| Age | Commit message (Collapse) | Author |
|---|
|
When the signal stack frame is created, it must be flushed in order to
make sure the cache fetches the correct data.
Without cache flush the icache might pick up old cached data from an older
signal stack frame if the signal is raised again very fast.
In case of copyback the data cache muist be pushed first, but is untested.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
the first one is equal to signal_pt_regs(), the second is never used
(and always NULL, while we are at it).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
TIF_NOTIFY_RESUME added (as bit 5). That way nommu glue needs no changes at
all; mmu one needs just to replace jmi do_signal_return to jne do_signal_return
There we have flags shifted up, until bit 6 (SIGPENDING) is in MSBit; instead
of checking that MSBit is set (jmi) we check that MSBit or something below it
is set (jne); bits 0..4 are never set, so that's precisely "bit 6 or bit 5 is
set".
Usual handling of NOTIFY_RESUME/SIGPENDING is done in do_notify_resume(); glue
calls it instead of do_signal().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f28f
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate code
across architectures. In the past some architectures got this code wrong,
so using this helper function should stop that from happening again.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
guts of saved_sigmask-based sigsuspend/rt_sigsuspend. Takes
kernel sigset_t *.
Open-coded instances replaced with calling it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The MMU (signal_mm.c) and non-MMU (signal_no.c) versions of the m68k
architecture signal handling code are very similar. Most of their code is
the same.
Merge the two back into a single signal.c, and move some of the code around
inside the file to minimize the number of #ifdefs required. Specificially
we can group out the CONFIG_FPU and the CONFIG_MMU code. We end up needing
a few other "#ifdef CONFIG_MMU" as well, but not too many.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
There is a lot of common code that could be shared between the m68k
and m68knommu arch branches. It makes sense to merge the two branches
into a single directory structure so that we can more easily share
that common code.
This is a brute force merge, based on a script from Stephen King
<sfking@fdwdc.com>, which was originally written by Arnd Bergmann
<arnd@arndb.de>.
> The script was inspired by the script Sam Ravnborg used to merge the
> includes from m68knommu. For those files common to both arches but
> differing in content, the m68k version of the file is renamed to
> <file>_mm.<ext> and the m68knommu version of the file is moved into the
> corresponding m68k directory and renamed <file>_no.<ext> and a small
> wrapper file <file>.<ext> is used to select between the two version. Files
> that are common to both but don't differ are removed from the m68knommu
> tree and files and directories that are unique to the m68knommu tree are
> moved to the m68k tree. Finally, the arch/m68knommu tree is removed.
>
> To select between the the versions of the files, the wrapper uses
>
> #ifdef CONFIG_MMU
> #include <file>_mm.<ext>
> #else
> #include <file>_no.<ext>
> #endif
On top of this file merge I have done a simplistic merge of m68k and
m68knommu Kconfig, which primarily attempts to keep existing options and
menus in place. Other than a handful of options being moved it produces
identical .config outputs on m68k and m68knommu targets I tested it on.
With this in place there is now quite a bit of scope for merge cleanups
in future patches.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Add helper function handle_kernel_fault() in signal.c, so frame_extra_sizes
can become static, and to avoid future code duplication.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
a) we should hold modifying regs->format until we know we *will* be
doing stack expansion; otherwise attacker can modify sigframe to
have wrong ->sc_formatvec and install SIGSEGV handler.
b) we should *not* mix copying saved extra stuff from userland with
expanding the stack; once we'd done that manual memmove, we'd better
not return to C, so cleanup is very hard to do. The easiest way
is to copy it on stack first, making sure we won't overwrite on stack
expansion. Fortunately that's easy to do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Same principle as with the previous patch - do not destroy the
state if sigframe setup fails. Incidentally, it's actually
_less_ work - we don't need to go through adjust_stack dance
on failure if we don't touch regs->stkadj until we know we'd
written sigframe out.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
If we'd failed in setup_frame(), we've no place to store
the original sigmask. It's not an unrecoverable situation -
we raise SIGSEGV, but that SIGSEGV might be successfully
handled (e.g. on altstack). In that case we really don't
want sa_mask of original signal permanently slapped on
the set of blocked signals.
Standard solution: have setup_frame()/setup_rt_frame()
report failure and don't mess with the signal-related
state if that has happened...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Instead of checking the return value of do_signal() we can just do
the work (raise SIGTRAP and clear SR.T1) directly in handle_signal(),
when setting the sigframe up. Simplifies the assembler glue and is
closer to the way we do it on other targets.
Note that do_delayed_trace does *not* disappear; it's still needed
to deal with single-stepping through syscall, since 68040 doesn't
raise the trace exception at all if the trap exception is pending.
We hit it after returning from sys_...() if TIF_DELAYED_TRACE is
set; all that has changed is that we don't reuse it for "single-step
into the handler" codepath.
As the result, do_signal() doesn't need to return anything anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
and saner do_signal() arguments, while we are at it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
... and had been such since the introduction of get_signal_to_deliver()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The following patch defines sigcontext ABI of ColdFire. Due to ISA
restrictions ColdFire needs different rt_sigreturn trampoline.
And due to ColdFire FP registers being 8-bytes instead of 12-bytes on
m68k, sigcontext and fpregset structures should be updated.
Regarding the sc_fpstate[16+6*8] field, it would've been enough 16
bytes to store ColdFire's FP state. To accomodate GLIBC's libSegFault
it would'be been enough 6*8 bytes (room for the 6 non-call-clobbered
FP registers). I set it to 16+6*8 to provide some extra space for any
future changes in the ColdFire FPU.
Signed-off-by: Maxim Kuvyrkov <maxim@codesourcery.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Make restart blocks working, required for proper syscall restarting.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
- When setting a sighandler using sigaction() call, if the flag
SA_ONSTACK is set and no alternate stack is provided via sigaltstack(),
the kernel still try to install the alternate stack. This behavior is
the opposite of the one which is documented in Single Unix Specifications
V3.
- Also when setting an alternate stack using sigaltstack() with the flag
SS_DISABLE, the kernel try to install the alternate stack on signal
delivery.
These two use cases makes the process crash at signal delivery.
Signed-off-by: Laurent Meyer <meyerlau@fr.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
