| Age | Commit message (Collapse) | Author |
|---|
|
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2867/
Patchwork: https://patchwork.linux-mips.org/patch/2919/
Patchwork: https://patchwork.linux-mips.org/patch/2928/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Noone seems to have test hardware or care anymore. Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/2881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
From: Wolfgang Grandegger <wg@denx.de>
Add basic support for the General Purpose Router (GPR) board from
Trapeze ITS.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Use the GPIO config symbol to only build Au1000 interrupt code on chips with
compatible hw.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch replaces the general alchemy prom_putchar() implementation
in favor of board-specific versions: The UART where the output of
prom_putchar is directed to really depends on the board, the current
implementation hardcodes this on a per-SoC basis which is just wrong.
So a generic uart tx function is provided in the alchemy headers,
and the boards can provide their own prom_putchar with custom
destination uart, and all in-kernel alchemy boards support
early printk.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The current in-kernel Alchemy GPIO support is far too inflexible for
all my use cases. To address this, the following changes are made:
* create generic functions which deal with manipulating the on-chip
GPIO1/2 blocks. Such functions are universally useful.
* Macros for GPIO2 shared interrupt management and block control.
* support for both built-in CONFIG_GPIOLIB and fast, inlined GPIO macros.
If CONFIG_GPIOLIB is not enabled, provide linux gpio framework
compatibility by directly inlining the GPIO1/2 functions. GPIO access
is limited to on-chip ones and they can be accessed as documented in
the datasheets (GPIO0-31 and 200-215).
If CONFIG_GPIOLIB is selected, two (2) gpio_chip-s, one for GPIO1 and
one for GPIO2, are registered. GPIOs can still be accessed by using
the numberspace established in the databooks.
However this is not yet flexible enough for my uses: My Alchemy
systems have a documented "external" gpio interface (fixed, different
numberspace) and can support a variety of baseboards, some of which
are equipped with I2C gpio expanders. I want to be able to provide
the default 16 GPIOs of the CPU board numbered as 0..15 and also
support gpio expanders, if present, starting as gpio16.
To achieve this, a new Kconfig symbol for Alchemy is introduced,
CONFIG_ALCHEMY_GPIO_INDIRECT, which boards can enable to signal
that they don't want the Alchemy numberspace exposed to the outside
world, but instead want to provide their own. Boards are now respon-
sible for providing the linux gpio interface glue code (either in a
custom gpio.h header (in board include directory) or with gpio_chips).
To make the board-specific inlined gpio functions work, the MIPS
Makefile must be changed so that the mach-au1x00/gpio.h header is
included _after_ the board headers, by moving the inclusion of
the mach-au1x00/ to the end of the header list.
See arch/mips/include/asm/mach-au1x00/gpio.h for more info.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
__do_IRQ() is deprecated and will go away.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch converts the GPIO board code to use gpiolib.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add support for the 32 kHz counter1 (RTC) as clocksource / clockevent
device. As a nice side effect, this also enables use of the 'wait'
instruction for runtime idle power savings.
If the counters aren't enabled/working properly, fall back on the
cp0 counter clock code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch attempts to modernize core Alchemy interrupt handling code.
- add irq_chips for irq controllers instead of irq type,
- add a set_type() hook to change irq trigger type during runtime,
- add a set_wake() hook to control GPIO0..7 based wakeup,
- use linux' IRQF_TRIGGER_ constants instead of homebrew ones,
- enable GENERIC_HARDIRQS_NO__DO_IRQ.
- simplify plat_irq_dispatch
- merge au1xxx_irqmap into irq.c file, the only place where its
contents are referenced.
- board_init_irq() is now mandatory for every board; use it to register
the remaining (gpio-based) interrupt sources; update all boards
accordingly.
Run-tested on Db1200 and other Au1200 based platforms.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/common/au1xxx_irqmap.c
|
|
It's more than the au1000 these days.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
