| Age | Commit message (Collapse) | Author |
|---|
|
We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The KERNEL_SYSCALL define is not used anymore so the header can be
removed.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The parisc architecture does not have a pte special bit. As a result,
special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags.
VM_MIXEDMAP mappings may or may not have a "struct page" backing. When
pfn_valid() is false, there is no "struct page" backing. Otherwise, they
are treated as normal pages.
The FireGL driver uses the VM_MIXEDMAP without a backing "struct page".
This treatment caused a panic due to a TLB data miss in
update_mmu_cache. This appeared to be in the code generated for
page_address(). We were in fact using a very circular bit of code to
determine the physical address of the PFN in various cache routines.
This wasn't valid when there was no "struct page" backing. The needed
address can in fact be determined simply from the PFN itself without
using the "struct page".
The attached patch updates update_mmu_cache(), flush_cache_mm(),
flush_cache_range() and flush_cache_page() to check pfn_valid() and to
directly compute the PFN physical and virtual addresses.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the parisc uses of the __cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
I still see the occasional random segv on rp3440. Looking at one of
these (a code 15), it appeared the problem must be with the cache
handling of anonymous pages. Reviewing this, I noticed that the space
register %sr1 might be being clobbered when we flush an anonymous page.
Register %sr1 is used for TLB purges in a couple of places. These
purges are needed on PA8800 and PA8900 processors to ensure cache
consistency of flushed cache lines.
The solution here is simply to move the %sr1 load into the TLB lock
region needed to ensure that one purge executes at a time on SMP
systems. This was already the case for one use. After a few days of
operation, I haven't had a random segv on my rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
|
|
We want the tty fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
flush_dcache_page_asm and flush_icache_page_asm
The comment at the start of pacache.S states that the base and index
registers used for fdc,fic, and pdc instructions should not use shadowed
registers. Although this is probably unnecessary for tmpalias flushes,
there is also no reason not to comply.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
pci_mmap_page_range() is needed for X11-server support on C8000 with ATI
FireGL card.
Signed-off-by Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The C8000 workstation (64 bit kernel only) has a somewhat different
serial port configuration than other models.
Thomas Bogendoerfer sent a patch to fix this in September 2010, which
was now minimally modified by me.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
|
|
'boot_args' is an input args, and 'boot_command_line' has a fix length.
So use strlcpy() instead of strcpy() to avoid memory overflow.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
'path.bc[i]' can be asigned by PCI_SLOT() which can '> 10', so sizeof(6
* "%u:" + "%u" + '\0') may be 21.
Since 'name' length is 20, it may be memory overflow.
And 'path.bc[i]' is 'unsigned char' for printing, we can be sure the
max length of 'name' must be less than 28.
So simplify thinking, we can use 28 instead of 20 directly, and do not
think of whether 'patchc.bc[i]' can '> 100'.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
We want these fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The logic to detect if the irq stack was already in use with
raw_spin_trylock() is wrong, because it will generate a "trylock failure
on UP" error message with CONFIG_SMP=n and CONFIG_DEBUG_SPINLOCK=y.
arch_spin_trylock() can't be used either since in the CONFIG_SMP=n case
no atomic protection is given and we are reentrant here. A mutex didn't
worked either and brings more overhead by turning off interrupts.
So, let's use the fastest path for parisc which is the ldcw instruction.
Counting how often the irq stack was used is pretty useless, so just
drop this piece of code.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The get_stack_use_cr30 and get_stack_use_r30 macros allocate a stack
frame for external interrupts and interruptions requiring a stack frame.
They are currently not reentrant in that they save register context
before the stack is set or adjusted.
I have observed a number of system crashes where there was clear
evidence of stack corruption during interrupt processing, and as a
result register corruption. Some interruptions can still occur during
interruption processing, however external interrupts are disabled and
data TLB misses don't occur for absolute accesses. So, it's not entirely
clear what triggers this issue. Also, if an interruption occurs when
Q=0, it is generally not possible to recover as the shadowed registers
are not copied.
