summaryrefslogtreecommitdiffstats
path: root/arch/arm
AgeCommit message (Collapse)Author
2012-05-15ARM: PRIMA2: add prima2_defconfig for CSR SiRFprimaIIBarry Song
Signed-off-by: Barry Song <Baohua.Song@csr.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'marvell_cleanup_for_v3.5' of ↵Arnd Bergmann
git://git.infradead.org/users/jcooper/linux into next/cleanup * 'marvell_cleanup_for_v3.5' of git://git.infradead.org/users/jcooper/linux: Dove: Fix Section mismatch warnings ARM: orion5x: ts78xx debugging changes ARM: orion5x: remove PM dependency from ts78xx ARM: orion5x: ts78xx fix NAND resource off by one ARM: orion5x: ts78xx whitespace cleanups Orion5x: Fix Section mismatch warnings Orion5x: Fix warning: struct pci_dev declared inside paramter list Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'next/devel-samsung' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc2 * 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: EXYNOS: Support Suspend/Resume for EXYNOS4412 ARM: EXYNOS: To use common config for EXYNOS4 and EXYNOS5 SPI ARM: EXYNOS: Support DMA for EXYNOS5250 SoC ARM: EXYNOS: Add platform resource definitions for FIMC-LITE ARM: EXYNOS: add platform device for core DRM subsystem ARM: EXYNOS: add dts files to dtbs target spi/s3c64xx: Allow usage for ARCH_S3C24XX ARM: S3C24XX: Add HSSPI setup callback for s3c64xx-spi driver ARM: S3C24XX: Add clock-lookup entries required by s3c64xx-spi ARM: S3C24XX: Add map entries needed by the s3c64xx-spi devices ARM: S3C24XX: claim spi channels for hsspi in dma-s3c2443 ARM: S3C24XX: Add forgotten clock lookup table to S3C2443 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'exynos/iommu' into next/soc2Arnd Bergmann
This is a dependency for the following samsung changes. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15ARM: nomadik: enable PINCTRL_NOMADIK where neededArnd Bergmann
The nomadik gpio code has been converted to pinctrl, but the nomadik platform still expects the old code to be present. Change it to use the new one instead. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2012-05-15[media] media: mx2_camera: Fix mbus format handlingJavier Martin
Remove MX2_CAMERA_SWAP16 and MX2_CAMERA_PACK_DIR_MSB flags so that the driver can negotiate with the attached sensor whether the mbus format needs convertion from UYUV to YUYV or not. Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-15[media] i.MX27: visstrim_m10: Remove use of MX2_CAMERA_SWAP16Javier Martin
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2012-05-15Merge branch 'drivers/mmc' into next/dt2Arnd Bergmann
Changes in the dt2 branch move stuff around that gets changed in the drivers/mmc branch. I chose a non-obvious resolution by adding the new bus-width property into all the tegra sdhci device nodes. Conflicts: arch/arm/boot/dts/tegra-cardhu.dts arch/arm/boot/dts/tegra-harmony.dts arch/arm/boot/dts/tegra-ventana.dts Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'drivers/mmc' into next/driversArnd Bergmann
* drivers/mmc: mmc: dt: Consolidate DT bindings Also pulls in the omap/dt-missed-3.4 branch as a dependency. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'for-3.5/ahb' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers * tegra/ahb: ARM: tegra: Add SMMU enabler in AHB ARM: tegra: Add Tegra AHB driver Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15mmc: dt: Consolidate DT bindingsArnd Bergmann
This patch unifies the current DT MMC bindings documentation and code, adds generic MMC DT bindings documentation, and updates .dts files for consistency. [cjb: typo fixes, addition of max-frequency property] Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'kirkwood_boards_for_v3.5' of ↵Arnd Bergmann
git://git.infradead.org/users/jcooper/linux into next/boards * 'kirkwood_boards_for_v3.5' of git://git.infradead.org/users/jcooper/linux: ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree kirkwood: Add iconnect support orion/kirkwood: create a generic function for gpio led blinking kirkwood/orion: fix orion_gpio_set_blink ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt kirkwood: Allow nand to be configured via. devicetree mtd: Add orion_nand devicetree bindings ARM: kirkwood: Basic support for DNS-320 and DNS-325 Includes an update to v3.4-rc7 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15Merge branch 'board-new' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into next/boards "Rafael J. Wysocki" <rjw@sisk.pl> writes: Renesas ARM-based platforms: new boards support for v3.5 * Support for the KZM-A9-GT