| Age | Commit message (Collapse) | Author |
|---|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
davinci: cpufreq: fix section mismatch warning
DaVinci: fix compilation warnings in <mach/clkdev.h>
davinci: tnetv107x: fix register indexing for GPIOs numbers > 31
davinci: da8xx/omap-l1x: add platform device for davinci-pcm-audio
ARM: pxa/tosa: register wm9712 codec device
ARM: pxa: enable pxa-pcm-audio on pxa210/pxa25x platform
ARM: pxa/colibri: don't register pxa2xx-pcmcia nodes on non-colibri platforms
ARM: pxa/tosa: drop setting LED trigger name, as it's unsupported now
ARM: 6762/1: Update number of VIC for S5P6442 and S5PC100
ARM: 6761/1: Update number of VIC for S5PV210
ARM: 6768/1: hw_breakpoint: ensure debug logic is powered up on v7 cores
ARM: 6767/1: ptrace: fix register indexing in GETHBPREGS request
ARM: 6765/1: remove obsolete comment from asm/mach/arch.h
ARM: 6757/1: fix tlb.h induced linux/swap.h build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: mailbox: resolve hang issue
OMAP2+: PM: SmartReflex: fix memory leaks in Smartreflex driver
arm: mach-omap2: smartreflex: fix another memory leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: mackerel: modify LCDC clock divider value
ARM: mach-shmobile: ap4evb: modify LCDC clock divider value
ARM: mach-shmobile: mackerel: fixup memory initialize for zboot
ARM: mach-shmobile: ap4evb: fixup memory initialize for zboot
ARM: mach-shmobile: Add sh73a0 MIPI-CSI and CEU clocks
ARM: mach-shmobile: AG5EVM MIPI-DSI LCD reset delay fix
|
|
The debugfs support added to the regulator API (which has been merged
in during this merge window) creates directories for regulators named
after the display names for the regulators so replace / as a separator
for multiple supplies with + in the SMDK6410 machine.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Avoid relying on implicit inclusion of machine.h
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Reduce the logging output of s3c64xx_dma_init1() as it is not useful
for normal bootup (and we get an overall indication of the registration
of the PL180 DMA block).
This removes the following output from the log:
s3c64xx_dma_init1: registering DMA 0 (e0808100)
s3c64xx_dma_init1: registering DMA 1 (e0808120)
s3c64xx_dma_init1: registering DMA 2 (e0808140)
s3c64xx_dma_init1: registering DMA 3 (e0808160)
s3c64xx_dma_init1: registering DMA 4 (e0808180)
s3c64xx_dma_init1: registering DMA 5 (e08081a0)
s3c64xx_dma_init1: registering DMA 6 (e08081c0)
s3c64xx_dma_init1: registering DMA 7 (e08081e0)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The MMC core calls s3c6400_setup_sdhcp_cfg_card() very frequently, causing
the log message in there at KERN_INFO to be displayed a lot which is slow
and overly chatty. Convert the message into a pr_debug() to tone this down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The clock for i2c1 has been missing for a while, add it to the list of
clocks for the system and ensure it is initialised at startup.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
No need to put these in the global namespace and sparse gets upset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Ensures that the declaration agrees with the definition and makes sparse
happy.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The call to s3c_gpio_cfgrange_nopull() takes a size and base
but this looks like it is trying to do base and end. This means
it is configuring too many GPIOs and on the case of the Cragganmore
means we're seeing an overflow of the ROW pins causing problems
with the keyboard driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The gta02 header file still uses the old S3C2410_GPJx defines instead of the
S3C2410_GPJ(x) macro. Since the S3C2410_GPJx defines have already been removed
this causes the following build failure:
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_set_spk':
sound/soc/samsung/neo1973_wm8753.c:259: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c:259: error: (Each undeclared identifier is reported only once
sound/soc/samsung/neo1973_wm8753.c:259: error: for each function it appears in.)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_get_spk':
sound/soc/samsung/neo1973_wm8753.c:267: error: 'S3C2440_GPJ2' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: In function 'lm4853_event':
sound/soc/samsung/neo1973_wm8753.c:276: error: 'S3C2440_GPJ1' undeclared (first use in this function)
sound/soc/samsung/neo1973_wm8753.c: At top level:
sound/soc/samsung/neo1973_wm8753.c:439: error: 'S3C2440_GPJ2' undeclared here (not in a function)
sound/soc/samsung/neo1973_wm8753.c:440: error: 'S3C2440_GPJ1' undeclared here (not in a function)
This patches fixes the issue by doing a s,S3C2410_GPJ([\d]+),S3C2410_GPJ(\1),g
on the file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch modifies the number of total GPIO lines for Bank F
for Samsung S5P6440 and S5P6450 SoCs from 2 to 16.
