| Age | Commit message (Collapse) | Author |
|---|
|
This patch updates the keypad IF base address in the memory map
for EXYNOS4.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds the samsung_keypad_cfg_gpio() for EXYNOS4.
Now, this helpers are only for keypad operating in PORT-0.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Some chained IRQ handlers are written to cope with primary chips of
potentially different flow types. Whether this a sensible thing to do
is a point of contention.
This patch introduces entry/exit functions for chained handlers which
infer the flow type of the primary chip as fasteoi or level-type by
checking whether or not the ->irq_eoi function pointer is present and
calling back to the primary chip as necessary. Other methods of flow
control are not considered.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Adds the device definitions, platform specific initialization
and clocks for SATA on ARMLEX4210.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into devel-stable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into devel-stable
|
|
commit 522d7dec(futex: Remove redundant pagefault_disable in
futex_atomic_cmpxchg_inatomic()) added a bogus comment.
/* Note that preemption is disabled by futex_atomic_cmpxchg_inatomic
* call sites. */
Bogus in two aspects:
1) pagefault_disable != preempt_disable even if the mechanism we use
is the same
2) we have a call site which deliberately does not disable pagefaults
as it wants the possible fault to be handled - though that has been
changed for consistency reasons now.
Sigh. I really should have seen that when committing the above. :(
Catched-by-and-rightfully-ranted-at-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1103141126590.2787@localhost6.localdomain6>
Cc: Michel Lespinasse <walken@google.com>
Cc: Darren Hart <darren@dvhart.com>
|
|
|
|
The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.
While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
request_mem_region() error exit will leak ioremapped memory. Fix this
by moving the ioremap() after request_mem_region(), which is the proper
order to do this anyway.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove duplicate mux modes to make the binary smaller:
text data bss dec hex filename
9378 24472 0 33850 843a mux44xx.o
9378 19104 0 28482 6f42 mux44xx.o
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently IOVMM driver sets IOVMF_DA_FIXED/IOVMF_DA_ANON flags according
to input 'da' address when mapping memory:
da == 0: IOVMF_DA_ANON
da != 0: IOVMF_DA_FIXED
It prevents IOMMU to map first page with fixed 'da'. To avoid such
issue, IOVMM will not automatically set IOVMF_DA_FIXED. It should now
come from the user throught 'flags' parameter when mapping memory.
As IOVMF_DA_ANON and IOVMF_DA_FIXED are mutually exclusive, IOVMF_DA_ANON
can be removed. The driver will now check internally if IOVMF_DA_FIXED
is set or not.
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit c7f4ab26e3bcdaeb3e19ec658e3ad9092f1a6ceb allowed mapping the NULL
address if da_start==0, which would then not get unmapped. Disallow
this again if IOVMF_DA_ANON is set. And spell variable 'alignment'
correctly.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
All platform data has to be made conditional on
as to avoid cluttering the code with other #ifdef:s.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.
Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.
Cc: Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This will centralize all GPIO pin muxing for the different boards
in the MOP500 family to a single file. It also kills off the
deprecated support for the ED (Early Drop) ASIC, this should
never be spotted in the open and ST-Ericsson have internally
deprecated this hardware.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Rebasing and kill old ASIC support]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Signed-off-by: Rikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.
This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Coverity found that we were checking an unsigned variable for
>= zero. Type it correctly so that the check works as intended.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Suspend/resume didn't take care of pull-up and pull-down
settings and writing back the DAT register at resume can
change pull up/down settings, depending on pin input value.
Output values are now also restored.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Added constant 32-pin assignment in platform data]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This will configure the platform data for the PL180, PL011 and
PL022 PrimeCells found in the U300 to use DMA with the generic
PrimeCell DMA engine for COH 901 318.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mmci driver can handle a GPIO pin for card detect, using
IRQs and all just fine, so switch to using that. Delete the
old bogus input device hack, if userspace need to detect
MMC cards it should use udev like everyone else.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- MUSB is enabled with soc specific base address, irq and dma
configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
MUSB driver has been updated to separate out BSP layer
from its generic parts, as separate driver. This patch
configures the clock with the new platform driver name.
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The levelshifter pins were set to inverted values, fix this up.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The clock speed for the SD/MMC clock was incorrect, rectify it.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We register keypads per-UIB now, remove this.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The U8500 UIB contains a Synaptics RMI touchpanel and
a matrix keyboard via the TC35893 port expander device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The ST-UIB contains a matrix keypad interfaced with the
STMPE1601 port expander and a ROHM BU2101 touch panel.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for dynamic detection of the UIB used (at the cost of one i2c error
on the lesser-used UIB) and also provide an override via a command line
parameter if needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Include ab8500 regulators for DB8500 SoC by default
and fix build issues
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
[Small fixup for changed boardfiles]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Try to make the regulators a little bit more useful by adding some
of the most basic consumers we're going to have in the end.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the PMU resources necessary to get perf working with
the DB5500 ASIC.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-tcc into devel-stable
|