board from Kuninori Morimoto and Magnus Damm. * Support for the armadillo800eva board from Kuninori Morimoto and Magnus Damm. This is based on the Renesas core SoC code updates I've sent a separate pull request for. * 'board-new' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas: (29 commits) ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva ARM: mach-shmobile: Use DT_MACHINE for KZM9G ARM: mach-shmobile: kzm9g: enable SMP boot ARM: mach-shmobile: kzm9g: defconfig update ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key ARM: mach-shmobile: kzm9g: add SDHI support ARM: mach-shmobile: kzm9g: add MMCIF support ARM: mach-shmobile: kzm9g: correct screen direction ARM: mach-shmobile: sh73a0.h: add GPIO_NR ARM: mach-shmobile: pfc-sh73a0: fixup MSEL2CR MSEL18 for I2C-3 ARM: mach-shmobile: kzm9g: add ST1232 Touchscreen support ARM: mach-shmobile: kzm9g: add LCDC support ARM: mach-shmobile: kzm9g: add external USB Host support ARM: mach-shmobile: kzm9g: add SMSC 9221 support ARM: mach-shmobile: kzm9g: add defconfig ARM: mach-shmobile: add KZM-A9-GT board support ARM: mach-shmobile: armadillo800eva: defconfig update ARM: mach-shmobile: clock-r8a7740: add sh-eth clock ARM: mach-shmobile: r8a7740: reserve DMA memory for the frame buffer ARM: mach-shmobile: armadillo800eva: add MMCIF support ... Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-15ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definitionChanghwan Youn
Redefine IRQ_MCT_L0,1 irq definition as it is changed in rev1 of EXYNOS5. Signed-off-by: Changhwan Youn <chaos.youn@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-05-15ARM: EXYNOS: Modify the GIC physical address for static io-mappingChanghwan Youn
Adapt to changes in GIC physical address in rev1 of EXYNOS5. Signed-off-by: Changhwan Youn <chaos.youn@samsung.com> Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-05-15ARM: EXYNOS: Add watchdog timer clock instanceThomas Abraham
Add watchdog timer clock instance for EXYNOS5 watchdog controller. Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2012-05-15mach-ux500: crypto - core support for CRYP/HASH module.Andreas Westin
This adds the required platform data and calls to enable the CRYP/HASH driver. Signed-off-by: Andreas Westin <andreas.westin@stericsson.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2012-05-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linuxHerbert Xu
Merge mainline to add prerequisite for ARM ux500 crypto support.
2012-05-15Merge branch 'next/cleanup-plat-s5p' into next/devel-exynos5250-1Kukjin Kim
2012-05-15ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetreeSimon Baatz
Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as currently possible in the devicetree files, including the NAND partitions. Use the partition scheme of the original firmware by default. Create a board-ib62x0.c for everything else. Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15dmaengine: at_hdmac: take maxburst from slave configurationNicolas Ferre
The maxburst/chunk size was taken from the private slave DMA data structure. Use the common API provided by DMA_SLAVE_CONFIG to setup src/dst maxburst values. The ctrla field is not needed anymore in the slave private structure nor the header constants that were located in an architecture specific directory. The at91sam9g45_devices.c file that was using this platform data is also modified to remove this now useless data. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-05-15dmaengine: at_hdmac: remove some at_dma_slave commentsNicolas Ferre
These comments were covering removed struct at_dma_slave fields. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-05-15kirkwood: Add iconnect supportArnaud Patard (Rtp)
Add support for Iomega Iconnect system. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-By: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15orion/kirkwood: create a generic function for gpio led blinkingArnaud Patard (Rtp)
dns323 and (at least) iconnect platforms are using hw led blinking, so, instead of having 2 identicals .gpio_blink_set gpio-led hooks, move dns323 code into gpio.c Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-By: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15kirkwood/orion: fix orion_gpio_set_blinkArnaud Patard (Rtp)
gpio registers are for 32 gpios. Given that orion_gpio_set_blink is called directly and not through gpiolib, it needs to make sure that the pin value given to the internal functions are between 0 and 31. Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Tested-By: Adam Baker <linux@baker-net.org.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdtJamie Lentin
