Age | Commit message (Collapse) | Author |
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Armadillo 800 EVA panel module has a backlight enable signal
connected to GPIO 61. Report this in the backlight DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 22ceeee16eb8f0d04de3ef43a5174fb30ec18af9 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator and reference it for the backlight
power supply.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
|
|
Fix a typo in the USBHS1 pinconf entry that prevented the pull-down from
being enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Let the multiplatform Koelsch support boot with the legacy DTS for
Koelsch as well as the Koelsch reference DTS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Let the multiplatform Lager support boot with the legacy DTS for Lager
as well as the Lager reference DTS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that r8a7791 has CCF support remove the legacy Koelsch reference
Kconfig bits CONFIG_MACH_KOELSCH_REFERENCE for the non-multiplatform
case.
Starting from this commit Koelsch board support is always enabled via
CONFIG_MACH_KOELSCH, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-koelsch.c and board-koelsch-reference.c
The file board-koelsch-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: Dropped arch/arm/boot/dts/Makefile portion]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that r8a7790 has CCF support remove the legacy Lager reference
Kconfig bits CONFIG_MACH_LAGER_REFERENCE for the non-multiplatform
case.
Starting from this commit Lager board support is always enabled via
CONFIG_MACH_LAGER, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-lager.c and board-lager-reference.c
The file board-lager-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that the common clock framework is supported, the clock lookup
entries in clock-r8a7791.c are not registered anymore. Devices must
instead reference their clocks in the device tree. However, SCIF and CMT
devices are still instantiated through platform code, and thus need a
clock lookup entry.
Retrieve the SCIF and CMT clock entries by name and register clkdevs for
the corresponding devices. This will be removed when the SCIF and CMT
devices will be instantiated from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Now that the common clock framework is supported, the clock lookup
entries in clock-r8a7790.c are not registered anymore. Devices must
instead reference their clocks in the device tree. However, SCIF and CMT
devices are still instantiated through platform code, and thus need a
clock lookup entry.
Retrieve the SCIF and CMT clock entries by name and register clkdevs for
the corresponding devices. This will be removed when the SCIF and CMT
devices will be instantiated from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The common clock framework is initialized in the rcar_gen2_init_timer()
function, remove the of_clk_init() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Enable multiplaform ARM architecture support for the Lager reference
board. Common clock framework initialization will be handled by the
rcar_gen2_init_timer() call, we just need to remove the legacy clock
code initialization.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The Armadillo 800 EVA panel module has a backlight enable signal
connected to GPIO 61. Instead of requesting the GPIO in board code and
setting it to a high level unconditionally, pass the GPIO number to the
PWM backlight driver as the backlight enable GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Register Ether platform device and pin data on the Koelsch board.
Register platform fixup for Micrel KSZ8041 PHY, just like on the Lager board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Only the LVDS output is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
|
|
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.
Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: William Towle <william.towle@codethink.co.uk>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
4dcfa60071b3d23f0181f27d8519f12e37cefbb9
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch
asoc-simple-card asoc-simple-card.0: \
Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
CONFIG_INOTIFY_USER and CONFIG_UNIX are required for udev to function.
This change brings the koelsch defconfig into line with
other shmobile defconfigs.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
CONFIG_PACKET is required for the ISC dhcpd daemon function.
This change brings the koelsch defconfig into line with
other shmobile defconfigs.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Linux 3.13-rc3
Conflicts:
drivers/pinctrl/sh-pfc/pfc-r8a7740.c
drivers/pinctrl/sh-pfc/pfc-sh7372.c
|
|
into dt3-base
|
|
When CONFIG_COMMON_CLOCK is enabled, call rcar_gen2_clocks_init() in the
timer init function to initialize the common clock framework before
initializing the clock sources. This will take care of clock
initialization when the r8a779[01] boards will be switched to
multiplatform kernels.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit 22ceeee16eb8f0d04de3ef43a5174fb30ec18af9 ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The backlight is controlled by a PWM signal generated by the TPU.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for CompuLab SBC-T3530, also known as cm-t3730:
http://compulab.co.il/products/sbcs/sbc-t3530/
It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:
http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/
So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.
I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.
Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.
Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This ensures that the PMIC RTC provides the system time, rather than
the on-SoC RTC, which is not battery-backed.
tegra124-venice2.dts isn't touched yet since we haven't added any off-
SoC RTC device to its device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This moves definitions for cpuidle into mach-exynos/cpuidle.c,
because we don't need to keep them in the <mach/regs-clock.h>.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This moves regarding exynos-cpufreq definitions into drivers/cpufreq/
exynos-cpufreq.h because they are used only for the cpufreq driver.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some of definitions in the regs-clock.h are used only for pm.c,
so this moves them into the file.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
We don't need to keep the definitions for exynos4_bus into
mach-exynos/ so this moves them into drviers/devfreq with
adding header file.
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Remove useless definitions in the regs-clock.h file.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Remove useless inclusion <mach/regs-irq.h> for exynos.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This moves regs-pmu.h file into mach-exynos directory.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This is needed to remove dependency of headers.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Remove useless definitions in the regs-pmu.h file.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
According to board schematics, for HSMMC1 a GPIO line is used to detect
card presence, while currently it is being configured for internal card
detect line, which is multiplexed with card detect line of HSMMC0 and
thus breaking it.
This patch adds proper sdhci platform data setting card detect type to
external GPIO and fixing operation of HSMMC0.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable clock binding for Hi3620 common clock driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Enable hotplug support on hi3xxx platform
How to test:
cat proc/interrupts
echo 0 > /sys/devices/system/cpu/cpuX/online
cat proc/interrupts
echo 1 > /sys/devices/system/cpu/cpuX/online
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Zhang Mingjun <zhang.mingjun@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
[khilman: fixed checkpatch error]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Enable SMP support on hi3xxx platform
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Zhang Mingjun <zhang.mingjun@linaro.org>
Tested-by: Li Xin <li.xin@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
[khilman: fix checkpatch errors]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add default config for arch-hi3xxx. It's used for Hisilicon Hi3xxx SoC.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Enable ARCH_HI3xxx in multi_v7_defconfig.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Enable Hisilicon Hi4511 development platform with device tree support.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|