| Age | Commit message (Collapse) | Author |
|---|
|
into next/soc
* 'features/imx3' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
Conflicts:
arch/arm/mach-imx/mm-imx3.c
|
|
It was observed on a mx31pdk board that audio playback only worked when the bootloader was Redboot, and
did not work when U-boot was used.
Comparing the sources of these bootloaders showed that the AIPS registers were not setup in U-boot.
Instead of relying on the bootloader to setup the AIPS registers, do it in the kernel so that audio
playback can work independantly of the bootloader being used.
Copied the AIPS settings from Redboot to the kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
The LPM field of register CCMR is used to select the mode that the processor will run
when it goes to WFI.
When mx31 enters in WFI mode the LPM field is at its reset value of 0,
which configures the mx31 to enter in "wait mode".
On mx35, the LPM field on mx35 is also at 0 after reset, which corresponds
to "run mode" instead of "wait mode".
Instead of relying on the reset value of LPM to set the low power mode for
WFI, configure mx31 and mx35 to run in "wait mode"
Reported-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: split omap2/3/4_check_revision function
ARM: OMAP2+: Make cpu_rev static global variable
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
* 'imx/defconfig' of git://git.linaro.org/people/shawnguo/linux-2.6: (2 commits)
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
(upadte to v3.3-rc5)
|
|
Some devices on some imx boards are supplied by fixed voltage, so
build REGULATOR_FIXED_VOLTAGE support in.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It adds CONFIG_BLK_DEV_INITRD and runs savedefconfig. The resulted
can boot Linaro rootfs out of box.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
arch/arm/mach-shmobile/board-ag5evm.c: included 'linux/dma-mapping.h'
twice, remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix the bit field width information for the IPSR4 register
in the r8a7779 pin function controller (PFC).
Without this fix the Marzen board fails to receive data
over the serial console due to misconfigured pin function
for the RX pin.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the sh73a0 SMP code to use 32-bit PSTR access.
This fixes wakeup from deep sleep for sh73a0 secondary CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
rmobile-fixes-for-linus
|
|
A few more things this time around. The only thing warranting some
commentry is the modpost change, which allows folk building a Thumb2
enabled kernel to see section mismatch warnings. This is why many
weren't noticed with OMAP.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM/audit: include audit header and fix audit arch
ARM: OMAP: fix voltage domain build errors with PM_OPP disabled
ARM/PCI: Remove ARM's duplicate definition of 'pcibios_max_latency'
ARM: 7336/1: smp_twd: Don't register CPUFREQ notifiers if local timers are not initialised
ARM: 7327/1: need to include asm/system.h in asm/processor.h
ARM: 7326/2: PL330: fix null pointer dereference in pl330_chan_ctrl()
ARM: 7164/3: PL330: Fix the size of the dst_cache_ctrl field
ARM: 7325/1: fix v7 boot with lockdep enabled
ARM: 7324/1: modpost: Fix section warnings for ARM for many compilers
ARM: 7323/1: Do not allow ARM_LPAE on pre-ARMv7 architectures
|
|
Both bugs being fixed were introduced in:
29ef73b7a823b77a7cd0bdd7d7cded3fb6c2587b
Include linux/audit.h to fix below build errors:
CC arch/arm/kernel/ptrace.o
arch/arm/kernel/ptrace.c: In function 'syscall_trace':
arch/arm/kernel/ptrace.c:919: error: implicit declaration of function 'audit_syscall_exit'
arch/arm/kernel/ptrace.c:921: error: implicit declaration of function 'audit_syscall_entry'
arch/arm/kernel/ptrace.c:921: error: 'AUDIT_ARCH_ARMEB' undeclared (first use in this function)
arch/arm/kernel/ptrace.c:921: error: (Each undeclared identifier is reported only once
arch/arm/kernel/ptrace.c:921: error: for each function it appears in.)
make[1]: *** [arch/arm/kernel/ptrace.o] Error 1
make: *** [arch/arm/kernel] Error 2
This part of the patch is:
Reported-by: Axel Lin <axel.lin@gmail.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
(They both provided patches to fix it)
This patch also (at the request of the list) fixes the fact that
ARM has both LE and BE versions however the audit code was called as if
it was always BE. If audit userspace were to try to interpret the bits
it got from a LE system it would obviously do so incorrectly. Fix this
by using the right arch flag on the right system.
