| Age | Commit message (Collapse) | Author |
|---|
|
We moved the definition of shift_to_mmu_psize and mmu_psize_to_shift
out of hugetlbpage.c in patch "powerpc: New hugepage directory format".
These functions are not related to hugetlbpage and we want to use them
outside hugetlbpage.c We missed a definition for book3e when we moved
these functions. Add similar functions to mmu-book3e.h
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This context switches the new Event Based Branching (EBB) SPRs. The three new
SPRs are:
- Event Based Branch Handler Register (EBBHR)
- Event Based Branch Return Register (EBBRR)
- Branch Event Status and Control Register (BESCR)
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This turns Event Based Branching (EBB) on in the Hypervisor Facility Status and
Control Register (HFSCR) and Facility Status and Control Register (FSCR).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We are getting low on cpu feature bits. So rather than add a separate bit for
every new Power8 feature, add a bit for arch 2.07 server catagory and use that
instead.
Hijack the value we had for BCTAR, but swap the value with CFAR so that all the
ARCH defines are together.
Note we don't touch CPU_FTR_TM, because it is conditionally enabled if
the kernel is built with TM support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Make BHRB instructions available in problem and privileged states.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We look at both the segment base page size and actual page size and store
the pte-lp-encodings in an array per base page size.
We also update all relevant functions to take actual page size argument
so that we can use the correct PTE LP encoding in HPTE. This should also
get the basic Multiple Page Size per Segment (MPSS) support. This is needed
to enable THP on ppc64.
[Fixed PR KVM build --BenH]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We allocate one page for the last level of linux page table. With THP and
large page size of 16MB, that would mean we are wasting large part
of that page. To map 16MB area, we only need a PTE space of 2K with 64K
page size. This patch reduce the space wastage by sharing the page
allocated for the last level of linux page table with multiple pmd
entries. We call these smaller chunks PTE page fragments and allocated
page, PTE page.
In order to support systems which doesn't have 64K HPTE support, we also
add another 2K to PTE page fragment. The second half of the PTE fragments
is used for storing slot and secondary bit information of an HPTE. With this
we now have a 4K PTE fragment.
We use a simple approach to share the PTE page. On allocation, we bump the
PTE page refcount to 16 and share the PTE page with the next 16 pte alloc
request. This should help in the node locality of the PTE page fragment,
assuming that the immediate pte alloc request will mostly come from the
same NUMA node. We don't try to reuse the freed PTE page fragment. Hence
we could be waisting some space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Acked-by: Paul Mackerras <paulus@samba.org>
This patch moves the common code to 32/64 bit headers and also duplicate
4K_PAGES and 64K_PAGES section. We will later change the 64 bit 64K_PAGES
version to support smaller PTE fragments. The patch doesn't introduce
any functional changes.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This make one PMD cover 16MB range. That helps in easier implementation of THP
on power. THP core code make use of one pmd entry to track the hugepage and
the range mapped by a single pmd entry should be equal to the hugepage size
supported by the hardware.
This also switch PGD to cover 16GB. That is needed so that we can simplify the
hugetlb page walking code so that we have same pte format for explicit hugepage
and THP hugepage.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
format
We will be switching PMD_SHIFT to 24 bits to facilitate THP impmenetation.
With PMD_SHIFT set to 24, we now have 16MB huge pages allocated at PGD level.
That means with 32 bit process we cannot allocate normal pages at
all, because we cover the entire address space with one pgd entry. Fix this
by switching to a new page table format for hugepages. With the new page table
format for 16GB and 16MB hugepages we won't allocate hugepage directory. Instead
we encode the PTE information directly at the directory level. This forces 16MB
hugepage at PMD level. This will also make the page take walk much simpler later
when we add the THP support.
With the new table format we have 4 cases for pgds and pmds:
(1) invalid (all zeroes)
(2) pointer to next table, as normal; bottom 6 bits == 0
(3) leaf pte for huge page, bottom two bits != 00
(4) hugepd pointer, bottom two bits == 00, next 4 bits indicate size of table
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Change the hugepage directory format so that we can have leaf ptes directly
at page directory avoiding the allocation of hugepage directory.