This is necessary as the GPIO lines from 0 to 13 are reserved
and only lines 14 and 15 are used. As during initialization,
the line number starts at 0, putting 2 does not solve the
intended purpose.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The gta02 mach file references the ohci device.
So we need to select S3C_DEV_USB_HOST to have the device available.
This fixes the following linker errors:
arch/arm/mach-s3c2440/built-in.o: In function 'gta02_machine_init':
mach-gta02.c:(.init.text+0x370): undefined reference to 's3c_ohci_set_platdata'
arch/arm/mach-s3c2440/built-in.o:(.init.data+0xac): undefined reference to 's3c_device_ohci'
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
mackerel WVGA LCDC panel expect 33.3MHz for dot-clock,
but current dot-clock was 50.0MHz.
This patch modify clock divider value.
Signed-off-by: Makoto Ueda <makoto.ueda.ub@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
ap4evb WVGA LCDC panel expect 33.3MHz for dot-clock,
but current dot-clock was 50.0MHz.
This patch modify clock divider value.
Signed-off-by: Makoto Ueda <makoto.ueda.ub@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-fixes
|
|
omap4 interrupt disable bits is different. On rx kfifo full, the mbox rx
interrupts wasn't getting disabled, and this is causing the rcm stress tests
to hang.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Armando Uribe <x0095078@ti.com>
Signed-off-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This Patch frees all the dynamically allocated memory
which couldn't have been released in some error hitting cases.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Temporary strings with volt_* file names should be released after the
debugfs entries are created. While at it, also simplify the string
allocation, and use just snprintf() to create the name.
The patch eliminates kmemleak reports with the following stack trace
(multiple objects depending on HW):
unreferenced object 0xcedbc5a0 (size 64):
comm "swapper", pid 1, jiffies 4294929375 (age 423.734s)
hex dump (first 32 bytes):
76 6f 6c 74 5f 39 37 35 30 30 30 00 00 00 00 00 volt_975000.....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<c012fee0>] create_object+0x104/0x208
[<c012dbc8>] kmem_cache_alloc_trace+0xf0/0x17c
[<c0013f64>] omap_sr_probe+0x314/0x420
[<c02a1724>] platform_drv_probe+0x18/0x1c
[<c02a088c>] driver_probe_device+0xc8/0x188
[<c02a09b4>] __driver_attach+0x68/0x8c
[<c02a00ac>] bus_for_each_dev+0x44/0x74
[<c029f9e0>] bus_add_driver+0xa0/0x228
[<c02a0cac>] driver_register+0xa8/0x130
[<c02a1b2c>] platform_driver_probe+0x18/0x8c
[<c0013c1c>] sr_init+0x40/0x74
[<c005a554>] do_one_initcall+0xc8/0x1a0
[<c00084f4>] kernel_init+0x150/0x218
[<c0065d64>] kernel_thread_exit+0x0/0x8
[<ffffffff>] 0xffffffff
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap4: prcm: Fix the CPUx clockdomain offsets
OMAP2+: clocksource: fix crash on boot when !CONFIG_OMAP_32K_TIMER
OMAP2/3: clock: fix fint calculation for DPLL_FREQSEL
OMAP2+: mailbox: fix lookups for multiple mailboxes
OMAP2420: mailbox: fix IVA vs DSP IRQ numbering
mach-omap2: smartreflex: world-writable debugfs voltage files
mach-omap2: pm: world-writable debugfs timer files
mach-omap2: mux: world-writable debugfs files
|
|
Fix below section mismatch warning:
WARNING: vmlinux.o(.data+0x673c): Section mismatch in reference from the variable davinci_driver to the function .init.text:davinci_cpu_init()
The variable davinci_driver references
the function __init davinci_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Commit 6d803ba736abb5e122dede70a4720e4843dd6df4 (ARM: 6483/1: arm & sh:
factorised duplicated clkdev.c) caused the following warnings:
In file included from /home/headless/src/kernel.org/linux-davinci/arch/arm/
include/asm/clkdev.h:17,
from include/linux/clkdev.h:15,
