Age | Commit message (Collapse) | Author |
|
The SIC is cascaded off the PIC, so specify this in the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
into next/soc
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Rebuild bcm2835_defconfig using "make bcm2835_defconfig;
make savedefconfig", and add the following features:
* Enable the DWC2 USB controller present in the BCM2835 SoC.
* Enable drivers for various USB-hosted devices, which make the
controller useful.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The BCM2835 SoC contains a DWC2 USB controller. Add this to the DT.
Set up the pin controller to fully enable the USB controller on the
Raspberry Pi. The GPIO setup works because the default output value for
GPIO 6 (LAN_RUN/n_reset) just happens to be 1, which enables the
USB/LAN chip.
Note that you'll need a U-Boot which enables power to the USB controller;
search for U-Boot patch "ARM: rpi_b: power on SDHCI and USB HW modules".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Replace "is use" by "is used" and remove a comma.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Maxime Ripard:
Allwinner sunXi DT Additions for 3.14
Various DT related patches, but mostly:
- Support for the Olimex A13-olinuxino-micro
- Added the needed IP in the A31 for the HS timer support and SMP bringup
- A10 and A20 RTC
* tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: dt: Add IP needed to bring up the additional cores
ARM: dts: sun5i: Add new sun5i-a13-olinuxino-micro board
ARM: sun6i: Add the reset controller to the DTSI
ARM: sunxi: dt: add EMAC aliases
ARM: dts: sun4i/sun7i: add RTC node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/fixes-non-critical
From Linus Walleij:
Misc U300 development for the v3.14 series:
- Timekeeping patch from Uwe.
- DT 0x0 cleanup from Lee.
- Return value check from Wei.
* tag 'u300-for-arm-soc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u300: fix timekeeping when periodic mode is used
ARM: u300: Remove '0x's from U300 DTS file
ARM: u300: fix return value check in __u300_init_boardpower()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/cleanup
From Jason Cooper:
mvebu SoC changes for v3.14 (incremental #2)
- mvebu
- some Armada cleanup to prep for a new SoC in mach-mvebu/
* tag 'mvebu-soc-3.14-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Second Round of Renesas ARM based SoC Board updates for v3.14
* r8a7791 (R-Car M2) based Koelsch board
- Let Koelsch multiplatform boot with Koelsch DTB
- Remove non-multiplatform DT reference support
- Instantiate clkdevs for SCIF and CMT
- Remove duplicate CCF initialization
- Add Ether and DU support
* r8a7790 (R-Car H2) based Lager board
- Let Lager multiplatform boot with Lager DTB
- Remove non-multiplatform DT reference support
- Instantiate clkdevs for SCIF and CMT
- Enable multiplaform kernel support
* r8a7740 (R-Mobile A1) based Armadillo board
- Set backlight enable GPIO
* sh7374 (SH-Mobile AP4) based Mackerel board
- Correct USBHS pinconf entry
* tag 'renesas-boards2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (25 commits)
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
ARM: shmobile: koelsch: Add DU device
arm: shmobile: clks: remove duplicated clock from r7s72100
ARM: shmobile: koelsch: Conditionally select MICREL_PHY
ARM: shmobile: rcar-gen2: Initialize CCF before clock sources
ARM: shmobile: r8a7791: Add clock index macros for DT sources
ARM: shmobile: r8a7790: Add clock index macros for DT sources
ARM: shmobile: Add select MIGHT_HAVE_PCI for PCI-AHB bridge code
ARM: shmobile: r8a7778: add USB Func DMAEngine support
ARM: rcar-gen2: Do not setup timer in non-secure mode
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* qcom/boards:
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: msm: trout: fix uninit var warning
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch enables MSM8974 build support.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds basic board support for APQ8074 Dragonboard
which belongs to the Snapdragon 800 family.