With the new table format we have 3 cases for pgds and pmds:
(1) invalid (all zeroes)
(2) pointer to next table, as normal; bottom 6 bits == 0
(4) hugepd pointer, bottom two bits == 00, next 4 bits indicate size of table
Instead of storing shift value in hugepd pointer we use mmu_psize_def index
so that we can fit all the supported hugepage size in 4 bits
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With PGD_INDEX_SIZE set to 12 the existing macro doesn't work. Fix it to
use PTRS_PER_PGD
The idea originally was to have one more bit in the result of
pgd_index() than PGD_INDEX_SIZE, so that if one had an address
corresponding to the last PGD entry, and then incremented that address
by PGD_SIZE, and took pgd_index() of that, you wouldn't end up with
zero. The commit that introduced that dates back to 2002, and the
code that was sensitive to that edge case has long since been
refactored (several times), so there is no need for it these days.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
USE PTRS_PER_PTE to indicate the size of pte page. To support THP,
later patches will be changing PTRS_PER_PTE value.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
From Kumar Gala:
<<
Add support for T4 and B4 SoC families from Freescale, e6500 altivec
support, some various board fixes and other minor cleanups.
>>
|
|
As all other architectures have been converted to use vm_unmapped_area(),
we are about to retire the free_area_cache.
This change simply removes the use of that cache in
slice_get_unmapped_area(), which will most certainly have a
performance cost. Next one will convert that function to use the
vm_unmapped_area() infrastructure and regain the performance.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Provides basic enablement for perf branch stack sampling framework on
POWER8 processor based platforms. Adds new BHRB related elements into
cpu_hw_event structure to represent current BHRB config, BHRB filter
configuration, manage context and to hold output BHRB buffer during
PMU interrupt before passing to the user space. This also enables
processing of BHRB data and converts them into generic perf branch
stack data format.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch adds couple of generic functions to power_pmu structure
which would configure the BHRB and it's filters. It also adds
representation of the number of BHRB entries present on the PMU.
A new PMU flag PPMU_BHRB would indicate presence of BHRB feature.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patch adds new POWER8 instruction encoding for reading
and clearing Branch History Rolling Buffer entries. The new
instruction 'mfbhrbe' (move from branch history rolling buffer
entry) is used to read BHRB buffer entries and instruction
'clrbhrb' (clear branch history rolling buffer) is used to
clear the entire buffer. The instruction 'clrbhrb' has straight
forward encoding. But the instruction encoding format for
reading the BHRB entries is like 'mfbhrbe RT, BHRBE' where it
takes two arguments, i.e the index for the BHRB buffer entry to
read and a general purpose register to put the value which was
read from the buffer entry.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On power8 we have a new SIER (Sampled Instruction Event Register), which
captures information about instructions when we have random sampling
enabled.
Add support for loading the SIER into pt_regs, overloading regs->dar.
Also set the new NO_SIPR flag in regs->result if we don't have SIPR.
Update regs_sihv/sipr() to look for SIPR/SIHV in SIER.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In perf_ip_adjust() we potentially use the MMCRA[SLOT] field to adjust
the reported IP of a sampled instruction.
Currently the logic is written so that if the backend does NOT have
the PPMU_ALT_SIPR flag set then we assume MMCRA[SLOT] exists.
However on power8 we do not want to set ALT_SIPR (it's in a third
location), and we also do not have MMCRA[SLOT].
So add a new flag which only indicates whether MMCRA[SLOT] exists.
Naively we'd set it on everything except power6/7, because they set
ALT_SIPR, and we've reversed the polarity of the flag. But it's more
complicated than that.
mpc7450 is 32-bit, and uses its own version of perf_ip_adjust()
which doesn't use MMCRA[SLOT], so it doesn't need the new flag set and
the behaviour is unchanged.
