| Age | Commit message (Collapse) | Author |
|---|
|
WARNING: vmlinux.o(.text+0xbf38): Section mismatch in reference from the function pci_versatile_scan_bus() to the function .devinit.text:pci_scan_bus_parented()
The function pci_versatile_scan_bus() references
the function __devinit pci_scan_bus_parented().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
My attempt to make the LEDs only compile for RealView and
Versatile was futile: I missed the Versatile Express. So invert
the logic and explicitly include the platforms to compile for.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds a simple driver supporting the new LED framework with
triggers and all for the RealView and Versatile platforms. The
RealView and Versatile platform drivers were arranged to compile
for all-but-integrator as a side effect since the Integrator has
a different LED driver.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds some platform data for the character LCD found in the
RealView and Versatile reference designs from ARM.
Signed-off-by: Linus Walleij <triad@df.lth.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds platform data for the PL022 to the ARM Versatile reference
design, and adds the necessary clock definition.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds platform data for the PL022 to the ARM RealView reference
designs, adds the necessary clock definition and fixes a badly
defined IRQ line on the PB1176.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This is a number of basic fixes to the PB1176 that makes it tick
properly:
- Detect MMC insertion/removal even when PL061 GPIO is not compiled
in. The register to read this status directly is removed on the
PB1176.
- Define the UART3 on the DevChip (where is actually is) and define
the new UART4 serial port on the FPGA.
- Also define the clocks for these two UARTs apropriately.
- Remove the false notion that the PB1176 should have its CLCD
on the ISSP, this is not the case, it is in the DevChip.
- Remove the defintions and the previously commented-out PL081
DMAC. As confirmed by mail this was found to be broken on the
PB1176 board and removed from the subsequent FPGA images.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
daughterboard
This patch adds support for the Cortex-A9 local timers available when
using the CA9X4 daughterboard with the Versatile Express.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch fixes on wrong function name in include/plat/sdhci.h for Samsung.
The 's5pc100_default_sdhci0()' function should be chnaged to
's5pv210_default_sdhci0()'. Because 's5pv210_default_sdhci0()' must be pair.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The S5P6442 PLL setting announce message incorrectly displays S5P6440
as the SoC. Change it to S5P6442.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch fixes the following compilation problem if only NCP machine
is selected:
arch/arm/mach-s3c64xx/s3c6410.c: In function 's3c6410_map_io':
arch/arm/mach-s3c64xx/s3c6410.c:51: error: implicit declaration of function 's3c6410_default_sdhci2'
And also adds missed 's3c6400_default_sdhci2'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix and added comments]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
1. Corrected shift values of I2S and UART clocks (CLK_GATE_IP3), which were
defined incorrectly.
2. Corrected shift values of sclk_audio, uclk1, sclk_fimd, sclk_mmc,
sclk_spi, sclk_pwm, which had duplicated .enable/.ctrlbit with their
twins defined in struct clk init_clocks_disable[] and struct clk
init_clocks[]. We've changed their .enable/.ctrlbit to use CLK_SRC_MASK
register to avoid the duplicated clock problem described below.
NOTE: Duplicated Clock Problem
Please note that each clock definition should access different control
register; otherwise, the system may suffer lockups. For example, if we
have two clock definitions "a" and "b" which access the same register
(and the shift value). Then, when we do:
module A
clk = clk_get("a");
clk->clk_enable(clk);
module B (context switch)
clk = clk_get("b");
clk->clk_enable(clk);
do something with clk.
clk->clk_disable(clk);
module A (context switch)
do something with clk
* At this point, the system may hang.
Therefore, there should be no clock definitions with the same contol
register/shift. If we need to create "aliases", then, creating child
clocks sharing the clock should be fine.
3. Corrected other sclk_* shift values and access registers.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and message fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch fixes bug on eint type set function, s5p_irq_eint_set_type().
In the IRQ_TYPE_EDGE_FALLING case, S5P_EXTINT_FALLEDGE is right
instead of S5P_EXTINT_RISEEDGE
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Cc: <stable@kernel.org>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
RealView boards with certain revisions of the L210/L220 cache controller
may have issues (hardware deadlock) with the mandatory barriers (DSB
followed by an L2 cache sync) when ARM_DMA_MEM_BUFFERABLE is enabled.
The patch disables ARM_DMA_MEM_BUFFERABLE for these boards.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
RealView boards with certain revisions of the L220 cache controller (ARM11*
processors only) may have issues (hardware deadlock) with the recent changes to
the mb() barrier implementation (DSB followed by an L2 cache sync). The patch
redefines the RealView ARM11MPCore mandatory barriers without the outer_sync()
call.
