| Age | Commit message (Collapse) | Author |
|---|
|
The CBUS UART's interrupt number was wrong conflicting with the interrupt
being tied to the Intel PIIX4. Since the PIIX4's interrupt is registered
before the CBUS UART which is not being used on most systems this would
not be noticed.
Attempts to open the ttyS2 CBUS UART would result in:
genirq: Flags mismatch irq 18. 00000000 (serial) vs. 00010000 (XT-PIC cascade)
serial_link_irq_chain: request failed: -16 for irq: 18
Qemu was written to match the kernel so will need to be fixed also.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB gadget patches from Felipe:
"usb: gadget: patches for v3.8
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place."
|
|
The internal GPHYs need a firmware blob to function properly. This patch adds
the code needed to request the blob and load it to the PHY.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4523
|
|
The XRX200 family of SoCs has embedded gigabit PHYs. This patch adds code to
boot them up.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4522
|
|
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4521
|
|
Print the hardware revision and port/channel info when starting the dma core.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4520
|
|
The XRX200 SoC family has a different register layout for reading the boot
selection bits.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4519
|
|
The bootmem was incorrectly freed resulting in lots of dangling pointers.
Additionally we should use of_platform_populate() as the Documentaion tells us
to do so.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4518
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a typo in the code.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4434
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Update stmmac_mdio_bus_data accordingly due to the upstream change.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4433
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Improve ls1x_serial_setup().
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4432
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Use common clock infrastructure instead of private APIs.
1. Enable COMMON_CLK in the Kconfig.
2. Remove private clock APIs, which are replaced by the code in
drivers/clk/clk-ls1x.c.
3. Modify header file for drivers/clk/clk-ls1x.c.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4431
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
On XLR/XLS, the cpu cores communicate with fast on-chip devices
(e.g. network accelerator, security engine etc.) using the Fast
Messaging Network(FMN). The FMN queues and credits needs to be
configured and intialized before it can be used.
The co-processor 2 on XLR/XLS CPU cores has registers for FMN access,
and the XLR/XLS has custom instructions for sending and loading
messages. The FMN can deliver also per-cpu interrupts when messages
are available at the CPU.
This patch adds FMN initialization, adds interrupt setup and handling,
and also provides support for sending and receiving FMN messages.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4468
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Create struct nlm_pic_irq for interrupts handled by the PIC.
This simplifies IRQ handling for multi-SoC as well as
the single SoC cases. Also split the setup of percpu and PIC
interrupts so that we can configure the PIC interrupts for
every node.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4467
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
There can be 1, 2 or 4 SoCs(nodes) in a multi-chip XLP board. Add an
option for multi-chip boards in case of XLP, and make the number of
nodes configurable.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4470
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Upto 4 Netlogic XLP SoCs can be connected over ICI links to form a
coherent multi-node system. Each SoC has its own set of on-chip
devices including PIC. To support this, add a per SoC stucture and
use it for the PIC and SYS block addresses instead of using global
variables.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4469
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Initial code to support more than 32 cpus. The platform CPU mask
is updated from 32-bit mask to cpumask_t. Convert places that use
cpu_/cpus_ functions to use cpumask_* functions.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4464
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Remove unused and trivial PIC accesss functions, update nlm_pic_send_ipi()
and nlm_set_irt_to_cpu() to use similar logic, and use correct type for
reg in nlm_pic_disable_irt().
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4463
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
The cpuid was not passed into early_init_secondary even though the
comment indicated that it will be. Fix this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4458
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Used the hardware thread id passed in while writing to IRT in
nlm_pic_init_irt()
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4465
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Fix Kconfig for both XLR and XLP to select ZONE_DMA32 (instead of ZONE_DMA)
in case of 64-bit compilation. This can be used for devices that can only
do DMA to 32-bit address. ZONE_DMA is not useful on XLR or XLP.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4466
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
At this point early printk is available, so debugging device tree
issues is easier.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4460
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Enable Speculative Unmap Enable bit, which will enable speculative L2
cache requests for unmapped memory. This should give better performance
for kernel code/data which is in KSEG0
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4461
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
This allows us to use the r2 optimized code from kernel headers
while compilation.
Disable PGD_C0_CONTEXT option for XLP, which does not work.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4456
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Add support for XLP performance counters register in perf. Update
mips/Kconfig so that perf events can be selected for XLP.
Signed-off-by: Zi Shen Lim <zlim@netlogicmicro.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4457
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Add support for XLR and XLS processors in MIPS Oprofile code. These
processors are multi-threaded and have two counters per core. Each
counter can track either all the events in the core (global mode),
or events in just one thread.
We use the counters in the global mode, and use only the first thread
in each core to handle the configuration etc.
Signed-off-by: Madhusudan Bhat <mbhat@netlogicmicro.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4471
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Refactor nvram related functions into its own unit for easier expansion
and exposure of the values to other drivers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4516
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Use the new reset helper where appropriate.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4453
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Add a reset helper for resetting the different cores.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4455
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
The softreset register description for BCM6358 was missing, so add it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4454
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Add a PCIe clock and use that instead of directly touching the clock
control register. While at it, fail if there is no such clock.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4452
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.
The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
If there is no ieee80211 core on the devices like on the BCM4706 read
out the sprom and the other data without using a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4361
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Read out the full board data independently of the sprom version. Now we
also get the full boardflags and so on if sromrev is not set and our
code would assume a rev 1 device. When a nvram option is not set
because it is not there this is no problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4363
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.