Use devicetree to define NAND partitions. Use D-link partition scheme by default, to be vaguely compatible with their userland. Changes since last submission (V4):- * Don't add NAND support then throw it away immediately after [Grant Likely] Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15kirkwood: Allow nand to be configured via. devicetreeJamie Lentin
Add default configuration for NAND, to be enabled in your board config. Ensure clock gating is set appropriately when the NAND is enabled. Acked-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-15ARM: kirkwood: Basic support for DNS-320 and DNS-325Jamie Lentin
Add support for the DNS-320 and DNS-325. Describe as much as currently possible in the devicetree files, create a board-dnskw.c for everything else. Changes since last submission (V3) [Addressing comments by]:- * One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper] * Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely] * Don't add NAND support then throw it away immediately after [Grant Likely] * Describe purpose of MPP 41, 42 & 49 Changes since last submission (V2):- * Use IEEE-compliant "okay", rather than "ok" [Scott Wood] Signed-off-by: Jamie Lentin <jm@lentin.co.uk> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-05-14Merge branch 'renesas-kzm9g' into renesas-board-newRafael J. Wysocki
* renesas-kzm9g: ARM: mach-shmobile: Use DT_MACHINE for KZM9G
2012-05-14Merge branch 'renesas-armadillo800eva' into renesas-board-newRafael J. Wysocki
* renesas-armadillo800eva: ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
2012-05-14ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 evaMagnus Damm
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board. Also include a tiny DTS file to describe the board and update the Kconfig dependencies to select CONFIG_USE_OF. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-05-14ARM: mach-shmobile: Use DT_MACHINE for KZM9GMagnus Damm
Use DT_MACHINE_START() on the sh73a0 based KZM9G board. Also include a tiny DTS file to describe the board and update the Kconfig dependencies to select CONFIG_USE_OF. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2012-05-14ARM: AT91: Add ADC driver to the at91sam9g20 dtsiMaxime Ripard
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14ARM: AT91: Add ADC driver to the at91sam9x5 dtsiMaxime Ripard
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14ARM: AT91: Add ADC driver to the at91sam9g45 dtsiMaxime Ripard
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14ARM: AT91: Add the ADC clock to the sam9x5 SoC fileMaxime Ripard
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14ARM: AT91: ADC: Add support for the AT91SAM9M10G45-EK boardMaxime Ripard
This patch adds platform data for the AT91 ADC driver support for the AT91SAM9M10G45-EK board. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14ARM: AT91: Add the ADC to the sam9g20ek boardMaxime Ripard
This patch adds platform data for the AT91 ADC driver support for the AT91SAM9G20-EK board. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-14Merge branch 'for-3.5/dt2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into for-next Stephen Warren <swarren@wwwdotorg.org> writes: This branch is based on the merge of the following branches from the Tegra repo, which are all already pulled into arm-soc: for-3.5/tegra30-audio for-3.5/usb-ulpi for-3.5/dt ... which are all based on for-3.5/gpio-pinmux * 'for-3.5/dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: ARM: dt: tegra: invert status=disable vs status=okay ARM: dt: tegra: consistent basic property ordering ARM: dt: tegra: sort nodes based on bus order ARM: dt: tegra: remove duplicate device_type property ARM: dt: tegra: consistenly use lower-case for hex constants ARM: dt: tegra: format regs properties consistently ARM: dt: tegra: gpio comment cleanup ARM: dt: tegra: remove unnecessary unit addresses ARM: dt: tegra: whitespace cleanup ARM: dt: tegra cardhu: fix typo in SDHCI node name ARM: dt: tegra: cardhu: register core regulator tps62361 ARM: dt: tegra30.dtsi: Add SMMU node ARM: dt: tegra20.dtsi: Add GART node ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes ARM: dt: tegra: Add device tree support for AHB Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'next/board-samsung' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/boards Kukjin Kim <kgene.kim@samsung.com> writes: As there were discussions, some exynos4 boards