| Age | Commit message (Collapse) | Author |
|---|
|
Set-associative caches on all v7 implementations map the index bits
to physical addresses LSBs and tag bits to MSBs. As the last level
of cache on current and upcoming ARM systems grows in size,
this means that under normal DRAM controller configurations, the
current v7 cache flush routine using set/way operations triggers a
DRAM memory controller precharge/activate for every cache line
writeback since the cache routine cleans lines by first fixing the
index and then looping through ways (index bits are mapped to lower
physical addresses on all v7 cache implementations; this means that,
with last level cache sizes in the order of MBytes, lines belonging
to the same set but different ways map to different DRAM pages).
Given the random content of cache tags, swapping the order between
indexes and ways loops do not prevent DRAM pages precharge and
activate cycles but at least, on average, improves the chances that
either multiple lines hit the same page or multiple lines belong to
different DRAM banks, improving throughput significantly.
This patch swaps the inner loops in the v7 cache flushing routine
to carry out the clean operations first on all sets belonging to
a given way (looping through sets) and then decrementing the way.
Benchmarks showed that by swapping the ordering in which sets and
ways are decremented in the v7 cache flushing routine, that uses
set/way operations, time required to flush caches is reduced
significantly, owing to improved writebacks throughput to the DRAM
controller.
Benchmarks results vary and depend heavily on the last level of
cache tag RAM content when cache is cleaned and invalidated, ranging
from 2x throughput when all tag RAM entries contain dirty lines
mapping to sequential pages of RAM to 1x (ie no improvement) when
all tag RAM accesses trigger a DRAM precharge/activate cycle, as the
current code implies on most DRAM controller configurations.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We have a handy macro to replace open coded __cpuc_flush_dcache_area(()
and outer_clean_range() sequences. Let's use it. No functional change.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Clean up the setup ARM printks a bit. Add printk level to a few
that were missing (CPU: <...> ones, in particular), and switch from
printk(KERN_* ..) to pr_*().
Finally, un-wrap some long lines since it makes it harder to grep the
sources from where an error came from and tweak some cases of indentation.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d0631001288a5974afc0b2a5f568bcdecb4d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The only v7-M platform only has some unused stubs in its
mach/entry-macro.S file. So don't include it which allows efm32 to drop
the file.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We don't need the offset for the first function name in each backtrace
entry; this needlessly consumes screen space. This is virtually always
the first or second instruction in the called function.
Also, recognise stmfd instructions which include r10 as a valid stack
saving instruction, and when dumping the registers, dump six registers
per line rather than five, and fix the wrapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ioremap_cache is more aligned with other architectures. There are only
2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64 caused by commit c04e8e2fe5 (arm64:
allow ioremap_cache() to use existing RAM mappings)
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Need a newer base version to get a regulator fix for Samsung platforms that
they enable building in a defconfig.
Linux 3.13-rc5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071b3d23f
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16eb8f0d0
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
After commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1ef130e8bf30bcd3e529b7f35112c503
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
Samsung cleanup 2nd for v3.14
- remove <mach/regs-clock.h> for exynos
- remove <mach/regs-irq.h> for exynos
- local <mach/regs-pmu.h> into mach-exynos
- select PM_GENERIC_DOMAINS for ARCH_EXYNOS4
instead of each SOC_EXYNOS4XXX in Kconfig
- call pm_genpd_poweroff_unused() instead of via
exynos_pm_late_initcall() because no need to
handle whether CONFIG_PM_GENERIC_DOMAINS is enalbed
* tag 'samsung-cleanup-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
ARM: EXYNOS: local definitions for cpuidle.c into mach-exynos dir
cpufreq: exynos: move definitions for exynos-cpufreq into drivers/cpufreq/
ARM: EXYNOS: local definitions for pm.c into mach-exynos dir
PM / devfreq: move definitions for exynos4_bus into drivers/devfreq
ARM: EXYNOS: cleanup <mach/regs-clock.h>
ARM: EXYNOS: cleanup <mach/regs-irq.h>
ARM: EXYNOS: local regs-pmu.h header file
ARM: EXYNOS: remove inclusion <mach/regs-pmu.h> into another headers
ARM: EXYNOS: cleanup <mach/regs-pmu.h>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mbus is the memory bus clock, and it is present on both sun5i and sun7i
machines. Its register layout is compatible with the mod0 one.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit adds all the mod0 clocks available on A20 to its device
tree. This list was created by looking at AW's code release.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit adds all the mod0 clocks available on A10 and A13. The list
has been constructed by looking at the Allwinner code release for A10S
and A13.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit adds all the mod0 clocks present on sun4i to its device tree
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit adds PLL5 and PLL6 nodes to the sun4i, sun5i and sun7i
device trees.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This commit adds the PLL4 definition to the sun4i, sun5i and sun7i
device trees. PLL4 is compatible with PLL1.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/boards
From Stephen Warren:
ARM: tegra: second set of defconfig changes
This branch contains changes to tegra_defconfig that came in after
I sent the previous pull-request/tag tegra-for-3.14-defconfig. We enable:
* DRM_PANEL/DRM_PANEL_SIMPLE, which implements the built-in LCD panel
support for Harmony, Cardhu, and Dalmore.
