| Age | Commit message (Collapse) | Author |
|---|
|
This implements CONFIG_RELOCATABLE for 64-bit by making the kernel as
a position-independent executable (PIE) when it is set. This involves
processing the dynamic relocations in the image in the early stages of
booting, even if the kernel is being run at the address it is linked at,
since the linker does not necessarily fill in words in the image for
which there are dynamic relocations. (In fact the linker does fill in
such words for 64-bit executables, though not for 32-bit executables,
so in principle we could avoid calling relocate() entirely when we're
running a 64-bit kernel at the linked address.)
The dynamic relocations are processed by a new function relocate(addr),
where the addr parameter is the virtual address where the image will be
run. In fact we call it twice; once before calling prom_init, and again
when starting the main kernel. This means that reloc_offset() returns
0 in prom_init (since it has been relocated to the address it is running
at), which necessitated a few adjustments.
This also changes __va and __pa to use an equivalent definition that is
simpler. With the relocatable kernel, PAGE_OFFSET and MEMORY_START are
constants (for 64-bit) whereas PHYSICAL_START is a variable (and
KERNELBASE ideally should be too, but isn't yet).
With this, relocatable kernels still copy themselves down to physical
address 0 and run there.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Using LOAD_REG_IMMEDIATE to get the address of kernel symbols
generates 5 instructions where LOAD_REG_ADDR can do it in one,
and will generate R_PPC64_ADDR16_* relocations in the output when
we get to making the kernel as a position-independent executable,
which we'd rather not have to handle. This changes various bits
of assembly code to use LOAD_REG_ADDR when we need to get the
address of a symbol, or to use suitable position-independent code
for cases where we can't access the TOC for various reasons, or
if we're not running at the address we were linked at.
It also cleans up a few minor things; there's no reason to save and
restore SRR0/1 around RTAS calls, __mmu_off can get the return
address from LR more conveniently than the caller can supply it in
R4 (and we already assume elsewhere that EA == RA if the MMU is on
in early boot), and enable_64b_mode was using 5 instructions where
2 would do.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The return code from invocation of the notifier for
pSeries_reconfig_chain during update of the device tree is not
checked. This causes writes to /proc/ppc64/ofdt to update memory
properties (i.e. ibm,dyamic-reconfiguration-memory) to always
return success, instead of the result of the notifier chain.
This happens specifically when we remove/add memory from the
device tree on machines using memory specified in the
ibm,dynamic-reconfiguration-memory property of the device tree.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Evidently MACIO_FLAG_SCCA_ON was meant.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
|
|
We currently have a race when scheduling a context to a SPE -
after we have found a runnable context in spusched_tick, the same
context may have been scheduled by spu_activate().
This may result in a panic if we try to unschedule a context that has
been freed in the meantime.
This change exits spu_schedule() if the context has already been
scheduled, so we don't end up scheduling it twice.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
We currently have a race for a free SPE. With one thread doing a
spu_yield(), and another doing a spu_activate():
thread 1 thread 2
spu_yield(oldctx) spu_activate(ctx)
__spu_deactivate(oldctx)
spu_unschedule(oldctx, spu)
spu->alloc_state = SPU_FREE
spu = spu_get_idle(ctx)
- searches for a SPE in
state SPU_FREE, gets
the context just
freed by thread 1
spu_schedule(ctx, spu)
spu->alloc_state = SPU_USED
spu_schedule(newctx, spu)
- assumes spu is still free
- tries to schedule context on
already-used spu
This change introduces a 'free_spu' flag to spu_unschedule, to indicate
whether or not the function should free the spu after descheduling the
context. We only set this flag if we're not going to re-schedule
another context on this SPU.
Add a comment to document this behaviour.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
Commit 8d5636fbca202f61fdb808fc9e20c0142291d802 introduced a reference
count on SPU contexts during find_victim, but this may cause a leak in
the reference count if we later find a better contender for a context to
unschedule.
