Timeout waiting for hardware interrupt.
mmcblk0: error -110 transferring data, sector 3678224, nr 40, cmd response 0x900, card status 0xc00
end_request: I/O error, dev mmcblk0, sector 3678225
Buffer I/O error on device mmcblk0p1, logical block 458754
lost page write due to I/O error on mmcblk0p1
This patch fixes the problem by lowering the usdhc clock and correcting
watermark configuration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The AUTO_ZRELADDR selection for ARCH_IMX_V4_V5 and ARCH_MX5 should
really be mutually exclusive to ZBOOT_ROM just like what ARCH_IMX_V6_V7
does.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The config symbol ARCH_MX3 has been removed by commit 'a89cf59
arm/imx: merge i.MX3 and i.MX6', and it should not be referenced
any more.
The patch also change ARCH_MX* to SOC_IMX* for other platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds I2C support to r8a7740 CPU
which has lasting errata on I2C I/O pad reset.
This patch is including work-around.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds PFC support for the R8A7740 (R-Mobile A1) CPU
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into fixes
|
|
Enable the headphone detection gpio on tegra platform.
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Ventana uses the same SDHCI GPIOs as Seaboard; PI6 (70) is the power GPIO
for the SD port, and there is no power GPIO for the MMC chip.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
*_pinmux_init() register the GPIO and pinmux devices so that they're ready
before any other device needs them.
*_pinmux_init() are also called by board-dt.c in order to set up the GPIO
and pinmux configurations. In this case, if we register the devices, they
end up being probed once due to this registration, and a second time due
to a device-tree node (or vice-versa). The second probe fails since the
memory regions are already requested. Besides, we don't actually want the
duplicated devices.
To avoid this duplicate registration, modify *_pinmux_init() to check
whether it's running on a DT machine. If not, register the pinmux devices.
If so, don't register them.
Finally, modify board-dt.c to call the *_pinmux_init() after all devices have
been instantiated from device-tree. This allows the GPIO and pinmux devices
to be instantiated and initialized before calling functions to configure the
hardware.
This has one disadvantage: The pinmux and GPIO initialization now happens
after /all/ devices are instantiated, rather than after just gpio and
pinmux but before anything else. So the correct HW configuration is not
in place when e.g. the SD/MMC device is probed. Long-term, this should be
solved by doing both:
a) Initializing the HW state from DT nodes during GPIO and pinmux device
probe.
b) Using the deferred driver probe mechanism, so that drivers can defer
their probe until after the gpio and pinmux drivers have probed.
v2: s/int is_dt/bool is_dt/
v3: Use of_machine_is_compatible inside *_pinmux_init() rather than passing
an explicit parameter into the function from outside.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
|
|
Since 193ab2a6070039e7ee2b9b9bebea754a7c52fd1b, various AT91 boards don't
register USBA adapters anymore due to depending on a now non-existing
symbol. Fix the symbol name.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: stable@kernel.org
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
VMALLOC_END is defined in terms of AT91_VIRT_BASE but this needs
mach/hardware.h for it's definition.
In file included from arch/arm/mach-at91/board-usb-a926x.c:26:0:
include/linux/mm.h: In function 'is_vmalloc_addr':
include/linux/mm.h:305:41: error: 'AT91_VIRT_BASE' undeclared (first use in this function)
include/linux/mm.h:305:41: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
|
|
In commit fb149f9e28354 we introduce ioremap support for static map_io, we do
not need this register entry anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
639da5ee3 (ARM: add an extra temp register to the low level debugging
addruart macro) didn't include picoxcell as it hadn't been merged at the
time. Fix up the compile breakage by adding the extra temp parameter.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
|
|
CONFIG_MSM_SCM uses the smc instruction, which with some
toolchains requires a ".arch_extension" directive.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
|
The merge commit "526b264 Merge branch 'imx/cleanup' into imx/devel"
left a duplicated mx28_add_mxs_mmc() call, which causes the problem
below during boot.
kobject_add_internal failed for mxs-mmc.1 with -EEXIST, don't try
to register things with the same name in the same directory.
The patch removes this leftover and also change mmc0 adding to align
with mmc1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (31 commits)
ARM: OMAP: Fix export.h or module.h includes
ARM: OMAP: omap_device: Include linux/export.h
ARM: OMAP2: Fix H4 matrix keyboard warning
ARM: OMAP1: Remove unused omap-alsa.h
ARM: OMAP1: Fix warnings about enabling 32 KiHz timer
ARM: OMAP2+: timer: Remove omap_device_pm_latency
ARM: OMAP2+: clock data: Remove redundant timer clkdev
ARM: OMAP: Devkit8000: Remove double omap_mux_init_gpio
ARM: OMAP: usb: musb: OMAP: Delete unused function
MAINTAINERS: Update linux-omap git repository
ARM: OMAP: change get_context_loss_count ret value to int
ARM: OMAP4: hsmmc: configure SDMMC1_DR0 properly
ARM: OMAP4: hsmmc: Fix Pbias configuration on regulator OFF
ARM: OMAP3: hwmod: fix variant registration and remove SmartReflex from common list
ARM: OMAP: I2C: Fix omap_register_i2c_bus() return value on success
ARM: OMAP: dmtimer: Include linux/module.h
ARM: OMAP2+: l3-noc: Include linux/module.h
ARM: OMAP2+: devices: Fixes for McPDM
ARM: OMAP: Fix errors and warnings when building for one board
ARM: OMAP3: PM: restrict erratum i443 handling to OMAP3430 only
...
|
|
|
|
Commit 32aaeffbd4a7457bf2f7448b33b5946ff2a960eb (Merge branch
'modsplit-Oct31_2011'...) caused some build errors. Fix these
and make sure we always have export.h or module.h included
for MODULE_ and EXPORT_SYMBOL users:
$ grep -rl ^MODULE_ arch/arm/*omap*/*.c | xargs \
grep -L linux/module.h
arch/arm/mach-omap2/dsp.c
arch/arm/mach-omap2/mailbox.c
arch/arm/mach-omap2/omap-iommu.c
arch/arm/mach-omap2/smartreflex.c
Also check we either have export.h or module.h included
for the files exporting symbols:
$ grep -rl EXPORT_SYMBOL arch/arm/*omap*/*.c | xargs \
grep -L linux/export.h | xargs grep -L linux/module.h
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These files didn't exist at the time of the module.h split, and
so were not fixed by the commits on that baseline. Since they use
the EXPORT_SYMBOL and/or THIS_MODULE macros, they will need the
new export.h file included that provides them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
cpuidle: Single/Global registration of idle states
cpuidle: Split cpuidle_state structure and move per-cpu statistics fields
cpuidle: Remove CPUIDLE_FLAG_IGNORE and dev->prepare()
cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
ACPI: Fix CONFIG_ACPI_DOCK=n compiler warning
ACPI: Export FADT pm_profile integer value to userspace
thermal: Prevent polling from happening during system suspend
ACPI: Drop ACPI_NO_HARDWARE_INIT
ACPI atomicio: Convert width in bits to bytes in __acpi_ioremap_fast()
PNPACPI: Simplify disabled resource registration
ACPI: Fix possible recursive locking in hwregs.c
ACPI: use kstrdup()
mrst pmu: update comment
tools/power turbostat: less verbose debugging
|
|
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