from arch/arm/mach-davinci/clock.h:71,
from arch/arm/mach-davinci/common.c:22:
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: `struct clk' declared
inside parameter list
arch/arm/mach-davinci/include/mach/clkdev.h:4: warning: its scope is only this
definition or declaration, which is probably not what you want
arch/arm/mach-davinci/include/mach/clkdev.h:9: warning: `struct clk' declared
inside parameter list
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This patch fix a bug in the register indexing for GPIOs numbers > 31
to get the relevant hardware registers of tnetv107x to control the GPIOs.
In the structure tnetv107x_gpio_regs:
struct tnetv107x_gpio_regs {
u32 idver;
u32 data_in[3];
u32 data_out[3];
u32 direction[3];
u32 enable[3];
};
The GPIO hardware register addresses of tnetv107x are stored.
The chip implements 3 registers of each entity to serve 96 GPIOs,
each register provides a subset of 32 GPIOs.
The driver provides these macros: gpio_reg_set_bit, gpio_reg_get_bit
and gpio_reg_clear_bit.
The bug implied the use of macros to access the relevant hardware
register e.g. the driver code used the macro like this:
'gpio_reg_clear_bit(®->data_out, gpio)'
But it has to be used like this:
'gpio_reg_clear_bit(reg->data_out, gpio)'.
The different results are shown here:
- ®->data_out + 1 (it will add the full array size of data_out i.e. 12 bytes)
- reg->data_out + 1 (it will increment only the size of data_out i.e. only 4 bytes)
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Hirosh Dabui <hirosh.dabui@snom.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
After the multi-component commit f0fba2ad (ASoC: multi-component - ASoC
Multi-Component Support) for ASoC, we need to register the platform
device for davinci-pcm-audio.
This patch and patch at [1] are required for audio to work on
DA850/OMAP-L138.
[1] https://patchwork.kernel.org/patch/495211/
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
Since f0fba2ad1b it's required to register platform devices even for
AC'97 codecs. Register one on tosa (wm9712-codec).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
pxa25x platforms were left out of major ASoC Update patch.
Since f0fba2ad1b a registration of pxa-pcm-audio device is required for
ASoC to function on pxa platforms. Register one also for pxa210/pxa25x.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Since 2e48928d8a0f38c1b5c81eb3f1294de8a6382c68 it's no longer possible to set
the name of the LED trigger for RFKILL events. Drop respective code from tosa-bt.c
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The S5P6442 and S5PC100 SoCs have 4 VICs. However, default VIC number
is defined 2 in arch/arm/common. So can be happened some problem on it.
Basically, it requires for suspend and resume.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The S5PV210 SoC have 4 VICs. It requires for suspend and resume.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ARMv7 allows the debug core logic to be powered down and provides the
DBGPRSR register so that software can power-up and check the status of
the logic.
This patch ensures that the debug logic is powered up on ARMv7 cores
before we attempt to access the extended debug registers.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The GETHBPREGS ptrace request incorrectly maps its index argument onto
the thread's saved debug state when the index != 0. This has not yet
been seen from userspace because GDB (the only user of this request)
only reads from register 0.
This patch fixes the indexing.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since commit 6fc31d54 this comment is no longer true.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
devel-fixes
|
|
CPU0 and CPU1 clockdomain is at the offset of 0x18 from the LPRM base.
