| Age | Commit message (Collapse) | Author |
|---|
|
The initial TLB mapping for the kernel boot didn't set the memory coherent
attribute, MAS2[M], in SMP mode.
If this code supported booting a secondary processor, which it doesn't yet,
but if it did, then when a secondary processor boots, it would probably signal
the primary processor by setting a variable called something like
__secondary_hold_acknowledge. However, due to the lack of the M bit, the
primary processor would not snoop the transaction (even if a transaction were
broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed
and the CPU would never see the ack. Which would have resulted in the primary
CPU spinning for a long time, perhaps a full second before it gives up, while
it would have waited for the ack from the secondary CPU that it wouldn't have
been able to see because of the stale cache.
The value of MAS2 for the boot page TLB1 entry is a compile time constant,
so there is no need to calculate it in powerpc assembly language.
Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent
offsets within a page are ignored and should be cleared." Existing code
didn't clear them, this code does.
The same when the page of KERNELBASE is found; we don't need to use asm to
mask the lower 12 bits off.
In the code that computes the address to rfi from, don't hard code the
offset to 24 bytes, but have the assembler figure that out for us.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch add the handlers of SPE/EFP exceptions.
The code is used to emulate float point arithmetic,
when MSR(SPE) is enabled and receive EFP data interrupt or EFP round interrupt.
This patch has no conflict with or dependence on FP math-emu.
The code has been tested by TestFloat.
Now the code doesn't support SPE/EFP instructions emulation
(it won't be called when receive program interrupt),
but it could be easily added.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Move to using the same macro definition for _FP_CHOOSENAN as s390,
sh, sparc32/64. The original author didn't understand this and
matched what sparc64 was doing and they have updated to this definition.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
PowerPC float point division emulation is derived from gcc.
I reported this problem on gcc maillist and got this reply:
http://gcc.gnu.org/ml/gcc/2008-03/msg00543.html
Since UDIV_NEEDS_NORMALIZATION is not used by kernel, we should use
_FP_DIV_MEAT_1_udiv_norm to make sure the single float point
is normalized before udiv_qrnnd.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The name of the device_node field differ across the platforms, so we
have to implement inlined accessors. This is needed to avoid ugly
#ifdef in the generic code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We need to swap these out once we start using swiotlb, so add
them to dma_ops. Create CONFIG_PPC_NEED_DMA_SYNC_OPS Kconfig
option; this is currently enabled automatically if we're
CONFIG_NOT_COHERENT_CACHE. In the future, this will also
be enabled for builds that need swiotlb. If PPC_NEED_DMA_SYNC_OPS
is not defined, the dma_sync_*_for_* ops compile to nothing.
Otherwise, they access the dma_ops pointers for the sync ops.
This patch also changes dma_sync_single_range_* to actually
sync the range - previously it was using a generous
dma_sync_single. dma_sync_single_* is now implemented
as a dma_sync_single_range with an offset of 0.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Refactor the RCU based pte free code that was used on ppc64 to be used
on all powerpc.
Additionally refactor pte_free() & pte_free_kernel() into common code
between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The tlb invalidates in kmap_atomic/kunmap_atomic can be called from
IRQ context, however they are only local invalidates (on the processor
that the kmap was called on). In the future we want to use IPIs to
do tlb invalidates this causes issue since flush_tlb_page() is considered
a broadcast invalidate.
Add local_flush_tlb_page() as a non-broadcast invalidate and use it in
kmap_atomic() since we don't have enough information in the
flush_tlb_page() call to determine its local.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The 32-bit hash code didn't need it so far so we don't update
mm->cpu_vm_mask on context switch. This however will break when we
merge the RCU based page table freeing patch and other upcoming 32-bit
embedded SMP work, so this adds the update.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: avoid creation of unreachable pages in the shadow
KVM: ppc: stop leaking host memory on VM exit
KVM: MMU: fix sync of ptes addressed at owner pagetable
KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
KVM: ia64: Fix incorrect kbuild CFLAGS override
KVM: VMX: Fix interrupt loss during race with NMI
KVM: s390: Fix problem state handling in guest sigp handler
|
|
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
called only from __init, calls __init. Incidentally, it ought to be static
in file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the VM exits, we must call put_page() for every page referenced in the
shadow TLB.