This branch is based on tag tegra-for-3.14-defconfig, for which I sent a
previous pull request.
* tag 'tegra-for-3.14-defconfig-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable DRM panel support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
From Stephen Warren:
ARM: tegra: second set of device tree changes
This branch contains changes to Tegra's device tree that came in after
I sent the previous pull-request/tag tegra-for-3.14-dt. Changes are:
* Set up aliases for RTCs, so that the correct RTC is chosen to
initialize the system date/time.
* Venice2 pinctrl and regulator configuration.
* Built-in panel enablement for Harmony, Cardhu, Dalmore.
* HDMI enablement for Dalmore.
* USB2 port enablement for Beaver.
* Keyboard and power key enablement for Venice2.
* tag 'tegra-for-3.14-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable power key on Venice2
ARM: tegra: Enable Venice2 keyboard
ARM: tegra: enable USB2 on Tegra30 Beaver
ARM: tegra: modify Tegra30 USB2 default phy_type to UTMI
ARM: tegra: Enable HDMI support on Dalmore
ARM: tegra: Enable DSI support on Dalmore
ARM: tegra: Add Tegra114 gr3d support
ARM: tegra: Add Tegra114 gr2d support
ARM: tegra: Add Tegra114 DSI support
ARM: tegra: Add host1x, DC and HDMI to Tegra114 device tree
ARM: tegra: Add MIPI calibration DT entries for Tegra114
ARM: tegra: Enable LVDS on Cardhu
ARM: tegra: Enable LVDS on Harmony
ARM: tegra: set up /aliases for RTCs on Venice2
ARM: tegra: add ams AS3722 device to Venice2 DT
ARM: tegra: fix missing pincontrol configuration for Venice2
ARM: tegra: set up /aliases entries for RTCs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
In preparation to the introduction of the support for additional SoC,
the mvebu/common.h should be clear of Armada 370/XP-specific
definitions. Therefore, move the Armada 370/XP SMP specific
definitions to the armada-370-xp.h file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The mach-mvebu/common.h file contains prototypes of functions that
have been removed, so this commit removes the corresponding
prototypes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
|
|
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8bed3e1 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/boards
From Stephen Warren:
ARM: tegra: defconfig changes
Enable new features required by the Venice2 board.
This branch is based on v3.13-rc1, and shouldn't cause any conflicts.
* tag 'tegra-for-3.14-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tegra_defconfig updates
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
This branch contains all the changes to Tegra's device tree. The
highlights are:
* Many patches for Tegra124 SoC support, and the Venice2 board which
uses that SoC.
* Conversion to use more headers providing named constants for pinctrl
and key codes, which improves readability.
* A few cleanups.
This branch is based on tag tegra-for-3.14-dmas-resets-rework in order
to avoid conflicts with the DT changes required to use the common
bindings for DMAs and resets.
* tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (24 commits)
ARM: tegra: Add SPI controller nodes for Tegra124
ARM: tegra: Fix misconfiguration of pin PH2 on Venice2
ARM: tegra: fix pinctrl misconfiguration on Venice2
ARM: tegra: add default pinctrl nodes for Venice2
ARM: tegra: correct Colibri T20 regulator settings
ARM: tegra: convert dts files of Tegra30 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra20 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra114 platforms to use pinctrl defines
ARM: tegra: Add header file for pinctrl constants
ARM: tegra: convert device tree files to use key defines
ARM: tegra: Enable PWM on Venice2
ARM: tegra: Add Tegra124 PWM support
ARM: tegra: add sound card to Venice2 DT
ARM: tegra: add audio-related device to Tegra124 DT
ARM: tegra: enable I2C controllers on Venice2
ARM: tegra: add I2C controllers to Tegra124 DT
ARM: tegra: add MMC controllers to Tegra124 DT
ARM: tegra: add Tegra124 pinmux node to DT
ARM: tegra: add APB DMA controller to Tegra124 DT
ARM: tegra: add reset properties to Tegra124 DTs
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
From Stephen Warren:
ARM: tegra: SoC-specific core code changes
This branch contains various miscellaneous changes to code in the
mach-tegra/ directory. It is baased on v3.13-rc1, and shouldn't conflict
with anything else.
* tag 'tegra-for-3.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: select PINCTRL_TEGRA124 for Tegra124 SoC
ARM: tegra: use section-sized static mappings for LPAE too
ARM: tegra: don't hard-code DEBUG_LL baud rate
ARM: tegra: fix DEBUG_LL combined with LPAE
ARM: tegra: switch FUSE clock on before usage
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
From Stephen Warren:
ARM: tegra: Trusted Foundations firmware support
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
(The base TF support has been discussed back and forth a lot; for now
the most logical place for it seems to be under arch/arm, so we're adding
it here. We can move it out to a common location in the future if needed).
* tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: support Trusted Foundations by default
ARM: tegra: set CPU reset handler using firmware
ARM: tegra: split setting of CPU reset handler
ARM: tegra: add support for Trusted Foundations
of: add Trusted Foundations bindings documentation
of: add vendor prefix for Trusted Logic Mobility
ARM: add basic support for Trusted Foundations
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
From Stephen Warren:
ARM: tegra: powergate driver changes
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
* tag 'tegra-for-3.14-powergate' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add IO rail support
ARM: tegra: Special-case the 3D clamps on Tegra124
ARM: tegra: Add Tegra124 powergate support
ARM: tegra: Export tegra_powergate_remove_clamping()
ARM: tegra: Export tegra_powergate_power_off()
ARM: tegra: Rename cpu0 powergate to crail
ARM: tegra: Fix some whitespace oddities
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Bringing in the tegra dma/reset rework as a base for new SoC branches.
* tegra/dma-reset-rework: (81 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Linux 3.13-rc4
|
|
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 4dcfa60071b3d23f0181f27d8519f12e37cefbb9 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This reverts commit b652896b02df3dfde3a68957cce01f2aa4585842.
Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This reverts commit 6dea2c1ebc6fc43852fd6125d75a75da223ff707.
Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c082 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).
Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
OMAP2 - GPMC, RNG
OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: Suman Anna <s-anna@ti.com>
Fixes: 7d7e1eba7e92 ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825ca31 ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Fixes: 7dedd346941d ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
As the davinci-gpio driver is migrated to use irqdomain
there is no need to pass the irq base for the gpio driver.
This patch removes this variable from davinci_gpio_platform_data
and also the refrences from the machine file.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB Ports
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This file is mainly a copy of kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the
number of GPIO available (36 on 6192, 50 on 6281).
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The per-CPU PMSU registers documented in the datasheet start at
0x22100 and the last register for CPU3 is at 0x22428. However, the DT
informations use <0x22100 0x430>, which makes the region end at
0x22530 and not 0x22430.
Moreover, looking at the datasheet, we can see that the registers for
CPU0 start at 0x22100, for CPU1 at 0x22200, for CPU2 at 0x22300 and
for CPU3 at 0x22400. It seems clear that 0x100 bytes of registers have
been used per CPU.
Therefore, this commit reduces the length of the PMSU per-CPU register
area from the incorrect 0x430 bytes to a more logical 0x400 bytes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ARMADA_XP_MAX_CPUS definition was in common.h, which as its name
says, is common to all mvebu SoCs. It is more logical to have this XP
specific definition in the already existing armada-370-xp.h header
file, especially in preparation to the addition of the support for
other SOCs in mach-mvebu.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
We need the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
