| Age | Commit message (Collapse) | Author |
|---|
|
Add IRQ and register base address definitions for MIPI CSI slave devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Naming changed for consistency with s5pv310 where there are two instances
of the device.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds DM9000 Ethernet Controller device support for SMDKV210.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds the SROM controller clock to the list of clocks to be enabled at
boot time. It is required to be enabled at boot time since the modules connected
over the SROM interface such as the Ethernet controller need an operational SROM.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch modifies the following.
1. Moves the SROM controller mapping from S5PV210 specific code to
S5P common code. The SROM controller mapping can be used for all
S5P SoCs.
2. Define the SROM controller physical address for S5P64X0, S5P6442,
S5PC100, S5PV210 and S5PV310.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some of the S5P platforms like S5PC100 and S5PV210 include SROM banks
4 and 5 in addition to SROM banks 0 to 3. This patch adds register
offsets for SROM bank 4 and 5.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds shift macros for the SROM Bus width and control
register to represent the shift count for the 5th and 6th SROM
banks. Some of the S5P SOCs have them.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The SROM register difinitions of S5PV310/S5PC210 (mach/regs-srom.h)
can be used to other S5P SoCs such as S5PV210/S5PC110. So moved into
plat/regs-srom.h of plat-s5p directory.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: Fix re-probing with PM_POST_RESTORE notification
mmc: atmel-mci: fix multiblock SDIO transfers
mmc: at91_mci: fix multiblock SDIO transfers
|
|
arm: export dma_set_coherent_mask
While a regression was fixed with commit 710224fa2750cf (arm: fix
"arm: fix pci_set_consistent_dma_mask for dmabounce devices"), a
new one was introduced as dma_set_coherent_mask wasn't exported
for modules. This patch takes care for this issue.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: INTC interrupt priority level demux fix
ARM: mach-shmobile: fix compile warning in mm/init.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: update MAX8998 platform data to get rid of WARN()
ARM S3C24XX: Fix compilation of PM code for S3C2416
ARM: S3C24XX: Fix CONFIG_S3C_DEV_NAND Kconfig entry
|
|
As PControl G20 is a carrier board for the Stamp9G20 SoM, some code can
be shared. Therefore board-stamp9g20.c is refactored to allow reusing the
SoM initialization and board-pcontrol-g20.c is modified to use it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The uhpck clock should be divided from the utmi clock, not its parent
(main). This change is mostly cosmetic as the uhpck rate value is not
used anywhere except for the debugfs clock output.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fix interrupt priority level handling on SH-Mobile ARM.
SH-Mobile ARM platforms using multiple interrupt priority
levels need this patch to fix a potential dead lock that
may occur if multiple interrupts with different levels
are pending simultaneously.
The default INTC configuration is to use the same priority
level for all interrupts, so this issue does not trigger by
default. It is however common for board code to override the
interrupt priority for certain interrupt sources depending
on the application. Without this fix such boards may lock up.
In detail, this patch updates the INTC code in entry-macro.S
to make sure that the INTLVLA register gets set as expected.
To trigger this bug modify the board specific code to adjust
the interrupt priority level for the ethernet chip. After
changing the priority level simply use flood ping to drown
the board with interrupts.
This patch applies to INTCA-based processors such as sh7372,
sh7377 and sh7372. GIC-based processors are not affected.
Suitable for v2.6.37-rc and stable from v2.6.34 to v2.6.36.
Cc: stable@kernel.org
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Turn down the warning noise from the compiler,
basically a SH-Mobile specific version of the
patch located in the RMK patch tracker:
6484/1: "fix compile warning in mm/init.c",
Without this patch the following warning triggers:
CC arch/arm/kernel/sys_arm.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
CC arch/arm/kernel/traps.o
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds new entries required by the new version of MAX8998
driver. Without them, the driver fails to init. See commit 50f19a4596
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
S3C2416 PM code uses low-level sleep routines from S3C2412 code,
but these routines are compiled only for S3C2412 SoC.
Split S3C2412_PM to two parts: S3C2412_PM, S3C2412_PM_SLEEP and
select last in S3C2416's Kconfig.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Should be CONFIG_S3C_DEV_NAND instead of CONFIG_S3C_DEVICE_NAND.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP2: PRCM: fix some SHIFT macros that were actually bitmasks
OMAP2+: PM/serial: fix console semaphore acquire during suspend
OMAP1: SRAM: fix size for OMAP1611 SoCs
arm: omap2: io: fix clk_get() error check
arm: plat-omap: counter_32k: use IS_ERR() instead of NULL check
omap: nand: remove hardware ECC as default
omap: zoom: wl1271 slot is MMC_CAP_POWER_OFF_CARD
omap: PM debug: fix wake-on-timer debugfs dependency
|
|
Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.
Cc: stable@kernel.org
Signed-off-by: Valentine Barshak <vbarshak@mvista.com>
Signed-off-by: George G. Davis <gdavis@mvista.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.
At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.
All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.
This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.
Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this. These could be added later if it
matters.
Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The current implementation of the v7_coherent_*_range function assumes
that the D and I cache lines have the same size, which is incorrect
architecturally. This patch adds the icache_line_size macro which reads
the CTR register. The main loop in v7_coherent_*_range is split in two
independent loops or the D and I caches. This also has the performance
advantage that the DSB is moved outside the main loop.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The current implementation of the dcache_line_size macro reads the L1
cache size from the CCSIDR register. This, however, is not guaranteed to
be the smallest cache line in the cache hierarchy. The patch changes to
the macro to use the more architecturally correct CTR register.