Without this patch, we usually leak 30-50 host pages (120 - 200 KiB with 4 KiB
pages). The maximum number of pages leaked is the size of our shadow TLB, 64
pages.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
With the new generic smp call function helpers, I noticed the code in
smp_message_recv was a single function call in many cases. While
getting the message number from the ipi data is easy, we can reduce
the path length by a function and data-dependent switch by registering
seperate IPI actions for these simple calls.
Originally I left the ipi action array exposed, but then I realized the
registration code should be common too.
The three users each had their own name array, so I made a fourth
to convert all users to use a common one.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This implements an optimised mutex fastpath for powerpc, making use of
acquire and release barrier semantics. This takes the mutex
lock+unlock benchmark from 203 to 173 cycles on a G5.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
After commit 598056d5af8fef1dbe8f96f5c2b641a528184e5a ("[POWERPC] Fix
rmb to order cacheable vs. noncacheable"), rmb() becomes a sync
instruction, which is needed to order cacheable vs noncacheable loads.
However smp_rmb() is #defined to rmb(), and smp_rmb() can be an
lwsync.
This restores smp_rmb() performance by using lwsync there and updates
the comments.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Change 2d1b2027626d5151fff8ef7c06ca8e7876a1a510 ("powerpc: Fixup
lwsync at runtime") removed __SUBARCH_HAS_LWSYNC, causing smp_wmb to
revert back to eieio for all CPUs. This restores the behaviour
intorduced in 74f0609526afddd88bef40b651da24f3167b10b2 ("powerpc:
Optimise smp_wmb on 64-bit processors").
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We have several instances of inline assembly code that use the addic
or addic. instructions, but don't include XER in the list of clobbers.
The addic and addic. instructions affect the carry bit, which is in
the XER register.
This adds "xer" to the list of clobbers for those inline asm
statements that use addic or addic. and didn't already have it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Introduce ps3_gpu_mutex to synchronizes GPU-related operations, like:
- invoking the L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT command using the
lv1_gpu_context_attribute() hypervisor call,
- handling the PS3AV_CID_AVB_PARAM packet in the PS3 A/V Settings driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
Fixes following build error:
CC drivers/usb/gadget/fsl_qe_udc.o
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_stall_change':
drivers/usb/gadget/fsl_qe_udc.c:156: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:163: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eptx_stall_change':
drivers/usb/gadget/fsl_qe_udc.c:173: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:180: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_nack':
drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_normal':
drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_reset':
drivers/usb/gadget/fsl_qe_udc.c:325: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:342: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_register_init':
drivers/usb/gadget/fsl_qe_udc.c:515: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'ch9getstatus':
drivers/usb/gadget/fsl_qe_udc.c:1981: error: 'struct usb_ctlr' has no member named 'usb_usep'
make[2]: *** [drivers/usb/gadget/fsl_qe_udc.o] Error 1
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Since we started using the generic timekeeping code, we haven't had a
powerpc-specific version of do_gettimeofday, and hence there is now
nothing that reads the do_gtod variable in arch/powerpc/kernel/time.c.
This therefore removes it and the code that sets it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently the clock_gettime implementation in the VDSO produces a
result with microsecond resolution for the cases that are handled
without a system call, i.e. CLOCK_REALTIME and CLOCK_MONOTONIC. The
nanoseconds field of the result is obtained by computing a
microseconds value and multiplying by 1000.
This changes the code in the VDSO to do the computation for
clock_gettime with nanosecond resolution. That means that the
resolution of the result will ultimately depend on the timebase
frequency.
Because the timestamp in the VDSO datapage (stamp_xsec, the real time
corresponding to the timebase count in tb_orig_stamp) is in units of
2^-20 seconds, it doesn't have sufficient resolution for computing a
result with nanosecond resolution. Therefore this adds a copy of
xtime to the VDSO datapage and updates it in update_gtod() along with
the other time-related fields.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Now that all of the remaining dma_mapping_ops have had their
map_/unmap_single functions updated to become map/unmap_page
functions, there is no need to have the map_/unmap_single function
pointers in the dma_mapping_ops.
So, this removes them and also removes the code that does the checking
for which set of functions to use.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The pseries PCI hotplug code has a number of issues, ranging from
incorrect resource setup to crashes, depending on what is added,
when, whether it contains a bridge, etc etc....
This fixes a whole bunch of these, while actually simplifying the code
a bit, using more generic code in the process and factoring out common
code between adding of a PHB, a slot or a device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently, our PCI code uses the pcibios_fixup_bus() callback, which
is called by the generic code when probing PCI buses, for two
different things.