This part of the patch is:
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The voltage domain code wants the voltage tables, which are in the
opp*.c files. These files aren't built when PM_OPP is disabled,
causing the following build errors at link time:
twl-common.c:(.init.text+0x2e48): undefined reference to `omap34xx_vddmpu_volt_data'
twl-common.c:(.init.text+0x2e4c): undefined reference to `omap34xx_vddcore_volt_data'
twl-common.c:(.init.text+0x2e5c): undefined reference to `omap36xx_vddmpu_volt_data'
twl-common.c:(.init.text+0x2e60): undefined reference to `omap36xx_vddcore_volt_data'
twl-common.c:(.init.text+0x2830): undefined reference to `omap44xx_vdd_mpu_volt_data'
twl-common.c:(.init.text+0x283c): undefined reference to `omap44xx_vdd_iva_volt_data'
twl-common.c:(.init.text+0x2844): undefined reference to `omap44xx_vdd_core_volt_data'
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The patch series to re-factor PCI's 'latency timer' setup (re:
http://marc.info/?l=linux-kernel&m=131983853831049&w=2) forgot to
remove the ARM specific definition of 'pcibios_max_latency' once such
had been moved into the pci core resulting in ARM related compile
errors -
drivers/built-in.o:(.data+0x230): multiple definition of
`pcibios_max_latency'
arch/arm/common/built-in.o:(.data+0x40c): first defined here
make[1]: *** [vmlinux.o] Error 1
In the series, patch 2/16 (commit 168c8619fd8) converted the ARM
specific version of 'pcibios_set_master()' to a non-inlined version.
This was done in preperation for hosting it up into PCI's core, which
was done in patch 10/16 (commit 96c5590058d) of the series (and
where the removal of ARM's 'pcibios_max_latency' was overlooked).
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
not initialised
Current ARM local timer code registers CPUFREQ notifiers even in case
the twd_timer_setup() isn't called. That seems to be wrong and
would eventually lead to kernel crash on the CPU frequency transitions
on the SOCs where the local timer doesn't exist or broken because of
hardware BUG. Fix it by testing twd_evt and *__this_cpu_ptr(twd_evt).
The issue was observed with v3.3-rc3 and building an OMAP2+ kernel
on OMAP3 SOC which doesn't have TWD.
Below is the dump for reference :
Unable to handle kernel paging request at virtual address 007e900
pgd = cdc20000
[007e9000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP
Modules linked in:
CPU: 0 Not tainted (3.3.0-rc3-pm+debug+initramfs #9)
PC is at twd_update_frequency+0x34/0x48
LR is at twd_update_frequency+0x10/0x48
pc : [<c001382c>] lr : [<c0013808>] psr: 60000093
sp : ce311dd8 ip : 00000000 fp : 00000000
r10: 00000000 r9 : 00000001 r8 : ce310000
r7 : c0440458 r6 : c00137f8 r5 : 00000000 r4 : c0947a74
r3 : 00000000 r2 : 007e9000 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment usr
Control: 10c5387d Table: 8dc20019 DAC: 00000015
Process sh (pid: 599, stack limit = 0xce3102f8)
Stack: (0xce311dd8 to 0xce312000)
1dc0: 6000c
1de0: 00000001 00000002 00000000 00000000 00000000 00000000 00000
1e00: ffffffff c093d8f0 00000000 ce311ebc 00000001 00000001 ce310
1e20: c001386c c0437c4c c0e95b60 c0e95ba8 00000001 c0e95bf8 ffff4
1e40: 00000000 00000000 c005ef74 ce310000 c0435cf0 ce311ebc 00000
1e60: ce352b40 0007a120 c08d5108 c08ba040 c08ba040 c005f030 00000
1e80: c08bc554 c032fe2c 0007a120 c08d4b64 ce352b40 c08d8618 ffff8
1ea0: c08ba040 c033364c ce311ecc c0433b50 00000002 ffffffea c0330
1ec0: 0007a120 0007a120 22222201 00000000 22222222 00000000 ce357
1ee0: ce3d6000 cdc2aed8 ce352ba0 c0470164 00000002 c032f47c 00034
1f00: c0331cac ce352b40 00000007 c032f6d0 ce352bbc 0003d090 c0930
1f20: c093d8bc c03306a4 00000007 ce311f80 00000007 cdc2aec0 ce358
1f40: ce8d20c0 00000007 b6fe5000 ce311f80 00000007 ce310000 0000c
1f60: c000de74 ce987400 ce8d20c0 b6fe5000 00000000 00000000 0000c
1f80: 00000000 00000000 001fbac8 00000000 00000007 001fbac8 00004
1fa0: c000df04 c000dd60 00000007 001fbac8 00000001 b6fe5000 00000
1fc0: 00000007 001fbac8 00000007 00000004 b6fe5000 00000000 00202
1fe0: 00000000 beb565f8 00101ffc 00008e8c 60000010 00000001 00000
[<c001382c>] (twd_update_frequency+0x34/0x48) from [<c008ac4c>] )
[<c008ac4c>] (smp_call_function_single+0x17c/0x1c8) from [<c0013)
[<c0013890>] (twd_cpufreq_transition+0x24/0x30) from [<c0437c4c>)
[<c0437c4c>] (notifier_call_chain+0x44/0x84) from [<c005efe4>] ()
[<c005efe4>] (__srcu_notifier_call_chain+0x70/0xa4) from [<c005f)
[<c005f030>] (srcu_notifier_call_chain+0x18/0x20) from [<c032fe2)
[<c032fe2c>] (cpufreq_notify_transition+0xc8/0x1b0) from [<c0333)
[<c033364c>] (omap_target+0x1b4/0x28c) from [<c032f47c>] (__cpuf)
[<c032f47c>] (__cpufreq_driver_target+0x50/0x64) from [<c0331d24)
[<c0331d24>] (cpufreq_set+0x78/0x98) from [<c032f6d0>] (store_sc)
[<c032f6d0>] (store_scaling_setspeed+0x5c/0x74) from [<c03306a4>)
[<c03306a4>] (store+0x58/0x74) from [<c014d868>] (sysfs_write_fi)
[<c014d868>] (sysfs_write_file+0x80/0xb4) from [<c00f2c2c>] (vfs)
[<c00f2c2c>] (vfs_write+0xa8/0x138) from [<c00f2e9c>] (sys_write)
[<c00f2e9c>] (sys_write+0x40/0x6c) from [<c000dd60>] (ret_fast_s)
Code: e594300c e792210c e1a01000 e5840004 (e7930002)
---[ end trace 5da3b5167c1ecdda ]---
Reported-by: Kevin Hilman <khilman@ti.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
|
|
For files that include asm/processor.h but not asm/system.h:
