| Age | Commit message (Collapse) | Author |
|---|
|
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2867/
Patchwork: https://patchwork.linux-mips.org/patch/2919/
Patchwork: https://patchwork.linux-mips.org/patch/2928/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Noone seems to have test hardware or care anymore. Drop PB1000 support
and along with it the old Alchemy PCMCIA socket driver.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/2881/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
[Ralf: Remove a forgotten -Werror in Pb1200 Makefile.]
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Create own directory for DB1200 code and update it with new features.
- SPI support:
- tmp121 temperature sensor
- SPI flash on DB1200
- I2C support
- NE1619 sensor
- AT24 eeprom
- I2C/SPI can be selected at boot time via switch S6.8
- Carddetect IRQs for SD cards.
- gen_nand based NAND support.
- hexleds count sleep/wake transitions.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Warnings being suppressed, we can now turn on -Werror for boards which did
not have it already (devboards and xss1500).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Register the PCMCIA driver on all boards supported by it,
get rid of now-unused pcmcia macros in the board headers
(and subsequently empty pb1100/pb1500 ones).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All Alchemy development boards have external CPLDs with a few registers
in them. They all share an identical register layout with only a few
minor differences (except the PB1000) in bit functions and base
addresses.
This patch
- adds a primitive facility to initialize and use these external
registers,
- replaces all occurrences of bcsr->xxx accesses with calls to the new
functions (the pb1200 cascade irq handling code is special).
- collects BCSR register information scattered throughout the board
headers in a central place.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Replace the current sysctl-based suspend interface with a new sysfs-
based one which also uses the Linux-2.6 suspend model.
To configure wakeup sources, a subtree for the demoboards is created
under /sys/power/db1x:
sys/
`-- power
`-- db1x
|-- gpio0
|-- gpio1
|-- gpio2
|-- gpio3
|-- gpio4
|-- gpio5
|-- gpio6
|-- gpio7
|-- timer
|-- timer_timeout
|-- wakemsk
`-- wakesrc
The nodes 'gpio[0-7]' and 'timer' configure the GPIO0..7 and M2
bits of the SYS_WAKEMSK (wakeup source enable) register. Writing '1'
enables a wakesource, 0 disables it.
The 'timer_timeout' node holds the timeout in seconds after which the
TOYMATCH2 event should wake the system.
The 'wakesrc' node holds the SYS_WAKESRC register after wakeup (in hex),
the 'wakemsk' node can be used to get/set the wakeup mask directly.
For example, to have the timer wake the system after 10 seconds of sleep,
the following must be done in userspace:
echo 10 > /sys/power/db1x/timer_timeout
echo 1 > /sys/power/db1x/timer
echo mem > /sys/power/sleep
This patch also removes the homebrew CPU frequency switching code. I don't
understand how it could have ever worked reliably; it does not communicate
the clock changes to peripheral devices other than uarts.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/alchemy/devboards/pm.c
|
|
Share some code and merge small files:
- Extract the prom init code from all devboard files (they only differ in
memory configuration).
- Merge the irq configuration into board setup code.
- Merge smaller files into board setup code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
delete mode 100644 arch/mips/alchemy/devboards/db1x00/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1000/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1000/irqmap.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1100/irqmap.c
delete mode 100644 arch/mips/alchemy/devboards/pb1200/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1500/irqmap.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/init.c
delete mode 100644 arch/mips/alchemy/devboards/pb1550/irqmap.c
create mode 100644 arch/mips/alchemy/devboards/prom.c
|
|
This should ease sharing of common devboard code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