One is to set up things related to the bus itself, such as reading
bridge resources for P2P bridges, fixing them up, or setting up the
iommu's associated with bridges on some platforms.
The other is some setup for each individual device under that bridge,
mostly setting up DMA mappings and interrupts.
The problem is that this approach doesn't work well with PCI hotplug
when an existing bus is re-probed for new children. We fix this
problem by splitting pcibios_fixup_bus into two routines:
pcibios_setup_bus_self() is now called to setup the bus itself
pcibios_setup_bus_devices() is now called to setup devices
pcibios_fixup_bus() is then modified to call these two after reading the
bridge bases, and the OF based PCI probe is modified to avoid calling
into the first one when rescanning an existing bridge.
[paulus@samba.org - fixed eeh.h for 32-bit compile now that pci-common.c
is including it unconditionally.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The function pcibios_do_bus_setup() was used by pcibios_fixup_bus()
to perform setup that is different between the 32-bit and 64-bit
code. This difference no longer exists, thus the function is removed
and the setup now done directly from pci-common.c.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The 32-bit and 64-bit powerpc PCI code used to set up the resource
pointers of the root bus of a given PHB in completely different
places.
This unifies this in large part, by making 32-bit use a routine very
similar to what 64-bit does when initially scanning the PCI busses.
The actual setup of the PHB resources itself is then moved to a
common function in pci-common.c.
This should cause no functional change on 64-bit. On 32-bit, the
effect is that the PHB resources are going to be setup a bit earlier,
instead of being setup from pcibios_fixup_bus().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a new CPU feature bit, CPU_FTR_UNALIGNED_LD_STD, to be added
to the 64bit powerpc chips that can do unaligned load double and
store double without any performance hit.
This is added to Power6 and Cell and will be used in the next commit
to disable the code that gets the destination address aligned on
those CPUs where doing that doesn't improve performance.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
A new field has been added to the VPA as a method for the client OS to
communicate to firmware the number of page-ins it is performing when
running collaborative memory overcommit. The hypervisor will use this
information to better determine if a partition is experiencing memory
pressure and needs more memory allocated to it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
|
|
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 18404756765c713a0be4eb1082920c04822ce588 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
After the merge of the 32 and 64bit DMA code, dma_direct_ops lost
their map/unmap_single() functions but gained map/unmap_page(). This
caused a problem for Cell because Cell's dma_iommu_fixed_ops called
the dma_direct_ops if the fixed linear mapping was to be used or the
iommu ops if the dynamic window was to be used. So in order to fix
this problem we need to update the 64bit DMA code to use
map/unmap_page.
First, we update the generic IOMMU code so that iommu_map_single()
becomes iommu_map_page() and iommu_unmap_single() becomes
iommu_unmap_page(). Then we propagate these changes up through all
the callers of these two functions and in the process update all the
dma_mapping_ops so that they have map/unmap_page rahter than
map/unmap_single. We can do this because on 64bit there is no HIGHMEM
memory so map/unmap_page ends up performing exactly the same function
as map/unmap_single, just taking different arguments.
This has no affect on drivers because the dma_map_single_attrs() just
ends up calling the map_page() function of the appropriate
dma_mapping_ops and similarly the dma_unmap_single_attrs() calls
unmap_page().
This fixes an oops on Cell blades, which oops on boot without this
because they call dma_direct_ops.map_single, which is NULL.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Resources for PHB's that are dynamically added to a system are not
properly allocated in the resource tree.
Not having these resources allocated causes an oops when removing
the PHB when we try to release them.
The diff appears a bit messy, this is mainly due to moving everything
one tab to the left in the pcibios_allocate_bus_resources routine.
The functionality change in this routine is only that the
list_for_each_entry() loop is pulled out and moved to the necessary
calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
linux/crash_dump.h defines is_kdump_kernel() to be used by code that
needs to know if the previous kernel crashed instead of a (clean) boot
or reboot.
This updates the just added powerpc code to use it. This is needed
for the next commit, which will remove __kdump_flag.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Commit 54622f10a6aabb8bb2bdacf3dd070046f03dc246 ("powerpc: Support for
relocatable kdump kernel") added a magic flag value in a register to
tell purgatory that it should be a panic kernel. This part is wrong
and is reverted by this commit.
The kernel gets a list of memory blocks and a entry point from user space.
