| Age | Commit message (Collapse) | Author |
|---|
|
Redefine IRQ_MCT_L0,1 irq definition as it is changed in rev1 of EXYNOS5.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Adapt to changes in GIC physical address in rev1 of EXYNOS5.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add watchdog timer clock instance for EXYNOS5 watchdog controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
|
|
Since just plat-samsung can support all of Samsung stuff so
that there is no more need to keep the plat-s5p for S5P SoCs.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
|
|
It should be (1 << 2) for ctrlbit of exynos5_clk_pdma1.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into fixes
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.
Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"Things have slowed down a lot for us, but we have five more fixes for
omap and kirkwood below. Three are for boards setup issues, two are
SoC-level fixes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: igep0020: fix smsc911x dummy regulator id
ARM: orion5x: Fix GPIO enable bits for MPP9
ARM: kirkwood: add missing kexec.h include
ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fix two board spefific regressions and one regression caused by bad documentation
By Archit Taneja (1) and others
via Tony Lindgren
* tag 'omap-fixes-for-v3.4-rc6-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: igep0020: fix smsc911x dummy regulator id
ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler
|
|
id 0 is already used and causes errors at boot:
WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'
Fix it by using the next available one (id=1).
This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.
Signed-off-by: Enrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 554cdaefd1cf7bb54b209c4e68c7cec87ce442a9 ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only). For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:
[ 12.711476] leds-gpio: probe of leds-gpio failed with error -22
Reported-by: Henry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [v3.0+]
Tested-by: Hans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Fixes the following build error when CONFIG_KEXEC is enabled:
CC arch/arm/mach-kirkwood/board-dt.o
arch/arm/mach-kirkwood/board-dt.c: In function 'kirkwood_dt_init':
arch/arm/mach-kirkwood/board-dt.c:52:2: error: 'kexec_reinit' undeclared (first use in this function)
arch/arm/mach-kirkwood/board-dt.c:52:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
[v4, rebase onto recent Linus for repost]
[v3, speak actual English in the commit message, thanks Sergei Shtylyov]
[v2, using linux/kexec.h not asm/kexec.h]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 4e8ee7de227e3ab9a72040b448ad728c5428a042 (ARM: SMP: use
idmap_pgd for mapping MMU enable during secondary booting)
switched secondary boot to use idmap_pgd, which is initialized
during early_initcall, instead of a page table initialized during
__cpu_up. This causes idmap_pgd to contain the static mappings
but be missing all dynamic mappings.
If a console is registered that creates a dynamic mapping, the
printk in secondary_start_kernel will trigger a data abort on
the missing mapping before the exception handlers have been
initialized, leading to a hang. Initial boot is not affected
because no consoles have been registered, and resume is usually
not affected because the offending console is suspended.
Onlining a cpu with hotplug triggers the problem.
A workaround is to the printk in secondary_start_kernel until
after the page tables have been switched back to init_mm.
Cc: <stable@vger.kernel.org>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The machine endianness has no direct correspondence to the syscall ABI,
so use only AUDIT_ARCH_ARM when identifying the ABI to the audit tools
in userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The ARM audit code incorrectly uses the saved application ip register
value to infer syscall entry or exit. Additionally, the saved value will
be clobbered if the current task is not being traced, which can lead to
libc corruption if ip is live (apparently glibc uses it for the TLS
pointer).
This patch fixes the syscall tracing code so that the why parameter is
used to infer the syscall direction and the saved ip is only updated if
we know that we will be signalling a ptrace trap.
Reported-and-Tested-by: Jon Masters <jcm@jonmasters.org>
Cc: stable@vger.kernel.org
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The inline assembly in kernel_execve() uses r8 and r9. Since this
code sequence does not return, it usually doesn't matter if the
register clobber list is accurate. However, I saw a case where a
particular version of gcc used r8 as an intermediate for the value
eventually passed to r9. Because r8 is used in the inline
assembly, and not mentioned in the clobber list, r9 was set
to an incorrect value.
This resulted in a kernel panic on execution of the first user-space
program in the system. r9 is used in ret_to_user as the thread_info
pointer, and if it's wrong, bad things happen.
Cc: <stable@vger.kernel.org>
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 46f8c3c7e95c0d30d95911e7975ddc4f93b3e237.
The commit above swapped the DSI1_PPID and DSI2_PPID register fields in
CONTROL_DSIPHY to be in sync with the newer public OMAP TRMs(after version V).
With this commit, contention errors were reported on DSI lanes some OMAP4 SDPs.
After probing the DSI lanes on OMAP4 SDP, it was seen that setting bits in the
DSI2_PPID field was pulling up voltage on DSI1 lanes, and DSI1_PPID field was
pulling up voltage on DSI2 lanes.
This proves that the current version of OMAP4 TRM is incorrect, swap the
position of register fields according to the older TRM versions as they were
correct.
Cc: stable@vger.kernel.org # v3.2+
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 384ebe1c2849160d040df3e68634ec506f13d9ff, "gpio/omap: Add DT
support to GPIO driver", introduced dynamic IRQ numbering of OMAP GPIO
interrupts, breaking all IH_GPIO_BASE based IRQ number calculations.
This issue was corrected in the OMAP GPIO driver and the related header
file with commit 25db711df3258d125dc1209800317e5c0ef3c870, "gpio/omap:
Fix IRQ handling for SPARSE_IRQ".
