summaryrefslogtreecommitdiffstats
path: root/arch/arm
AgeCommit message (Collapse)Author
2010-02-10OMAP: hsmmc: fix memory leakAaro Koskinen
The platform data allocated with kmalloc() will become unreachable once the init is complete, so it should be freed. The problem was discovered by kmemleak. Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Acked-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-04Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: ARM: Fix wrong register in proc-arm6_7.S data abort handler ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2 ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board mx35: add a missing comma in a pad definition mx25: make the FEC AHB clk secondary of the IPG mx25: fix time accounting mx25: properly initialize clocks mx25: remove unused mx25_clocks_init() argument i.MX25: implement secondary clocks for uarts and fec i.MX25: Allow secondary clocks in DEFINE_CLOCK ARM: MX3: Fixed typo in declared enum type name. MXC: Add AUDMUXv2 register decode to debugfs mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module mx31ads: Provide a name for EXPIO interrupt chip mx31ads: Allow enable/disable of switchable supplies
2010-02-03omap: Disable serial port autoidle by defaultTony Lindgren
Currently the omap serial clocks are autoidled after 5 seconds. However, this causes lost characters on the serial ports. As this is considered non-standard behaviour for Linux, disable the timeout. Note that this will also cause blocking of any deeper omap sleep states. To enable the autoidling of the serial ports, do something like this for each serial port: # echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout # echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout ... Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03omap: Fix access to already released memory in clk_debugfs_register_one()Marek Skuczynski
I have found an access to already released memory in clk_debugfs_register_one() function. Signed-off-by: Marek Skuczynski <mareksk7@gmail.com> Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03omap: Fix arch/arm/mach-omap2/mux.c: Off by one errorTony Lindgren
David Binderman ran the sourceforge tool cppcheck over the source code of the new Linux kernel 2.6.33-rc6: [./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds 13 characters + 1 digit + 1 zero byte is more than 14 characters. Also add a comment on mode0 name length in case new omaps start using longer names. Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03omap: Fix 3630 mux errorsTony Lindgren
3630 has more mux signals than 34xx. The additional pins exist in omap36xx_cbp_subset, but are not initialized as the superset is missing these offsets. This causes the following errors during the boot: mux: Unknown entry offset 0x236 mux: Unknown entry offset 0x22e mux: Unknown entry offset 0x1ec mux: Unknown entry offset 0x1ee mux: Unknown entry offset 0x1f4 mux: Unknown entry offset 0x1f6 mux: Unknown entry offset 0x1f8 mux: Unknown entry offset 0x1fa mux: Unknown entry offset 0x1fc mux: Unknown entry offset 0x22a mux: Unknown entry offset 0x226 mux: Unknown entry offset 0x230 mux: Unknown entry offset 0x22c mux: Unknown entry offset 0x228 Fix this by adding the missing offsets to omap3 superset. Note that additionally the uninitialized pins need to be skipped on 34xx. Based on an earlier patch by Allen Pais <allen.pais@ti.com>. Reported-by: Allen Pais <allen.pais@ti.com> Signed-off-by: Allen Pais <allen.pais@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03OMAP2/3: GPMC: ensure valid clock pointerKevin Hilman
Ensure valid clock pointer during GPMC init. Fixes compiler warning about potential use of uninitialized variable. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03OMAP2/3: IRQ: ensure valid base addressKevin Hilman
Ensure valid base address during IRQ init. Fixes compiler warning about potential use of uninitialized variable. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03ARCH OMAP : enable ARCH_HAS_HOLES_MEMORYMODEL for OMAPSriram
OMAP platforms(like OMAP3530) include DSP or other co-processors for media acceleration. when carving out memory for the accelerators we can end up creating a hole in the memory map of sort: <kernel memory><hole(memory for accelerator)><kernel memory> To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL has to be enabled. For further information refer discussion at: http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html. Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03omap: Remove old unused defines for OMAP_32KSYNCT_BASETony Lindgren
Remove old unused defines for OMAP_32KSYNCT_BASE Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-03ARM: Fix wrong register in proc-arm6_7.S data abort handlerRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-01Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6Russell King
2010-02-01ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptionsCatalin Marinas
Commit c98929c07a removed the clearing of the FPSCR[31:28] bits from the vfp_raise_exceptions() function and the new bits are or'ed with the old FPSCR bits leading to unexpected results (the original commit was referring to the cumulative bits - FPSCR[4:0]). Reported-by: Tom Hameenanttila <tmhameen@marvell.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-30ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2Catalin Marinas