Cc: <stable@kernel.org>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
CPU performance event counters on v7 cores will only operate
if either the NIDEN or DBGEN signals are driven high.
For the OMAP3 platform, these signals are driven low by default
but DBGEN can be asserted by selecting the OMAP3_EMU Kconfig option,
which enables the virtual clock for hardware debugging peripherals.
Acked-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Linux expects that if a CPU modifies a memory location, then that
modification will eventually become visible to other CPUs in the system.
On an ARM11MPCore processor, loads are prioritised over stores so it is
possible for a store operation to be postponed if a polling loop immediately
follows it. If the variable being polled indirectly depends on the outstanding
store [for example, another CPU may be polling the variable that is pending
modification] then there is the potential for deadlock if interrupts are
disabled. This deadlock occurs in the KGDB testsuire when executing on an
SMP ARM11MPCore configuration.
This patch changes the definition of cpu_relax() to smp_mb() for ARMv6 cores,
forcing a flushing of the write buffer on SMP systems before the next load
takes place. If the Kernel is not compiled for SMP support, this will expand
to a barrier() as before.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When not aligned, random bits could be written in the initial page table
by the __create_page_tables() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
workaround
Commit f4d6477f introduced a workaround for the lack of hardware
broadcasting of the cache maintenance operations on ARM11MPCore.
However, the workaround is only valid on CPUs that do not do speculative
loads into the D-cache.
This patch adds a Kconfig option with the corresponding help to make the
above clear. When the DMA_CACHE_RWFO option is disabled, the kernel
behaviour is that prior to the f4d6477f commit. This also allows ARMv6
UP processors with speculative loads to work correctly.
For other processors, a different workaround may be needed.
Cc: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
A recent patch for DMA cache maintenance on ARM11MPCore added a write
for ownership trick to the v6_dma_inv_range() function. Such operation
destroys data already present in the buffer. However, this function is
used with with dma_sync_single_for_device() which is supposed to
preserve the existing data transfered into the buffer. This patch adds a
combination of read/write for ownership to preserve the original data.
Reported-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This macro is not defined when !CONFIG_MMU so this patch moves the
CONSISTENT_* definitions to the CONFIG_MMU section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
arch/arm/mach-mx3/built-in.o: In function `mx31lilly_board_init':
mach-kzm_arm11_01.c:(.init.text+0x674): undefined reference to `otg_ulpi_create'
mach-kzm_arm11_01.c:(.init.text+0x68c): undefined reference to `otg_ulpi_create'
mach-kzm_arm11_01.c:(.init.text+0x744): undefined reference to `mxc_ulpi_access_ops'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP: hwmod: Fix the missing braces
OMAP4: clock: Fix multi-omap boot with reset un-used clocks
OMAP3: PM: fix IO daisy chain enable to use PM_WKEN reg
omap: GPIO: fix auto-disable of debounce clock
omap: DMTIMER: Ack pending interrupt always when stopping a timer
omap: Stalker board: switch over to gpio_set_debounce
omap: fix build failure due to missing include dma-mapping.h
omap iommu: Fix Memory leak
|
|
omap-fixes-for-linus
|
|
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
|
|
As reported by Sergei, a couple of braces were missing after
the WARN removal patch.
[07/22] OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
https://patchwork.kernel.org/patch/100756/
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: fixed patch description per Anand's E-mail]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
|
|
This patch uses "ENABLE_ON_INIT" flag on the emif clock nodes
to avoid the emif clk getting cut as part of reset un-used clock
routine which prevents boot.
Since "omap4xxx_clk_init()" calls "clk_enable_init_clocks()"
which increases the usecount on all ENABLE_ON_INIT clocks, it
prevents "omap2_clk_disable_unused()" from disabling the clock.
The real fix is to have driver for EMIF and do clock get/enable
as part of it. The EMIF driver is planned to be done HWMOD way
so till that available to keep omap3_defconfig booting on OMAP4430,
this patch is necessary.
(Will updated the auto-gen script for 44xx accordingly)
The fix was suggested by Paul Walmsley
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
PMU is not tested and enabled on MMP architecture at this moment,
the device IRQ number, IRQ_PMU depends on ARCH_PXA. Build PMU only
for ARCH_PXA.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Since commit a48c24a696f0d93c49f913b7818e9819612b1f4e, the
camera is not working anymore.