PPC970 (and I assume power4) don't have MMCRA[SLOT], so shouldn't have
the new flag set. This is a behaviour change on those cpus, though we
were probably getting lucky and the bits in question were 0.
power5 and power5+ set the new flag, behaviour unchanged.
power6 & power7 do not set the new flag, behaviour unchanged.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For both HV and guest kernels, intialise PMU regs to something sane.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The EOI handler of MSI/MSI-X interrupts for P8 (PHB3) need additional
steps to handle the P/Q bits in IVE before EOIing the corresponding
interrupt. The patch changes the EOI handler to cover that. we have
individual IRQ chip in each PHB instance. During the MSI IRQ setup
time, the IRQ chip is copied over from the original one for that IRQ,
and the EOI handler is patched with the one that will handle the P/Q
bits (As Ben suggested).
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Building a 64-bit powerpc kernel with PR KVM enabled currently gives
this error:
AS arch/powerpc/kernel/head_64.o
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:258: Error: attempt to move .org backwards
make[2]: *** [arch/powerpc/kernel/head_64.o] Error 1
This happens because the MASKABLE_EXCEPTION_PSERIES macro turns into
33 instructions, but we only have space for 32 at the decrementer
interrupt vector (from 0x900 to 0x980).
In the code generated by the MASKABLE_EXCEPTION_PSERIES macro, we
currently have two instances of the HMT_MEDIUM macro, which has the
effect of setting the SMT thread priority to medium. One is the
first instruction, and is overwritten by a no-op on processors where
we save the PPR (processor priority register), that is, POWER7 or
later. The other is after we have saved the PPR.
In order to reduce the code at 0x900 by one instruction, we omit the
first HMT_MEDIUM. On processors without SMT this will have no effect
since HMT_MEDIUM is a no-op there. On POWER5 and RS64 machines this
will mean that the first few instructions take a little longer in the
case where a decrementer interrupt occurs when the hardware thread is
running at low SMT priority. On POWER6 and later machines, the
hardware automatically boosts the thread priority when a decrementer
interrupt is taken if the thread priority was below medium, so this
change won't make any difference.
The alternative would be to branch out of line after saving the CFAR.
However, that would incur an extra overhead on all processors, whereas
the approach adopted here only adds overhead on older threaded processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There are instances in which we do not want topology updates to occur.
In order to allow this a /proc interface (/proc/powerpc/topology_updates)
is introduced so that topology updates can be enabled and disabled.
This patch also adds a prrn_is_enabled() call so that PRRN events are
handled in the kernel only if topology updating is enabled.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Platform events such as partition migration or the new PRRN firmware
feature can cause the NUMA characteristics of a CPU to change, and these
changes will be reflected in the device tree nodes for the affected
CPUs.
This patch registers a handler for Open Firmware device tree updates
and reconfigures the CPU and node maps whenever the associativity
changes. Currently, this is accomplished by marking the affected CPUs in
the cpu_associativity_changes_mask and allowing
arch_update_cpu_topology() to retrieve the new associativity information
using hcall_vphn().
Protecting the NUMA cpu maps from concurrent access during an update
operation will be addressed in a subsequent patch in this series.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
5 bits
The firmware_has_feature() function makes it easy to check for supported
features of the hypervisor. This patch extends the capability of
firmware_has_feature() to include checking for specified bits
in vector 5 of the architecture vector as reported in the device tree.
As part of this the #defines used for the architecture vector are re-defined
such that each option has the index into vector 5 and the feature bit encoded
into it. This makes checking for architecture bits when initiating data
for firmware_has_feature much easier.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When iterating over the entries in firmware_features_table we only need
to go over the actual number of entries in the array instead of declaring
it to be bigger and checking to make sure there is a valid entry in every
slot.