Current behaviour is to generate the IT instruction only for Thumb-2 code. However, the kernel helpers in entry-armv.S are compiled to ARM in a unified syntax file (if THUMB2_KERNEL). Recent compilers warn about missing IT instruction in unified assembly syntax files. The patch changes the "-mimplicit-it" gas option to "always". Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-30ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development boardColin Tuckley
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-29omap: define _toggle_gpio_edge_triggering only for OMAP1Uwe Kleine-König
The only usage of _toggle_gpio_edge_triggering is in an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if CONFIG_ARCH_OMAP1 is defined, too. This fixes a compiler warning: arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-29mx35: add a missing comma in a pad definitionUwe Kleine-König
Reported-by: Tim Sander <tstone@vlsi.informatik.tu-darmstadt.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-28[ARM] Update mach-typesRussell King
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-28Merge branch 'fix' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6
2010-01-27Merge branch 'for-rmk' of git://git.marvell.com/orionRussell King
2010-01-26mx25: make the FEC AHB clk secondary of the IPGBaruch Siach
This makes the FEC clock configuration consistent with the UART one. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-26mx25: fix time accountingBaruch Siach
The gpt_clk rate function doesn't consider the PER divider. This causes a significant drift in time accounting. Fix this by introducing the correct rate calculation function. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-26mx25: properly initialize clocksBaruch Siach
This patch disables all unnecessary clock in mx25_clocks_init() to make a clean start, the same as is being done for the rest of the i.MX chips. This patch was tested on i.MX25 PDK. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-26mx25: remove unused mx25_clocks_init() argumentBaruch Siach
The fref is needless on mx25 since the reference clock is fixed at 24MHz. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-26i.MX25: implement secondary clocks for uarts and fecSascha Hauer
For uarts and fec need two clocks, implement it using the secondary clock field in struct clk. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-26i.MX25: Allow secondary clocks in DEFINE_CLOCKSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-25Merge branch 'omap-fixes-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (25 commits) OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timer PM debug: Fix warning when no CONFIG_DEBUG_FS OMAP3: PM: DSS PM_WKEN to refill DMA OMAP: timekeeping: time should not stop during suspend OMAP3: PM: Force write last pad config register into save area OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get() OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modules OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FS OMAP3: PM: Removing redundant and potentially dangerous PRCM configration OMAP3: Fixed ARM aux ctrl register save/restore OMAP3: CPUidle: Fixed timer resolution OMAP3: PM: Remove duplicate code blocks OMAP3: PM: Disable interrupt controller AUTOIDLE before WFI OMAP3: PM: Enable system control module autoidle OMAP3: PM: Ack pending interrupts before entering suspend omap: Enable GPMC clock in gpmc_init OMAP1 clock: fix for "BUG: spinlock lockup on CPU#0" OMAP4: clocks: Fix the clksel_rate struct DPLL divs OMAP4: PRCM: Fix the base address for CHIRONSS reg defines OMAP: dma_chan[lch_head].flag & OMAP_DMA_ACTIVE tested twice in omap_dma_unlink_lch() ...
2010-01-24[ARM] orion5x: D-link DNS-323 rev. B1 power-offErik Benada
This patch fixes power LED blinking and power-off on DNS-323 rev. B1. GPIO pin 3 has to be set to 1 to stop power LED blinking and to allow the LED to be controlled via leds-gpio. This pin has to be also set to 1 for power-off to work. To power-off the rev. B1 machine, pin 8 has to be set to 1 and then set to 0 to do actual power-off. Tested on my DNS-323 rev. B1 Signed-off-by: Erik Benada <erikbenada@yahoo.ca> Signed-off-by: Nicolas Pitre <nico@marvell.com>
2010-01-21OMAP2/3: DMTIMER: Clear pending interrupts when stopping a timerTero Kristo
OMAP GP timers keep running for a few cycles after they are stopped, which can cause the timer to expire and generate an interrupt. The pending interrupt will prevent e.g. OMAP from entering suspend, thus we ack it manually. Only applicable on OMAP2/3/4. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-01-21Merge branch 'for-linus/samsung' of git://git.fluff.org/bjdooks/linuxLinus Torvalds
* 'for-linus/samsung' of git://git.fluff.org/bjdooks/linux: hmt: adjust for new pwm_backlight->notify prototype
2010-01-22hmt: adjust for new pwm_backlight->notify prototypePeter Korsgaard
Commit cfc38999f (backlight: Pass device through notify callback) added a struct device argument to the notify callback, but didn't update the user of it in mach-hmt.c Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-01-21Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot() ARM: 5884/1: arm: Fix DCC console for v7 ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels" ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void) ARM: fix badly placed mach/plat entries in Kconfig & Makefile
2010-01-21ARM: MX3: Fixed typo in declared enum type name.Vladimir Zapolskiy
To distinguish between mx31lite and mx31lilly boards better to use different enum types. Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com> Acked-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-01-20Merge branch 'omap-fixes' into omap-fixes-for-linusTony Lindgren