The attached patch reworks the get_stack_use_cr30 and get_stack_use_r30
macros to allocate stack before doing register saves. The new code is a
couple of instructions shorter than the old implementation. Thus, it's
an improvement even if it doesn't fully resolve the stack corruption
issue. Based on limited testing, it improves SMP system stability.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
/proc/interrupts
Show number of floating point assistant and unaligned access fixup
handler in /proc/interrupts file.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
additionally clean up some whitespaces & tabs.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Impact:
1:convert all remain take_over_console to do_take_over_console
2:update take_over_console to do_take_over_console in comment
Commit dc9641895abb ("vt: delete unneeded functions
register_con_driver|take_over_console") delete take_over_console,
but forget to convert remain take_over_console's users to new API
do_take_over_console, this patch fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, race conditions exist in the handling of TLB interruptions in
entry.S. In particular, dirty bit updates can be lost if an accessed
interruption occurs just after the dirty bit interruption on a different
cpu. Lost dirty bit updates result in user pages not being flushed and
general system instability. This change adds lock and unlock macros to
synchronize all PTE and TLB updates done in entry.S. As a result,
userspace stability is significantly improved.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This patch fixes few build issues which were introduced with the last
irq stack patch, e.g. the combination of stack overflow check and irq
stack.
Furthermore we now do proper locking and change the irq bh handler
to use the irq stack as well.
In /proc/interrupts one now can monitor how huge the irq stack has grown
and how often it was preferred over the kernel stack.
IRQ stacks are now enabled by default just to make sure that we not
overflow the kernel stack by accident.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Fix up build error on UP and show correctly number of function call
(ipi) irqs.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add framework and initial values for more fine grained statistics in
/proc/interrupts.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Default kernel stack size on parisc is 16k. During tests we found that the
kernel stack can easily grow beyond 13k, which leaves 3k left for irq
processing.
This patch adds the possibility to activate an additional stack of 16k per CPU
which is being used during irq processing. This implementation does not yet
uses this irq stack for the irq bh handler.
The assembler code for call_on_stack was heavily cleaned up by John
David Anglin.
CC: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Add the CONFIG_DEBUG_STACKOVERFLOW config option to enable checks to
detect kernel stack overflows.
Stack overflows can not be detected reliable since we do not want to
introduce too much overhead.
Instead, during irq processing in do_cpu_irq_mask() we check kernel
stack usage of the interrupted kernel process. Kernel threads can be
easily detected by checking the value of space register 7 (sr7) which
is zero when running inside the kernel.
Since THREAD_SIZE is 16k and PAGE_SIZE is 4k, reduce the alignment of
the init thread to the lower value (PAGE_SIZE) in the kernel
vmlinux.ld.S linker script.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
when returning to userspace
Helge and I have found that we have a kernel stack overflow problem
which causes a variety of random failures.
Currently, we re-enable interrupts when returning from an external
interrupt incase we need to schedule or delivery
signals. As a result, a potentially unlimited number of interrupts
can occur while we are running on the kernel
stack. It is very limited in space (currently, 16k). This change
defers enabling interrupts until we have
actually decided to schedule or delivery signals. This only occurs
when we about to return to userspace. This
limits the number of interrupts on the kernel stack to one. In other
cases, interrupts remain disabled until the
final return from interrupt (rfi).
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The "b" branch instruction used in the fork_like macro only can handle
17-bit pc-relative offsets.
This fails with an out of range offset with some .config files.
Rewrite to use the "be" instruction which
can branch to any address in a space.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Include some documentation about how the parisc gateway page technically
works and how it is used from userspace.
James Bottomley is the original author of this description and it was
copied here out of an email thread from Apr 12 2013 titled:
man2 : syscall.2 : document syscall calling conventions
CC: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This patch fixes partly PAGE_SIZEs of 16K or 64K by adjusting the
assembler PTE lookup code and the assembler TEMPALIAS code. Furthermore
some data alignments for PAGE_SIZE have been limited to 4K (or less) to
not waste too much memory with greater page sizes. As a side note, the
palo loader can (currently) only handle up to 10 ELF segments which is
fixed with tighter aligning as well.