After the v4l2 migration, the mt9m111 camera board
information was not passed to the i2c layer anymore, but
stored for future use of v4l2 (through soc_camera).
Because mioa701_i2c_devices[] was tagged as "__initdata",
and because after the v4l2 migration, the new structure
"iclink" references it, the mt9m111 driver is not probed
anymore, as part of "iclink" is not valid (discarded after
kernel init).
Although there is not compilation error, nor runtime oops,
this patch restores a working camera on the mioa701 board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This patch fixes flash layout to it's final version. Also, I fixed the
authorship information of this file as it's been totally reworked since Ken
released his last version.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
gpio must be int, not u16, otherwise -1 isn't recognised
by gpio_is_valid().
Signed-off-by: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
|
|
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The addition of the new debounce code (commit
168ef3d9a56bd8bffe0ef4189c450888b4aefefe) broke the auto-disable of
debounce clocks on idle by forgetting to update the debounce clock
enable mask.
Add back the updating of bank->dbck_enable_mask so debounce clocks are
auto-disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The kernel timer queue is being run currently from a GP timer running in a one
shot mode, which works in a way that when it expires, it will also stop.
Usually during this situation, the interrupt handler will ack the interrupt,
load a new value to the timer and start it again. During suspend, the
situation is slightly different, as we disable interrupts just before
timekeeping is suspended, which leaves a small window where the timer can
expire before it is stopped, and will leave the interrupt flag pending.
This pending interrupt will prevent ARM sleep entry, thus now we ack it always
when we are attempting to stop a timer.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: removed the ifdef to make the patch cover omap1 also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 48feb337475a arm: omap: switch over to gpio_set_debounce caused
"undefined reference to omap_set_gpio_debounce" build error.
The fix is to use the generic gpiolib function.
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes following error,
CC arch/arm/mach-omap2/usb-ehci.o
arch/arm/mach-omap2/usb-ehci.c:263: error: implicit declaration of function
'DMA_BIT_MASK'
arch/arm/mach-omap2/usb-ehci.c:263: error: initializer element is not constant
make[1]: *** [arch/arm/mach-omap2/usb-ehci.o] Error 1
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The memory allocated for sgt structure is not freed on error
when sg_alloc_table is called in sgtable_alloc().
Signed-off-by: Satish Kumar <x0124230@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgen <tony@atomide.com>
|
|
When functions incoming parameters are not in input operands list gcc
4.5 does not load the parameters into registers before calling this
function but the inline assembly assumes valid addresses inside this
function. This breaks the code because r0 and r1 are invalid when
execution enters v4wb_copy_user_page ()
Also the constant needs to be used as third input operand so account
for that as well.
Tested on qemu arm.
CC: <stable@kernel.org>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
|
|
Instruction faults on pre-ARMv6 CPUs are interpreted as
a 'translation fault', but do_translation_fault doesn't
handle well if user mode trying to run instruction above
TASK_SIZE, and result in the infinite retry of that
instruction.
CC: <stable@kernel.org>
Signed-off-by: Anfei Zhou <anfei.zhou@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When CONFIG_DEBUG_HIGHMEM is used, the fixmap entry used for a highmem page
by kmap_atomic() is always cleared by kunmap_atomic(). This helps find
bad usages such as dereferences after the unmap, or overflow into the
adjacent fixmap areas.
But this debugging aid is completely bypassed when a kmap for the same
page already exists as the kmap is reused instead. ON VIVT systems we
have no choice but to reuse that kmap due to cache coherency issues,
but on non VIVT systems we should always force the fixmap usage when
debugging is active.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Currently compilation of ux500 fails if you deselect the kernel
feature for localtimers.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
At some point this was exposed (not sure how),
linux-2.6/arch/arm/mach-msm/dma.c:92: error: field 'complete' has incomplete type
linux-2.6/arch/arm/mach-msm/dma.c: In function 'dmov_exec_cmdptr_complete_func':
linux-2.6/arch/arm/mach-msm/dma.c:108: error: implicit declaration of function 'complete'
linux-2.6/arch/arm/mach-msm/dma.c: In function 'msm_dmov_exec_cmd':
linux-2.6/arch/arm/mach-msm/dma.c:120: error: implicit declaration of function 'init_completion'
linux-2.6/arch/arm/mach-msm/dma.c:123: error: implicit declaration of function 'wait_for_completion'
and the fix is just to add the header.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
|
|
This patch registers the WM8750 codec on a proper place on the SPITZ machine
after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