arch/arm/mach-msm/include/mach/uncompress.h: In function 'putc':
arch/arm/mach-msm/include/mach/uncompress.h:48:3: error: implicit declaration of function 'smp_mb' [-Werror=implicit-function-declaration]
In this case, smp_mb() is from the cpu_relax() call in the msm putc().
It likely went uncaught when the uncompress.h change went in since the
defconfig didn't enable that code path, but later changes (e76f4750f4:
ARM: debug: arrange Kconfig options more logically) resulted in the
option being on for msm_defconfig and thus exposed it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This fixes the thrd->req_running field being accessed before thrd
is checked for null. The error was introduced in
abb959f: ARM: 7237/1: PL330: Fix driver freeze
Reference: <1326458191-23492-1-git-send-email-mans.rullgard@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Mans Rullgard <mans.rullgard@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
dst_cache_ctrl affects bits 3, 1 and 0 of AWCACHE but it is a 3-bit
field in the Channel Control Register (see Table 3-21 of the DMA-330
Technical Reference Manual) and should be programmed as such.
Reference: <1320244259-10496-3-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Bootup with lockdep enabled has been broken on v7 since b46c0f74657d
("ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR").
This is because v7_setup (which is called very early during boot) calls
v7_flush_dcache_all, and the save_and_disable_irqs added by that patch
ends up attempting to call into lockdep C code (trace_hardirqs_off())
when we are in no position to execute it (no stack, MMU off).
Fix this by using a notrace variant of save_and_disable_irqs. The code
already uses the notrace variant of restore_irqs.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch expands the Kconfig dependencies for ARM_LPAE to not allow
enabling when architectures other than ARMv7 are built into the kernel.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: OMAP2+: board-generic: Add missing handle_irq callbacks
|
|
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
|
|
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
|
|
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7322/1: Print BUG instead of undefined instruction on BUG_ON()
ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR
ARM: 7320/1: Fix proc_info table alignment
|
|
Driver at91_ide is broken and should not be fixed: remove it.
Modification of device files that where making use of it. The
PATA driver (pata_at91) is able to replace at91_ide.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
SMC, Static Memory Controller will need more accessors to fine
configure its parameters.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Registration of at91_udc as a module will enable SoC
related code.
Fix following an idea from Karel Znamenacek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Karel Znamenacek <karel@ryston.cz>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
|
|
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
While trying to debug my OMAP platforms, they emitted this message:
omap_hwmod: %s: enabled state can only be entered from initialized, idle, or disabled state
The following backtrace said it was from a function called '_enable',
which didn't provide much clue. Grepping didn't find it either.
The message is wrapped, so unwrap the message so grep can find it. Do
the same for three other messages in this file.
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The previous commit causes new section mismatch warnings:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb30): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb4c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb60): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb6c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb78): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb90): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb9c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdba8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbc0): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbcc): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbd8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbf8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc04): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc10): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc28): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc34): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc40): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc58): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc64): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc70): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc7c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Again, as for omap2_hsmmc_init(), these functions are callable at
runtime via the gpio-twl4030.c driver, and so these can't be marked
__init.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.
Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: vmlinux.o(.text+0x1c664): Section mismatch in reference from the function omap_secondary_startup() to the function .cpuinit.text:secondary_startup()
The function omap_secondary_startup() references
the function __cpuinit secondary_startup().