2010-01-20Merge branch 'pm-fixes' of ↵Tony Lindgren
master.kernel.org:/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-fixes-for-linus
2010-01-20PM debug: Fix warning when no CONFIG_DEBUG_FSSergio Aguirre
Fix following warning when CONFIG_DEBUG_FS wasn't selected: arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: DSS PM_WKEN to refill DMASubramani Venkatesh
Currently, DSS does not wakeup when there is a DMA request. DSS wake up event must be enabled so that the DMA request to refill the FIFO will wake up the CORE domain. Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP: timekeeping: time should not stop during suspendKevin Hilman
During suspend, the kernel timekeeping subsystem is shut down. Before suspend and upon resume, it uses a weak function read_persistent_clock() to determine the amount of time that elapsed during suspend. This function was not implemented on OMAP, so from the timekeeping subsystem perspective (and thus userspace as well) it appeared that no time elapsed during suspend. This patch uses the 32k sync timer as a the persistent clock. NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so more than one wrapping of the 32k sync timer during suspend may cause problems. Also note there are not interrupts when the 32k sync timer wraps, so something else has to be done. Reported-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Force write last pad config register into save areaTero Kristo
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register (ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous OCP access to the SCM register area. Fixed by writing the last register to the save area. Also, optimized the delay loop for the HW save to include an udelay(1), which limits the number of unnecessary HW accesses to SCM register area during the save. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP: omap3_pm_get_suspend_state() error ignored in pwrdm_suspend_get()Roel Kluin
val is an u64 pointer, we need an int to check the error. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Enable wake-up from McBSP2, 3 and 4 modulesPeter Ujfalusi
Wake-up from McBSP ports are needed, especially when the THRESHOLD dma mode is in use for audio playback. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM debug: fix build error when !CONFIG_DEBUG_FSManjunatha GK
The PM debug code fails to build on when CONFIG_DEBUG_FS is not enabled. Build error log: arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle': arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save' arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save' arch/arm/mach-omap2/built-in.o: In function `configure_vc': arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init' arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init' make: *** [.tmp_vmlinux1] Error 1 This patch fixes the above errors. Kernel booting is tested on omap zoom2 and zoom3 boards. Signed-off-by: Manjunatha GK <manjugk@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Removing redundant and potentially dangerous PRCM configrationSripathy, Vishwanath
As part of Core domain context restoration while coming out of off mode there are some registers being restored which are not required to be restored. ROM code will have restored them already. Overwriting some of them can have potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked. Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled. Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: Fixed ARM aux ctrl register save/restoreTero Kristo
Current value is stored on SDRAM and it is written back during wakeup. Previously a static value of 0x72 was written there. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Acked-by: Thara Gopinath <thara@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: CPUidle: Fixed timer resolutionTero Kristo
Previously used u32 as temporary data storage that wraps around at 4.294s. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Remove duplicate code blocksSanjeev Premi
This patch removes code blocks that are repeated in function prcm_setup_regs(). Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Disable interrupt controller AUTOIDLE before WFITero Kristo
OMAP interrupt controller goes to unknown state when there is right combination of l3,l4 sleep/wake-up transitions, l4 autoidle in interrupt controller and some interrupt. When this happens, interrupts are not delivered to ARM anymore and ARM will remain in WFI (wait for interrupt) until interrupt controller is forced to wake-up (i.e. lauterbach). Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Enable system control module autoidleTero Kristo
Enable the auto-idle feature of the SCM block to save some additional power. Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20OMAP3: PM: Ack pending interrupts before entering suspendTero Kristo
Suspending drivers may still generate interrupts just before their suspend is completed. Any pending interrupts here will prevent sleep. Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-01-20omap: Enable GPMC clock in gpmc_initOlof Johansson
Don't assume that gpmc_l3_clk is on, enable it before touching configuration registers. Note that the current code assumes that this clock is always enabled. We are already setting smart idle and L3 autogating for GPMC clock in gpmc_init. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Tony Lindgren <tony@atomide.com>