However, the Amstrad Delta FIQ handler, which replaces the gpio-omap
driver in serving GPIO interrupts on this board, still uses that
outdated method. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7406/1: hotplug: copy the affinity mask when forcefully migrating IRQs
ARM: 7405/1: kexec: call platform_cpu_kill on the killer rather than the victim
ARM: 7403/1: tls: remove covert channel via TPIDRURW
ARM: 7401/1: mm: Fix section mismatches
ARM: OMAP: fix DMA vs memory ordering
ARM: 7390/1: dts: versatile-pb/ab fix MMC IRQs
ARM: 7400/1: vfp: clear fpscr length and stride bits on entry to sig handler
ARM: 7399/1: vfp: move user vfp state save/restore code out of signal.c
ARM: 7398/1: l2x0: only write to debug registers on PL310
ARM: 7397/1: l2x0: only apply workaround for erratum #753970 on PL310
ARM: 7396/1: errata: only handle ARM erratum #326103 on affected cores
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors
and warnings mostly, but also some clock/device setup issues on
exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: msm: Fix gic irqdomain support
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
|
|
When a CPU is hotplugged off, we migrate any IRQs currently affine to it
away and onto another online CPU by calling the irq_set_affinity
function of the relevant interrupt controller chip. This function
returns either IRQ_SET_MASK_OK or IRQ_SET_MASK_OK_NOCOPY, to indicate
whether irq_data.affinity was updated.
If we are forcefully migrating an interrupt (because the affinity mask
no longer identifies any online CPUs) then we should update the IRQ
affinity mask to reflect the new CPU set. Failure to do so can
potentially leave /proc/irq/n/smp_affinity identifying only offline
CPUs, which may confuse userspace IRQ balancing daemons.
This patch updates migrate_one_irq to copy the affinity mask when
the interrupt chip returns IRQ_SET_MASK_OK after forcefully changing the
affinity of an interrupt.
Cc: stable@vger.kernel.org
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When performing a kexec on an SMP system, the secondary cores are stopped
by calling machine_shutdown(), which in turn issues IPIs to offline the
other CPUs. Unfortunately, this isn't enough to reboot the cores into
a new kernel (since they are just executing a cpu_relax loop somewhere
in memory) so we make use of platform_cpu_kill, part of the CPU hotplug
implementation, to place the cores somewhere safe. This function expects
to be called on the killing CPU for each core that it takes out.
This patch moves the platform_cpu_kill callback out of the IPI handler
and into smp_send_stop, therefore ensuring that it executes on the
killing CPU rather than on the victim, matching what the hotplug code
requires.
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
TPIDRURW is a user read/write register forming part of the group of
thread registers in more recent versions of the ARM architecture (~v6+).
Currently, the kernel does not touch this register, which allows tasks
to communicate covertly by reading and writing to the register without
context-switching affecting its contents.
This patch clears TPIDRURW when TPIDRURO is updated via the set_tls
macro, which is called directly from __switch_to. Since the current
behaviour makes the register useless to userspace as far as thread
pointers are concerned, simply clearing the register (rather than saving
and restoring it) will not cause any problems to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: vmlinux.o(.text+0x111b8): Section mismatch in reference
from the function arm_memory_present() to the function
.init.text:memory_present()
The function arm_memory_present() references
the function __init memory_present().
This is often because arm_memory_present lacks a __init
annotation or the annotation of memory_present is wrong.
WARNING: arch/arm/mm/built-in.o(.text+0x1edc): Section mismatch
in reference from the function alloc_init_pud() to the function
.init.text:alloc_init_section()
The function alloc_init_pud() references
the function __init alloc_init_section().
This is often because alloc_init_pud lacks a __init
annotation or the annotation of alloc_init_section is wrong.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
|
|
* 'fixes' of git://github.com/hzhuang1/linux:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
|
|
Pins configured as input and have MFP_LPM_DRIVE_* flag set, can have a
wrong output value for some period of time (spike) during the suspend
sequence.
This can happen because the direction of the pins (GPDR) is set by
software and the output level is set by hardware (PGSR) at a later
stage.
Fix the above potential bug by setting the output levels first.
Also save the actual levels of the pins before the suspend and restore
them after the resume, but before the direction settings take place, so
the same bug as described above will not happen in the resume sequence.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output
must retain the output state in low power mode.
Currently, the pin direction configuration is overrided with values
in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting.
Fix the above bug and add some documentation to clarify the
MFP_LPM_KEEP_OUTPUT setting purpose.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
DEFINE_RES_MEM() takes the size of resource as a second argument,
not the end address. Passing end address leads to following error
in runtime during device registration:
sa1100-rtc: failed to claim resource 0
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
Merge fixes from Andrew Morton:
"13 fixes. The acerhdf patches aren't (really) fixes. But they've
been stuck in my tree for up to two years, sent to Matthew multiple
times and the developers are unhappy."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (13 patches)
mm: fix NULL ptr dereference in move_pages
mm: fix NULL ptr dereference in migrate_pages
revert "proc: clear_refs: do not clear reserved pages"
drivers/rtc/rtc-ds1307.c: fix BUG shown with lock debugging enabled
arch/arm/mach-ux500/mbox-db5500.c: world-writable sysfs fifo file
hugetlbfs: lockdep annotate root inode properly
acerhdf: lowered default temp fanon/fanoff values
acerhdf: add support for new hardware
acerhdf: add support for Aspire 1410 BIOS v1.3314
fs/buffer.c: remove BUG() in possible but rare condition
mm: fix up the vmscan stat in vmstat
epoll: clear the tfile_check_list on -ELOOP
mm/hugetlb: fix warning in alloc_huge_page/dequeue_huge_page_vma
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
* 'u300-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
|
|
Don't allow everybody to use a modem.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
* 'msm-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Fix gic irqdomain support
|
|
Commit 6e8201f57c935 "mmc: core: add the capability for broken voltage"
introduced a new quirk to indicate that MMC core should ignore voltage
change errors reported by the regulators core. This is required to get
SDHCI working on UniversalC210, NURI and GONI boards again after commit
ceb6143b2df81c ("mmc: sdhci: fix vmmc handling").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