Reported-by: Kevin Sapp <ksapp@quicinc.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 0d8e2d0dad98a693bad88aea6876ac8b94ad95c6 (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Kernel was failing to boot on omap1611 based OSK boards due to
mis-configured SRAM size. Existing code was using a hard-coded value
for 250k, which was then rounded down by PAGE_SIZE. Increasing this to
256k allows kernel to boot on omap1611 SoCs.
Problem reported by and initial fix suggested by Tim Bird.
Thanks to Tony Lindgren for helping diagnose the problem to being
specific to OMAP1611 and not affecting OMAP1610/OMAP1623.
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
clk_get() return value should be checked with IS_ERR().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* 'fixes/2637-rc5/s3c24xx' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: Fix mess with gpio {set,get}_pull callbacks
ARM: mini2440: Fix Kconfig to allow kernel to build
ARM: S3C2412: Fix typo in CONFIG_CPU_S3C2412_ONLY definition
ARM: S3C2443: Select properly ARM core type
ARM: SMDK2416: Select MACH_SMDK, S3C_DEV_NAND, S3C_DEV_USB_HOST
|
|
Currently the {set,get}_pull callbacks of the s3c24xx_gpiocfg_default structure
are initalized via s3c_gpio_{get,set}pull_1up. This results in a linker
error when only CONFIG_CPU_S3C2442 is selected:
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f4): undefined reference to
`s3c_gpio_getpull_1up'
arch/arm/plat-s3c24xx/built-in.o:(.data+0x13f8): undefined reference to
`s3c_gpio_setpull_1up'
The s3c2442 has pulldowns instead of pullups compared to the s3c2440.
The method of controlling them is the same though.
So this patch modifies the existing s3c_gpio_{get,set}pull_1up helper functions
to take an additional parameter deciding whether the pin has a pullup or pulldown.
The s3c_gpio_{get,set}pull_1{down,up} functions then wrap that functions passing
either S3C_GPIO_PULL_UP or S3C_GPIO_PULL_DOWN.
Furthermore this patch sets up the s3c24xx_gpiocfg_default.{get,set}_pull fields
in the s3c244{0,2}_map_io function to the new pulldown helper functions.
Based on patch from "Lars-Peter Clausen" <lars@metafoo.de>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Commit 0ea129300982 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
clk_get() returns ERR_PTR() on error, not NULL.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated to include err.h to compile on omap1]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch complements ed919b0 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.
This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6524/1: GIC irq desciptor bug fix
ARM: 6523/1: iop: ensure sched_clock() is notrace
ARM: 6456/1: Fix for building DEBUG with sa11xx_base.c as a module.
ARM: 6519/1: kuser: Fix incorrect cmpxchg syscall in kuser helpers
ARM: 6505/1: kprobes: Don't HAVE_KPROBES when CONFIG_THUMB2_KERNEL is selected
ARM: 6508/1: vexpress: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6507/1: RealView: Correct data alignment in headsmp.S for CONFIG_THUMB2_KERNEL
ARM: 6504/1: Thumb-2: Fix long-distance conditional branches in head.S for Thumb-2.
ARM: 6503/1: Thumb-2: Restore sensible zImage header layout for CONFIG_THUMB2_KERNEL
ARM: 6502/1: Thumb-2: Fix CONFIG_THUMB2_KERNEL breakage in compressed/head.S
ARM: 6501/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in mm/proc-v7.S
ARM: 6500/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in kernel/head.S
ARM: 6499/1: Thumb-2: Correct data alignment for CONFIG_THUMB2_KERNEL in bootp/init.S
ARM: 6498/1: vfp: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6497/1: kexec: Correct data alignment for CONFIG_THUMB2_KERNEL
ARM: 6496/1: GIC: Do not try to register more then NR_IRQS interrupts
ARM: cns3xxx: Fix build with CONFIG_PCI=y
|
|
|
|
gic_set_cpu will directly use irq_desc[]. If CONFIG_SPARSE_IRQ is
enabled, there is no irq_desc[]. So we need use irq_to_desc(irq) to
get the descriptor for irq.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Include sched.h to ensure sched_clock() has the notrace
annotation, and mark any functions it calls as notrace
too.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The existing code invokes the syscall with rubbish in r7,
due to what looks like an incorrect literal load idiom.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The MACH_MINI2440 entry requires the backlight LED driver, but this
subsystem has not been enabled and the select of LEDS_TRIGGER_BACKLIGHT
alone is insufficient to enable the necessary bits of the LED driver.
Add NEW_LEDS, LEDS_CLASS and LEDS_TRIGGER to the select to allow the
kernel to link.
This fixes the following error:
drivers/built-in.o: In function `led_trigger_set':
/home/ben/linux.git/drivers/leds/led-triggers.c:116: undefined reference to `led_brightness_set'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Wakeup-on-timer code does not have/need debugfs dependency. Move
the function out of debugfs ifdef.
Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
for the epson frambuffer support it's CONFIG_FB_S1D13XXX
not CONFIG_FB_S1D135XX
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
as based on http://www.picotux.com/pt200/picotux200.pdf
these board does not have such I/O
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
to be a few more concistant with the other boards
as ek is for evaluation kit and dk for development kit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
|
|
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Ajeco 1ARM Single Board Computer
- Sperry-Sun KAFA board
- picotux 200
Remove the deprecated at91_init_serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
|
