Age | Commit message (Collapse) | Author |
|
Bandgap is a device used to measure temperature on electronic
equipments. It is widely used in digital integrated circuits. It is
based on the dependency between silicon voltage and temperature.
This patch introduce HAS_BANDGAP config entry. This config is a boolean
value so that arch code can flag if they feature a bandgap device.
This config entry follows the same idea behind ARCH_HAS_CPUFREQ.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Fabio Stevam <festevam@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When scheduling an mm on a CPU where it hasn't previously been used, we
flush the icache on that CPU so that any code loaded previously on
a different core can be safely executed.
For cores with hardware broadcasting of cache maintenance operations,
this is clearly unnecessary, since the inner-shareable invalidation in
__sync_icache_dcache will affect all CPUs.
This patch conditionalises the icache flush in switch_mm based on
cache_ops_need_broadcast().
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Albin Tonnerre <albin.tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When zImage is loaded into RAM at a low address but TEXT_OFFSET
is set higher, we risk overwriting ourself with the page table
needed to turn on the cache as it is located relative to the relocation
address. Let's defer the cache setup after relocation in that case.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Stephen Boyd <sboyd@codeurora.org>
Tested-by: Stephen Boyd <sboyd@codeurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
An exclusive store instruction may fail for reasons other than lock
contention (e.g. a cache eviction during the critical section) so, in
line with other architectures using similar exclusive instructions
(alpha, mips, powerpc), retry the trylock operation if the lock appears
to be free but the strex reported failure.
Reported-by: Tony Thompson <anthony.thompson@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Running an OABI_COMPAT kernel on an SMP platform can lead to fun and
games with page aging.
If one CPU issues a swi instruction immediately before another CPU
decides to mkold the page containing the swi instruction, then we will
fault attempting to load the instruction during the vector_swi handler
in order to retrieve its immediate field. Since this fault is not
currently dealt with by our exception tables, this results in a panic:
Unable to handle kernel paging request at virtual address 4020841c
pgd = c490c000
[4020841c] *pgd=84451831, *pte=bf05859d, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in: hid_sony(O)
CPU: 1 Tainted: G W O (3.4.0-perf-gf496dca-01162-gcbcc62b #1)
PC is at vector_swi+0x28/0x88
LR is at 0x40208420
This patch wraps all of the swi instruction loads with the USER macro
and provides a shared exception table entry which simply rewinds the
saved user PC and returns from the system call (without setting tbl, so
there's no worries with tracing or syscall restarting). Returning to
userspace will re-enter the page fault handler, from where we will
probably send SIGSEGV to the current task.
Reported-by: Wang, Yalin <yalin.wang@sonymobile.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the missing VPU devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The gpio-ranges properties in vf610.dtsi were written according to an
older version of the GPIO bindings. Unfortunately, these were changed
incompatibly in commit 86853c8 "gpio: add gpio offset in gpio range
cells property". This patch adds the missing required extra cell in each
gpio-ranges property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable WM8962 ALSA machine driver via devicetree.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable SSI2 and its pin configuration in AUDMUX.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add WM8962 CODEC support and enable its parent I2C bus.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a pinctrl for AUDMUX used on imx6dl-sabresd.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a pinctrl for I2C1 used on imx6q/dl-sabresd.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01).
- Module pfla02
- Carrier-Board pbab01
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a group to the usdhc2 and enet pinctrl.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds name for NOR flash. This keeps compatibility for
commandline partitions parsing from old bootloaders and make name
of device same for DT and non-DT boot.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds the SHDC devicetree node for PCM970 board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds the missing SDHC devicetree nodes for i.MX27 SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds the missing DMA devicetree node for i.MX27 SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable the WEIM NOR for imx6q{dl}-sabreauto boards.
For the pin conflict with SPI NOR, its status is set to "disabled".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add the clock and compatible information for the weim.
Also adds the weim label.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add missing pin config
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add properties to make use of pca9554 gpio expander.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable tve on MBa53.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add WP/CD pinctrl for esdhc2.
Also, add vmmc-supply for esdhc2.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
BIT(31) is NO_PAD_CTL, not BIT(16)
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It's active high, not active low.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add initial Freescale Vybrid VF610 Tower board support
with uart and fec enabled.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add SoC level device tree source for Freescale Vybrid VF610.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a group to the fec pinctrl, for use with MII interface.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add ecspi2 pinctrl.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add a group to the cspi pinctrl.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add support for CLAA WVGA display for i.MX53 QSB.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There is a redundant ocotp node. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|