For now, just support a basic machine with device tree.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
[olof: Split off SoC and board support in separate patches]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Jason Cooper:
mvebu DT changes for v3.14 (incremental #5)
- mvebu
- add rtc chip isl12057 node to ReadyNAS boards
- fix register length in Armada XP pmsu
- kirkwood
- sort ocp nodes by address in 6282 dtsi file
- add 6192 dtsi file
- add LaPlug board
- add sata phy node
- dove
- add sata phy node
* tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu:
ARM: Kirkwood: DT board setup for LaPlug
ARM: Kirkwood: Add 6192 DTSI file
ARM: mvebu: fix register length for Armada XP PMSU
ARM: kirkwood: 6282: sort DT nodes by address
Phy: Add DT nodes on kirkwood and Dove for the SATA PHY
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 2120 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 104 .dts file
ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 102 .dts file
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Third Round of Renesas ARM based SoC Fixes for v3.13
* sh7372 (SH-Mobile AP4) based Mackerel board
r8a773a0 (SH-Mobile AG5) based kzm9g board
r8a7740 (R-Mobile A1) based Armadillo board
- Correct coherent DMA mask
This resolves regressions introduced by 4dcfa60071b3d23f
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* tag 'renesas-fixes3-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: mackerel: Fix coherent DMA mask
ARM: shmobile: kzm9g: Fix coherent DMA mask
ARM: shmobile: armadillo: Fix coherent DMA mask
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Third Round of Renesas ARM Based SoC Updates for v3.14
* Global
- Don't set plat_sci_port scbrr_algo_id field
- Declare SCIF register base and IRQ as resources
- Don't define SCIF platform data in an array
- Use macros to declare SCIF devices
* r7s72100 SoC (RZ/A1H)
- Add i2c clocks
* r8a7778 (R-Car M1)
- Add sound SCU clock support
* tag 'renesas-soc3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
arm: shmobile: r7s72100: add i2c clocks
ARM: shmobile: r8a7791: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7779: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7790: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7740: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a73a4: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7778: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r7s72100: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: sh73a0: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7790: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7791: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7778: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh7372: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7779: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7740: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a73a4: Declare SCIF register base and IRQ as resources
ARM: shmobile: r7s72100: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh73a0: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh7372: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7790: Don't define SCIF platform data in an array
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* qcom/dt:
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: msm: trout: fix uninit var warning
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* qcom/soc:
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: msm: trout: fix uninit var warning
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* qcom/fixes:
ARM: msm: trout: fix uninit var warning
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the mmio architected timer node.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This doesn't need to be a def_bool y. Instead we can have every
DT supported platform select ARCH_MSM_DT and we achieve the same
thing with less chance of conflicts.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the restart node so we can reboot the device.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for the Snapdragon 800 MSM8974 SoC, used on the Dragonboard
and others. Board support added in separate patch.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
[olof: split off SoC support in separate patch]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fix the following warning when !CONFIG_MMC:
arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:67:6: warning: unused variable 'rc' [-Wunused-variable]
int rc;
^
Also, while we're here, rework explicit printk(KERN_CRIT..) to use
pr_crit.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
'asoc/topic/adav80x', 'asoc/topic/adsp', 'asoc/topic/ak4641', 'asoc/topic/ak4642', 'asoc/topic/arizona', 'asoc/topic/atmel', 'asoc/topic/au1x', 'asoc/topic/axi', 'asoc/topic/bcm2835', 'asoc/topic/blackfin', 'asoc/topic/cs4271', 'asoc/topic/cs42l52', 'asoc/topic/da7210', 'asoc/topic/davinci', 'asoc/topic/ep93xx', 'asoc/topic/fsl', 'asoc/topic/fsl-mxs', 'asoc/topic/generic', 'asoc/topic/hdmi', 'asoc/topic/jack', 'asoc/topic/jz4740', 'asoc/topic/max98090', 'asoc/topic/mxs', 'asoc/topic/omap', 'asoc/topic/pxa', 'asoc/topic/rcar', 'asoc/topic/s6000', 'asoc/topic/sai', 'asoc/topic/samsung', 'asoc/topic/sgtl5000', 'asoc/topic/spear', 'asoc/topic/ssm2518', 'asoc/topic/ssm2602', 'asoc/topic/tegra', 'asoc/topic/tlv320aic3x', 'asoc/topic/twl6040', 'asoc/topic/txx9', 'asoc/topic/uda1380', 'asoc/topic/width', 'asoc/topic/wm8510', 'asoc/topic/wm8523', 'asoc/topic/wm8580', 'asoc/topic/wm8711', 'asoc/topic/wm8728', 'asoc/topic/wm8731', 'asoc/topic/wm8741', 'asoc/topic/wm8750', 'asoc/topic/wm8753', 'asoc/topic/wm8776', 'asoc/topic/wm8804', 'asoc/topic/wm8900', 'asoc/topic/wm8901', 'asoc/topic/wm8940', 'asoc/topic/wm8962', 'asoc/topic/wm8974', 'asoc/topic/wm8985', 'asoc/topic/wm8988', 'asoc/topic/wm8990', 'asoc/topic/wm8991', 'asoc/topic/wm8994', 'asoc/topic/wm8995', 'asoc/topic/wm9081' and 'asoc/topic/x86' into asoc-next
|
|
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This commit adds the two external clock outputs available on A20 to
its device tree. A dummy fixed factor clock is also added to serve as
the first input of the clock outputs, which according to AW's A20 user
manual, is the 24MHz oscillator divided by 750.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal into soc-thermal
|
|
Device tree naming conventions state that node names should match
the nodes function. Change external low speed oscillator node name
to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds the clock output pin options on the A20.