This patch removes the FIRMWARE_MAX_FEATURES #define and replaces the
array looping with the use of ARRAY_SIZE().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As part of handling of PRRN events we need to check vector 5 of the
architecture vector bits reported in the device tree to ensure PRRN event
handling is enabled. To do this firmware_has_feature() is updated (in a
subsequent patch) to make this check vector 5 bits. To avoid having to
re-define bits in the architecture vector the bit definitions are moved
to prom.h.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
A PRRN event is signaled via the RTAS event-scan mechanism, which
returns a Hot Plug Event message "fixed part" indicating "Platform
Resource Reassignment". In response to the Hot Plug Event message,
we must call ibm,update-nodes to determine which resources were
reassigned and then ibm,update-properties to obtain the new affinity
information about those resources.
The PRRN event-scan RTAS message contains only the "fixed part" with
the "Type" field set to the value 160 and no Extended Event Log. The
four-byte Extended Event Log Length field is re-purposed (since no
Extended Event Log message is included) to pass the "scope" parameter
that causes the ibm,update-nodes to return the nodes affected by the
specific resource reassignment.
This patch adds a handler for RTAS events. The function
pseries_devicetree_update() (from mobility.c) is used to make the
ibm,update-nodes/ibm,update-properties RTAS calls. Updating the NUMA maps
(handled by a subsequent patch) will require significant processing,
so pseries_devicetree_update() is called from an asynchronous workqueue
to allow event processing to continue.
PRRN RTAS events on pseries systems are rare events that have to be
initiated from the HMC console for the system by an IBM tech. This allows
us to assume that these events are widely spaced. Additionally, all work
on the queue is flushed before handling any new work to ensure we only have
one event in flight being handled at a time.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Newer firmware on Power systems can transparently reassign platform resources
(CPU and Memory) in use. For instance, if a processor or memory unit is
predicted to fail, the platform may transparently move the processing to an
equivalent unused processor or the memory state to an equivalent unused
memory unit. However, reassigning resources across NUMA boundaries may alter
the performance of the partition. When such reassignment is necessary, the
Platform Resource Reassignment Notification (PRRN) option provides a
mechanism to inform the Linux kernel of changes to the NUMA affinity of
its platform resources.
When rtasd receives a PRRN event, it needs to make a series of RTAS
calls (ibm,update-nodes and ibm,update-properties) to retrieve the
updated device tree information. These calls are already handled in the
pseries_devicetree_update() routine used in partition migration.
This patch exposes pseries_devicetree_update() to make it accessible
to other pseries routines, this patch also updates pseries_devicetree_update()
to take a 32-bit scope parameter. The scope value, which was previously hard
coded to 1 for partition migration, is used for the RTAS calls
ibm,update-nodes/properties to update the device tree.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We are currently out of free bits in AT_HWCAP. With POWER8, we have
several hardware features that we need to advertise.
Tested on POWER and x86.
Signed-off-by: Michael Neuling <michael@neuling.org>
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This adds new debug feature information so that the DAWR can be
identified by userspace tools like GDB.
Unfortunately the DAWR doesn't sit nicely into the current description
that ptrace provides to userspace via struct ppc_debug_info. It doesn't
allow for specifying that only some ranges are possible or even the end
alignment constraints (DAWR only allows 512 byte wide ranges which can't
cross a 512 byte boundary).
After talking to Edjunior Machado (GDB ppc developer), it was decided
this was the best approach. Just mark it as debug feature DAWR and
tools like GDB can internally decide the constraints.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This patch adds a new line to /proc/interrupts to account for the
doorbell interrupts that each hardware thread has received. The total
interrupt count in /proc/stat will now also include doorbells.
# cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
16: 551 1267 281 175 XICS Level IPI
LOC: 2037 1503 1688 1625 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
CNT: 0 0 0 0 Performance monitoring interrupts
MCE: 0 0 0 0 Machine check exceptions
DBL: 42 550 20 91 Doorbell interrupts
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Add SPR number and bit definitions for the HFSCR (Hypervisor Facility Status
and Control Register).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Currently ptrace_get_reg returns error as a value
what make impossible to tell whether it is a correct value or error code.
The patch adds a parameter which points to the real return data and
returns an error code.