The header file has set it wrongly to 0x0. Offset 0x0 is for CPUx power
domain control register
Fix the same.
The autogen scripts is fixed thanks to Benoit Cousson
With the old value, the clockdomain code would access the
*_PWRSTCTRL.POWERSTATE field when it thought it was accessing the
*_CLKSTCTRL.CLKTRCTRL field. In the worst case, this could cause
system power management to behave incorrectly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
OMAP2+ kernels built without CONFIG_OMAP_32K_TIMER crash on boot after the
2.6.38 sched_clock changes:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 13000000 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (2.6.38-rc5-00057-g04aa67d #152)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
Without CONFIG_OMAP_32K_TIMER, the kernel has an clockevent and
clocksource resolution about three orders of magnitude higher than
with CONFIG_OMAP_32K_TIMER set. The tradeoff is that the lowest
power consumption states are not available.
Fix by calling init_sched_clock() from the GPTIMER clocksource init code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: serio/gameport - use 'long' system workqueue
Input: synaptics - document 0x0c query
Input: tegra-kbc - add function keymap
|
|
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit
06824ba (ARM: tlb: delay page freeing for SMP and ARMv7 CPUs)
introduced a build failure for builds with CONFIG_SWAP=n:
In file included from arch/arm/mm/init.c:27:
arch/arm/include/asm/tlb.h: In function 'tlb_flush_mmu':
arch/arm/include/asm/tlb.h:101: error: implicit declaration of function 'release_pages'
arch/arm/include/asm/tlb.h: In function 'tlb_remove_page':
arch/arm/include/asm/tlb.h:165: error: implicit declaration of function 'page_cache_release'
as linux/swap.h doesn't include linux/pagemap.h but actually needs it
(see comments in linux/swap.h as to why this is.)
Fix that by #including <linux/pagemap.h> in <asm/pgalloc.h> as it's done
by x86.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In OMAP35X TRM Rev 2010-05 Figure 7-18 "DPLL With EMI Reduction
Feature", it is shown that the internal frequency is calculated by
CLK_IN/(N+1). However, the value passed to _dpll_test_fint() is
already "N+1" since Linux is using the values to divide by. In the
technical reference manual, "N" is referring to the divider's register
value (0-127).
During power management testing, it was observed that programming the
wrong jitter correction value can cause the system to become unstable
and eventually crash.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
[paul@pwsan.com: added second paragraph to commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV210: Fix regulator names
ARM: S5PV210: Update max8998_platform_data
ARM: SAMSUNG: Drop exporting s3c24xx_ts_set_platdata
ARM: S5P: Fix end address in memory resource information for UART devices
ARM: S5P64X0: Cleanup map.h file
ARM: S5P6442: Cleanup map.h file
ARM: S5PC100: Clenaup map.h file
ARM: S5PV210: Cleanup map.h file
ARM: S5PV310: Cleanup map.h file
|
|
Marcin Slusarz says:
> In arch/arm/kernel/kprobes-decode.c there's a function
> arm_kprobe_decode_insn which does:
>
> } else if ((insn & 0x0e000000) == 0x0c400000) {
> ...
>
> This is always false, so code below is dead.
> I found this bug by coccinelle (http://coccinelle.lip6.fr/).
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's no need to noMMU to put tlb_flush() in asm/tlbflush.h - it's
part of the tlb shootdown interface. Move it to asm/tlb.h instead, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We need to delay freeing any mapped page on SMP and ARMv7 systems to
ensure that the data is not accessed by other CPUs, or is used for
speculative prefetch with ARMv7. This includes not only mapped pages
but also pages used for the page tables themselves.
This avoids races with the MMU/other CPUs accessing pages after they've
been freed but before we've invalidated the TLB.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When SMP_ON_UP is used and the spinlocks are inlined, we end up with
inline spinlocks in the exit code, with references from the SMP
alternatives section to the exit sections. This causes link time
errors. Avoid this by placing the exit sections in the init-discarded
region.
Cc: <stable@kernel.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Cc: <stable@kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