This is often because omap_secondary_startup lacks a __cpuinit
annotation or the annotation of secondary_startup is wrong.
Unfortunately, fixing this causes a new warning which is harder to
solve:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x5328): Section mismatch in reference from the function omap4_hotplug_cpu() to the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
because omap4_hotplug_cpu() is used by power management code as well,
which may not end up using omap_secondary_startup().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Found by review.
omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.
The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().
So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15a4): Section mismatch in reference from the function omap_mux_init_signals() to the function .init.text:omap_mux_init_signal()
The function omap_mux_init_signals() references
the function __init omap_mux_init_signal().
This is often because omap_mux_init_signals lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On my OMAP4 platform, I'm getting this error message repeated several
times at boot:
omap_vc_i2c_init: I2C config for all channels must match.
omap_vc_i2c_init: I2C config for all channels must match.
This doesn't help identify what the problem is. Fix this message to
be more informative:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
This allows us to identify which voltage domains have a problem, and
what the I2C configuration state (a boolean, i2c_high_speed) setting
being used actually is.
From this we find that omap4_core_pmic has i2c_high_speed false, but
omap4_iva_pmic and omap4_mpu_pmic both have it set true.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
While testing on my OMAP3430 platform, this error message was emitted:
omap_vc_init_channel: PMIC info requried to configure vc forvdd_core not populated.Hence cannot initialize vc
Trying to find this message was difficult because it was wrapped across
several lines. It also mis-spells "required", doesn't read very well,
and has spaces lacking. Let's replace it with a more concise:
omap_vc_init_channel: No PMIC info for vdd_core
While we're here, fix a simple spelling error in a comment.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When CONFIG_OF is disabled, the compile fails with:
arch/arm/mach-omap2/prm44xx.c:41: error: 'OMAP44XX_IRQ_PRCM' undeclared here (not in a function)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Fix build breakage due to the following commits:
Commit bd5f12a24766c1f299def0a78b008d4746f528f2
ARM: 7042/3: mach-ep93xx: break out GPIO driver specifics
Commit 257af9f9725aa8a863b306659208a031135d59e7
ARM: 7041/1: gpio-ep93xx: hookup the to_irq callback in the driver
The vision_ep9307 machine uses the ep93xx build-in gpios and needs to
include <mach/gpio-ep93xx.h> to pickup the defines.
The gpio_to_irq() call is now a callback to the gpio-ep93xx.c driver
and cannot be used as a constant initializer for the .irq member of
struct i2c_board_info.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: tegra: dma: fix buildbreak for !CONFIG_TEGRA_SYSTEM_DMA
|
|
next/soc
* 'for-arm-soc' of git://sources.calxeda.com/kernel/linux: (247 commits)
ARM: highbank: remove unused memory.h
ARM: highbank: enable sp804 based sched_clock
ARM: timer-sp: add sched_clock support
Linux 3.3-rc3
pcmcia: fix socket refcount decrementing on each resume
mm: fix UP THP spin_is_locked BUGs
drivers/leds/leds-lm3530.c: fix setting pltfm->als_vmax
mm: compaction: check for overlapping nodes during isolation for migration
nilfs2: avoid overflowing segment numbers in nilfs_ioctl_clean_segments()
ASoC: wm8994: Disable line output discharge prior to ramping VMID
ASoC: wm8994: Fix typo in VMID ramp setting
ALSA: oxygen, virtuoso: fix exchanged L/R volumes of aux and CD inputs
ALSA: usb-audio: add Edirol UM-3G support
checkpatch: Warn on code with 6+ tab indentation
ACPI: remove duplicated lines of merging problems with acpi_processor_add
ALSA: hda - add support for Uniwill ECS M31EI notebook
HID: wiimote: fix invalid power_supply_powers call
ALSA: hda - Fix error handling in patch_ca0132.c
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
...
|
|
memory.h is empty and no longer needed to build, so remove it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Initialize sched_clock to use the sp804 timer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
Add a sched_clock support for the sp804 timer. The clocksource timer
can optionally initialize itself as sched_clock timer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
|
On OMAP2420-based systems, the PM code ignores the state of the UART
functional clocks when determining what idle state to enter. This
breaks the serial port now that the UART driver's clock behavior can
be controlled via the PM autosuspend timeout.
To fix, remove the special-case idle handling for the UARTs in the
OMAP2420/2430 PM idle code added by commit
4af4016c53f52b26461b8030211f8427a58fa5ed ("OMAP3: PM: UART: disable
clocks when idle and off-mode support").
Tested on Nokia N800. This patch is a collaboration between Tony
Lindgren <tony@atomide.com> and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a928081d391cd9a570afe3b2c692fdc broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