As get_user_msr() never fails and it is used in multiple places so it has not
been changed by this patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
This fixes these errors when building UP with CONFIG_KVM_BOOK3S_64_HV=y:
arch/powerpc/kvm/book3s_hv.c:1855:2: error: implicit declaration of function 'inhibit_secondary_onlining' [-Werror=implicit-function-declaration]
arch/powerpc/kvm/book3s_hv.c:1862:2: error: implicit declaration of function 'uninhibit_secondary_onlining' [-Werror=implicit-function-declaration]
cc1: all warnings being treated as errors
and this error (with CONFIG_KVM_BOOK3S_64=m, or a vmlinux link error
with CONFIG_KVM_BOOK3S_64=y):
ERROR: "smp_send_reschedule" [arch/powerpc/kvm/kvm.ko] undefined!
make[2]: *** [__modpost] Error 1
The fix for the link error is suboptimal; ideally we want a self_ipi()
function from irq.c, connected at least to the MPIC code, to initiate
an IPI to this cpu. The fix here at least lets the code build, and it
will work, just with interrupts being delayed sometimes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
PPC_PREP is marked as BROKEN since v2.6.15. Remove all PReP specific
code now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
None of the users of DEFINE_BITOP pass a postfix, and as far as I can
tell none ever did, so drop it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
|
|
Up to now the PCIe link status on Freescale PCIe controllers was only
checked once at boot time. So hotplug did not work. With this patch the
link status is checked on every config read. PCIe devices not present at
boot time are found after doing 'echo 1 >/sys/bus/pci/rescan'.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Move to keeping the SoC registers that control and config the PCI
controllers on FSL SoCs in the pci_controller struct. This allows us to
not need to ioremap() the registers in multiple different places that
use them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Now we use ESID_BITS of kernel address to build proto vsid. So rename
USER_ESIT_BITS to ESID_BITS
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.8]
|
|
This patch change the kernel VSID range so that we limit VSID_BITS to 37.
This enables us to support 64TB with 65 bit VA (37+28). Without this patch
we have boot hangs on platforms that only support 65 bit VA.
With this patch we now have proto vsid generated as below:
We first generate a 37-bit "proto-VSID". Proto-VSIDs are generated
from mmu context id and effective segment id of the address.
For user processes max context id is limited to ((1ul << 19) - 5)
for kernel space, we use the top 4 context ids to map address as below
0x7fffc - [ 0xc000000000000000 - 0xc0003fffffffffff ]
0x7fffd - [ 0xd000000000000000 - 0xd0003fffffffffff ]
0x7fffe - [ 0xe000000000000000 - 0xe0003fffffffffff ]
0x7ffff - [ 0xf000000000000000 - 0xf0003fffffffffff ]
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.8]
|
|
VSID_BITS and VSID_BITS_1T depends on the context bits and user esid
bits. Make the dependency explicit
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.8]
|
|
The e6500 core adds support for AltiVec on a Book-E class processor.
Connect up all the various exception handling code and build config
mechanisms to allow user spaces apps to utilize AltiVec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This sets the DSCR (Data Stream Control Register) in the FSCR (Facility Status
& Control Register).
Also harmonise TAR (Target Address Register) FSCR bit definition too.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since kmp takes 2 unsigned long args there should be a compat wrapper.
Since one isn't provided I think it's safer just to hook this up to not
implemented. If we need it later we can do it properly then.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The BITOP_LE_SWIZZLE macro was used in the little-endian bitops functions
for powerpc. But these functions were converted to generic bitops and
the BITOP_LE_SWIZZLE is not used anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull signal/compat fixes from Al Viro:
"Fixes for several regressions introduced in the last signal.git pile,
along with fixing bugs in truncate and ftruncate compat (on just about
anything biarch at least one of those two had been done wrong)."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
compat: restore timerfd settime and gettime compat syscalls
[regression] braino in "sparc: convert to ksignal"
fix compat truncate/ftruncate
switch lseek to COMPAT_SYSCALL_DEFINE
lseek() and truncate() on sparc really need sign extension
|