This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
Commit 97ce2c88f9ad42e3c60a9beb9fca87abf3639faa (jump-label: initialize
jump-label subsystem much earlier) caused MIPS to break, so this was
resolved with commit 6650df3c380e0db558dbfec63ed860402c6afb2a (MIPS:
Move cache setup to setup_arch().). Unfortunately, after this commit,
the coherency kernel parameters, cca and coherentio, are no longer
processed before their values are used.
This patch fixes this problem by marking them as early_param, which
results in them being processed before they are needed.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/3961
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
The cavium code assumed that all NOR on the boot bus was
an 8-bit NOR part and hardcoded the bankwidth. The simple
solution was to add the code that queries the configuration
register for the width of the bus that has been hardware strapped
to the Cavium. This allows both 8-bit and 16-bit parts to be
discovered during boot.
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Charles Hardin <ckhardin@exablox.com>
Patchwork: http://patchwork.linux-mips.org/patch/4323
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
The new functions introduced in commit 02a5417751 (MIPS: tlbex: Deal with
re-definition of label) should be marked __cpuinit, to eliminate a
warning that can pop up when CONFIG_EXPORT_UASM is disabled:
LD arch/mips/mm/built-in.o
WARNING: arch/mips/mm/built-in.o(.text+0x2a4c): Section mismatch in reference from the function uasm_bgezl_hazard() to the function .cpuinit.text:uasm_il_bgezl()
The function uasm_bgezl_hazard() references
the function __cpuinit uasm_il_bgezl().
This is often because uasm_bgezl_hazard lacks a __cpuinit
annotation or the annotation of uasm_il_bgezl is wrong.
WARNING: arch/mips/mm/built-in.o(.text+0x2a68): Section mismatch in reference from the function uasm_bgezl_label() to the function .cpuinit.text:uasm_build_label()
The function uasm_bgezl_label() references
the function __cpuinit uasm_build_label().
This is often because uasm_bgezl_label lacks a __cpuinit
annotation or the annotation of uasm_build_label is wrong.
(This warning might not occur if the function was inlined.)
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4517
Signed-off-by: John Crispin <blogic@openwrt.org>
|
|
For non MIPSr2 processors, such as the BMIPS 5000, calls to
arch_local_irq_disable() and others may be preempted, and in doing
so a stale value may be restored to c0_status. This fix disables
preemption for such processors prior to the call and enables it
after the call.
Those functions that needed this fix have been "outlined" to
mips-atomic.c, as they are no longer good candidates for inlining.
This bug was observed in a BMIPS 5000, occuring once every few hours
in a continuous reboot test. It was traced to the write_lock_irq()
function which was being invoked in release_task() in exit.c.
By placing a number of "nops" inbetween the mfc0/mtc0 pair in
arch_local_irq_disable(), which is called by write_lock_irq(), we
were able to greatly increase the occurance of this bug. Similarly,
the application of this commit silenced the bug.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4321/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The "else clause" of most functions in bitops.h invoked
raw_local_irq_{save,restore}() and in doing so had a dependency on
irqflags.h. This fix moves said code to bitops.c, removing the
dependency.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4320/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
[ralf@linux-mips.org: No functional change but it's consistent with how
use types elsewhere in the code.]
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Kevin Cernekee cernekee@gmail.com
Cc: Jim Quinlan <jim2101024@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/4319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
So far is_compat_task() was testing for 32-bit registers if O32 support
was enabled and if O32 support was disabled but N32 enabled it was testing
for 32-bit address space. So if both O32 and N32 were enabled a N32
task was not considered a compat task, whops.
This still leaves potential cases where O32 and N32 need different treatment
unsolved. But that's another commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The File-backed Storage Gadget (g_file_storage) is being removed, since
it has been replaced by Mass Storage Gadget (g_mass_storage). This commit
changes defconfigs point to the new gadget.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> (AT91)
Acked-by: Tony Lindgren <tony@atomide.com> (OMAP1)
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> (AVR32)
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The SO_ATTACH_FILTER option is set only. I propose to add the get
ability by using SO_ATTACH_FILTER in getsockopt. To be less
irritating to eyes the SO_GET_FILTER alias to it is declared. This
ability is required by checkpoint-restore project to be able to
save full state of a socket.
There are two issues with getting filter back.
First, kernel modifies the sock_filter->code on filter load, thus in
order to return the filter element back to user we have to decode it
into user-visible constants. Fortunately the modification in question
is interconvertible.
Second, the BPF_S_ALU_DIV_K code modifies the command argument k to
speed up the run-time division by doing kernel_k = reciprocal(user_k).
Bad news is that different user_k may result in same kernel_k, so we
can't get the original user_k back. Good news is that we don't have
to do it. What we need to is calculate a user2_k so, that
reciprocal(user2_k) == reciprocal(user_k) == kernel_k
i.e. if it's re-loaded back the compiled again value will be exactly
the same as it was. That said, the user2_k can be calculated like this
user2_k = reciprocal(kernel_k)
with an exception, that if kernel_k == 0, then user2_k == 1.
The optlen argument is treated like this -- when zero, kernel returns
the amount of sock_fprog elements in filter, otherwise it should be
large enough for the sock_fprog array.
changes since v1:
* Declared SO_GET_FILTER in all arch headers
* Added decode of vlan-tag codes
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch defines new ioctl codes TIOCGPKT, TIOCGPTLCK,
TIOCGEXCL for fetching pty's packet mode and locking state,
and exclusive mode of tty.
[ No real handlers for the codes though, this will be
addressed in another patch for easier review and
bisectability ]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