The 2 pins can output a configurable clock to be used by
external modules. This is used on the CubieTruck, to supply
a 32768 Hz low power clock to the onboard Wifi+BT module.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
On Allwinner sun7i (A20) SoCs, the SMP operations are implemented in
u-boot, and exposed to the kernel through PSCI.
We thus need to enable PSCI support for Allwinner SoCs so that the
kernel uses it to bring up the additionnal cores.
Signed-off-by: Signed-off-by: Zalan Blenessy <zalan.blenessy@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The current code selects ARCH_HAS_RESET_CONTROLLER, that enables the
RESET_CONTROLLER option by default, but doesn't select it, so a configuration
might unselect it, leading to compilation error.
Explictly select RESET_CONTROLLER so that we can't have this breakage anymore.
Reported-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
plat/regs-ata.h is used only by Samsung PATA driver.
Move this file to the drivers folder to remove platform
dependency required for multiplatform support.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Improve the comment of SW workaround for CCM lpm issue using
hardware errata description to avoid confusion.
ERR007265: CCM: When improper low-power sequence is used, the SoC
enters low power mode before the ARM core executes WFI.
Software workaround:
1) Software should trigger IRQ #32 (IOMUX) to be always pending
by setting IOMUX_GPR1_GINT.
2) Software should then unmask IRQ #32 in GPC before setting CCM
Low-Power mode.
3) Software should mask IRQ #32 right after CCM Low-Power mode is
set (set bits 0-1 of CCM_CLPCR).
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
For ccm clock gate, both 2b'11 and 2b'01 should be treated
as clock enabled, see below description in CCM, whenver CPU
trys to check clock gate's status, system will be in run mode.
2b'00: clock is off during all modes;
2b'01: clock is on in run mode, but off in wait and stop mode;
2b'10: Not applicable;
2b'11: clock is on during all modes, except stop mode.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Common clk framework will disable unused clks in late init only if
they are enabled by default and no one is using it, so we need to
add is_enabled callback for clk framework to get clks' status.
PFD clocks are enabled by hardware reset, so we need to add
interface for common clk framework to disable those unused ones for
saving power.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
PFUZE100 regulator is commonly found on mx6 based designs.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Let MX35 and MX50 device tree support be built by default.
Generated by doing:
- Selected CONFIG_MACH_IMX35_DT and CONFIG_SOC_IMX50 via 'make menuconfig'
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v6_v7_defconfig
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Re-using iMX6Q driver for cpu frequency scaling.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Cc: linux-arm-kernel@lists.infradead.org
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Update the IMX v6/v7 defconfig for the SolidRun HummingBoard:
- Add AT803X ethernet phy
- Add consumer IR devices
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
We are missing spba clock in imx6sl's clock tree, thus add it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There's a dividor for pll4_audio clock missing in clock tree, thus add it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
SPDIF can derive a TX clock for playback from one of its clock sources --
spdif root clock to match its supporting sample rates. So this patch set
the spdif root clock's parent to pll3_pfd3_454m since the pll3_pfd3_454m
can approximately meet its sample rate requirement.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|