have been updated because current dt cannot support all features for current board files on exynos4. Note, this should be merged after next/devel-samsung because some platform devices are defined in that. * 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: EXYNOS: Add FIMC device to SMDK4X12 ARM: EXYNOS: Add MFC device to SMDK4X12 ARM: EXYNOS: Add DRM device to SMDKV310 ARM: EXYNOS: Add DRM device to Origen ARM: EXYNOS: Make BT platform data structure static in mach-origen.c file ARM: EXYNOS: Add DRM core support for NURI board ARM: EXYNOS: Add DRM core device support for Universal C210 board ARM: EXYNOS: Increase framebuffer virtual size for origen ARM: S3C64XX: Hook up new style regulator-regulator supplies on Cragganmore Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'next/cpuidle' into next/pmArnd Bergmann
No point maintaining two branches for power management Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'omap/dt-missed-3.4' into drivers/mmcArnd Bergmann
The omap/dt branch adds a few instances of mmc device nodes that need to get changed to use the common bindings. Pull that into a new branch so we can apply the patch in a single run. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'power' of git://github.com/hzhuang1/linux into next/pmArnd Bergmann
* 'power' of git://github.com/hzhuang1/linux: ARM: mmp: add pm support for pxa910 ARM: mmp: ttc_dkb: add PMIC support ARM: cache: tauros2: add disable and resume callback ARM: mm: proc-mohawk: add suspend resume for mohawk ARM: mmp: add PM support for mmp2 ARM: mmp: move XX_REG definition to addr-map.h Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'mmp/dt' into next/pmArnd Bergmann
The mmp power management changes are based on this branch, so pull it in as a dependency. Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'dt' of git://github.com/hzhuang1/linux into next/dtArnd Bergmann
* 'dt' of git://github.com/hzhuang1/linux: Documentation: update docs for mmp dt ARM: dts: refresh dts file for arch mmp ARM: mmp: support pxa910 with device tree ARM: mmp: support mmp2 with device tree gpio: pxa: parse gpio from DTS file ARM: mmp: support DT in timer ARM: mmp: support DT in irq ARM: mmp: append CONFIG_MACH_MMP2_DT ARM: mmp: fix build issue on mmp with device tree Includes an update to v3-4-rc5 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'next/cleanup-plat-s3c24xx-s5p' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup2 Kukjin Kim <kgene.kim@samsung.com> writes: We can remove plat-s5p directory with this series and I think, the plat-s3c24xx can be removed next time for one plat-samsung of Samsung stuff. Note, this is including cleanup-samsung-iommu which is removing s5p iommu stuff in plat-s5p. * 'next/cleanup-plat-s3c24xx-s5p' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: SAMSUNG: merge plat-s5p into plat-samsung ARM: SAMSUNG: move options for common s5p into plat-samsung/Kconfig ARM: SAMSUNG: move setup code for s5p mfc and mipiphy into plat-samsung ARM: SAMSUNG: move platform device for s5p uart into plat-samsung ARM: SAMSUNG: move hr timer for common s5p into plat-samsung ARM: SAMSUNG: move pm part for common s5p into plat-samsung ARM: SAMSUNG: move interrupt part for common s5p into plat-samsung ARM: SAMSUNG: move clock part for common s5p into plat-samsung ARM: S3C24XX: Use common macro to define resources on dev-uart.c ARM: S3C24XX: move common clock init into common.c ARM: S3C24XX: move common power-management code to mach-s3c24xx ARM: S3C24XX: move plat-s3c24xx/dev-uart.c into common.c ARM: S3C24XX: move plat-s3c24xx/cpu.c Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'exynos/sysmmu' into next/cleanup2Arnd Bergmann
Required as a depdency for the next/cleanup-plat-s3c24xx-s5p branch Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'next/cleanup-samsung-iommu' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers * 'next/cleanup-samsung-iommu' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: EXYNOS: Change System MMU platform device definitions S5P: SYSMMU: Remove System MMU device driver Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-05-14Merge branch 'for-3.5/defconfig2' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/defconfig * 'for-3.5/defconfig2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: ARM: tegra: update defconfig
2012-05-14ARM clps711x: Removed unused header mach/time.hAlexander Shiyan
All functions from this header already provided by common.c Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Arnd Bergmann <arnd@arndb.de>