My testings indicated that the ldci command in the sba iommu coding
needed adjustment by the PAGE_SHIFT value and that the I/O PDIR Page
size was only set to 4K for my machine (C3000).
All this fixes partly the boot, but there are still quite some caching
problems left. Examples are e.g. the symbios logic driver which is
failing:
sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69
sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
CACHE TEST FAILED: DMA error (dstat=0x81).sym0: CACHE INCORRECTLY CONFIGURED.
and the tulip network driver which doesn't seem to work correctly
either:
Sending BOOTP requests .net eth0: Setting full-duplex based on MII#1
link partner capability of 05e1
..... timed out!
Beside those kernel fixes glibc will need fixes too to be able to handle
>4K page sizes.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Things like " \t" and whitespace at end of line. I'm leaving all the other
coding style errors here alone.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
kmap_atomic allows only one argument now, just move the second.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull compat cleanup from Al Viro:
"Mostly about syscall wrappers this time; there will be another pile
with patches in the same general area from various people, but I'd
rather push those after both that and vfs.git pile are in."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
syscalls.h: slightly reduce the jungles of macros
get rid of union semop in sys_semctl(2) arguments
make do_mremap() static
sparc: no need to sign-extend in sync_file_range() wrapper
ppc compat wrappers for add_key(2) and request_key(2) are pointless
x86: trim sys_ia32.h
x86: sys32_kill and sys32_mprotect are pointless
get rid of compat_sys_semctl() and friends in case of ARCH_WANT_OLD_COMPAT_IPC
merge compat sys_ipc instances
consolidate compat lookup_dcookie()
convert vmsplice to COMPAT_SYSCALL_DEFINE
switch getrusage() to COMPAT_SYSCALL_DEFINE
switch epoll_pwait to COMPAT_SYSCALL_DEFINE
convert sendfile{,64} to COMPAT_SYSCALL_DEFINE
switch signalfd{,4}() to COMPAT_SYSCALL_DEFINE
make SYSCALL_DEFINE<n>-generated wrappers do asmlinkage_protect
make HAVE_SYSCALL_WRAPPERS unconditional
consolidate cond_syscall and SYSCALL_ALIAS declarations
teach SYSCALL_DEFINE<n> how to deal with long long/unsigned long long
get rid of duplicate logics in __SC_....[1-6] definitions
|
|
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
|
|
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
cc: Helge Deller <deller@gmx.de>
cc: linux-parisc@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
User applications running on SMP kernels have long suffered from instability
and random segmentation faults. This patch improves the situation although
there is more work to be done.
One of the problems is the various routines in pgtable.h that update page table
entries use different locking mechanisms, or no lock at all (set_pte_at). This
change modifies the routines to all use the same lock pa_dbit_lock. This lock
is used for dirty bit updates in the interruption code. The patch also purges
the TLB entries associated with the PTE to ensure that inconsistent values are
not used after the page table entry is updated. The UP and SMP code are now
identical.
The change also includes a minor update to the purge_tlb_entries function in
cache.c to improve its efficiency.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The Debian experimental linux source package (3.8.5-1) build fails
with the following errors:
...
MODPOST 2016 modules
ERROR: "__ucmpdi2" [fs/btrfs/btrfs.ko] undefined!
ERROR: "__ucmpdi2" [drivers/md/dm-verity.ko] undefined!
The attached patch resolves this problem. It is based on the s390
implementation of ucmpdi2.c.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Link: http://lkml.kernel.org/r/20130321215234.956305981@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
just have the bugger take unsigned long and deal with SETVAL
case (when we use an int member in the union) explicitly.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
|
|
commit e72837e3e7bae3f182c4ac63c9424e86f1158dd0 introduced
a default SET_PERSONALITY() in include/linux/elf.h.
This breaks with our own SET_PERSONALITY define for
32bit userspace on 64bit kernel.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
clean up after commit 6e26aab98ce8a818fb1ec47f8f727a8480a9011b
(switch to generic sigaltstack)
Signed-off-by: Helge Deller <deller@gmx.de>
|