Its job is to copy the blocks into place and then branch to the designated
entry point (after turning "off" the mmu).
The user space tool inserts a trampoline, called purgatory, that runs
before the user supplied code. Its job is to establish the entry
environment for the new kernel or other application based on the contents
of memory. The purgatory code is compiled and embedded in the tool,
where it is later patched using the elf symbol table using elf symbols.
Since the tool knows it is creating a purgatory that will run after a
kernel crash, it should just patch purgatory (or the kernel directly)
if something needs to happen.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86/um-header' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
x86: canonicalize remaining header guards
x86: drop double underscores from header guards
x86: Fix ASM_X86__ header guards
x86, um: get rid of uml-config.h
x86, um: get rid of arch/um/Kconfig.arch
x86, um: get rid of arch/um/os symlink
x86, um: get rid of excessive includes of uml-config.h
x86, um: get rid of header symlinks
x86, um: merge Kconfig.i386 and Kconfig.x86_64
x86, um: get rid of sysdep symlink
x86, um: trim the junk from uml ptrace-*.h
x86, um: take vm-flags.h to sysdep
x86, um: get rid of uml asm/arch
x86, um: get rid of uml highmem.h
x86, um: get rid of uml unistd.h
x86, um: get rid of system.h -> system.h include
x86, um: uml atomic.h is not needed anymore
x86, um: untangle uml ldt.h
x86, um: get rid of more uml asm/arch uses
x86, um: remove dead header (uml module-generic.h; never used these days)
...
|
|
the only theoretical reason for it these days is ppc; aside of uml/ppc
being dead, do_signal() would be happier in arch/powerpc/kernel/signal.h
anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
|
|
This adds relocatable kernel support for kdump. With this one can
use the same regular kernel to capture the kdump. A signature (0xfeed1234)
is passed in r6 from panic code to the next kernel through kexec_sequence
and purgatory code. The signature is used to differentiate between
kdump kernel and non-kdump kernels.
The purgatory code compares the signature and sets the __kdump_flag in
head_64.S. During the boot up, kernel code checks __kdump_flag and if it
is set, the kernel will behave as relocatable kdump kernel. This kernel
will boot at the address where it was loaded by kexec-tools ie. at the
address reserved through crashkernel boot parameter.
CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump
kernel as relocatable. So the same kernel can be used as production and
kdump kernel.
This patch incorporates the changes suggested by Paul Mackerras to avoid
GOT use and to avoid two copies of the code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Manual merge of:
arch/powerpc/Kconfig
arch/powerpc/include/asm/page.h
|
|
There are two issues when we enable CONFIG_RELOCATABLE. The first is due
to the fact that phys_addr_t is now defined in linux/types.h. The second
is due to the fact that the DMA code changes expose memstart_addr to
prom_init.c
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (41 commits)
PCI: fix pci_ioremap_bar() on s390
PCI: fix AER capability check
PCI: use pci_find_ext_capability everywhere
PCI: remove #ifdef DEBUG around dev_dbg call
PCI hotplug: fix get_##name return value problem
PCI: document the pcie_aspm kernel parameter
PCI: introduce an pci_ioremap(pdev, barnr) function
powerpc/PCI: Add legacy PCI access via sysfs
PCI: Add ability to mmap legacy_io on some platforms
PCI: probing debug message uniformization
PCI: support PCIe ARI capability
PCI: centralize the capabilities code in probe.c
PCI: centralize the capabilities code in pci-sysfs.c
PCI: fix 64-vbit prefetchable memory resource BARs
PCI: replace cfg space size (256/4096) by macros.
PCI: use resource_size() everywhere.
PCI: use same arg names in PCI_VDEVICE comment
PCI hotplug: rpaphp: make debug var unique
PCI: use %pF instead of print_fn_descriptor_symbol() in quirks.c
PCI: fix hotplug get_##name return value problem
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
m32r: fix build due to notify_cpu_starting() change
powerpc: fix linux-next build failure
|
|
This patch adds support for legacy_io and legacy_mem files in
bus class directories in sysfs for powerpc
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Due to confusion between the ftrace infrastructure and the gcc profiling
tracer "ftrace", this patch renames the config options from FTRACE to
FUNCTION_TRACER. The other two names that are offspring from FTRACE
DYNAMIC_FTRACE and FTRACE_MCOUNT_RECORD will stay the same.
This patch was generated mostly by script, and partially by hand.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