Change the reference to after we've found our victim context, so we
don't do the extra get_spu_context().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
This bug is causing random crashes
(http://bugzilla.kernel.org/show_bug.cgi?id=11414).
-fno-omit-frame-pointer is only needed on powerpc when -pg is also
supplied, and there is a gcc bug that causes incorrect code generation
on 32-bit powerpc when -fno-omit-frame-pointer is used---it uses stack
locations below the stack pointer, which is not allowed by the ABI
because those locations can and sometimes do get corrupted by an
interrupt.
This ensures that CONFIG_FRAME_POINTER is only selected by ftrace.
When CONFIG_FTRACE is enabled we also pass -mno-sched-epilog to work
around the gcc codegen bug.
Patch based on work by:
Andreas Schwab <schwab@suse.de>
Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This fixes an error building powerpc allmodconfig:
ERROR: "CMO_PageSize" [arch/powerpc/platforms/pseries/cmm.ko] undefined!
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Fix the ioremap of the spu shadow regs on the PS3.
The current PS3 hypervisor requires the spu shadow regs to be
mapped with the PTE page protection bits set as read-only (PP=3).
This implementation uses the low level __ioremap() to bypass the
page protection settings inforced by ioremap_flags() to get the
needed PTE bits set for the shadow regs.
This fixes a runtime failure on the PS3 introduced by the powerpc
ioremap_prot rework of commit a1f242ff460e4b50a045fa237c3c56cce9eabf83
("powerpc ioremap_prot").
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Rework the PS3 MMU hash table code to remove the need to ioremap the
hash table by using the HV calls lv1_insert_htab_entry() and
lv1_read_htab_entries().
This fixes a runtime failure on the PS3 introduced by the powerpc
ioremap_prot rework of commit a1f242ff460e4b50a045fa237c3c56cce9eabf83
("powerpc ioremap_prot").
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This changes powerpc to use the new bcd2bin/bin2bcd functions
instead of the obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Currently print_device_node_tree() isn't called but it can be useful for
debugging. Leave the function there but hide it behind '#if 0' to save
it being rewritten. If you want to call it you're already editing this
file anyway. ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
from_rtc_time() is only called when one of 3 CONFIG options are defined.
Guard the declaration appropriately.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
__FUNCTION__ is gcc-specific, use __func__
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jk/spufs into merge
|
|
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
If the firmware page size used for collaborative memory overcommit
is 4k, but the kernel is using 64k pages, the page loaning is currently
broken as it only marks the first 4k page of each 64k page as loaned.
This fixes this to iterate through each 4k page and mark them all as
loaned/active.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
During platform setup, save off the primary/secondary paging space
pool IDs and the page size. Added accessors in hvcall.h for these
variables. This is needed for a subsequent fix.
Submitted-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Based on an original patch from Christoph Hellwig <hch@lst.de>.
Currently, there is a possible reference-after-free in the spusched
code - contexts may be freed after we have released their state_mutex
in spusched_tick and find_victim.
This change takes a reference to the context before releasing the
mutex, so that the context doesn't get destroyed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
Currently, spu_run ignores the npc argument for contexts created with
SPU_CREATE_NOSCHED. While this is correct for isolated contexts,
there's no need to enforce the npc restriction on non-isolated NOSCHED
contexts.
This means that NOSCHED contexts can only ever run with an entry point
of 0x0.
This change to spu_run_init allows setting of the npc (and, while we're
at it, the privcntl) for non-isolated NOSCHED contexts. This allows
us to run NOSCHED contexts from any entry point.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove include/linux/harrier_defs.h
powerpc: Do not ignore arch/powerpc/include
powerpc: Delete completed "ppc removal" task from feature removal file
powerpc/mm: Fix attribute confusion with htab_bolt_mapping()
powerpc/pci: Don't keep ISA memory hole resources in the tree
powerpc: Zero fill the return values of rtas argument buffer
powerpc/4xx: Update defconfig files for 2.6.27-rc1
powerpc/44x: Incorrect NOR offset in Warp DTS
powerpc/44x: Warp DTS changes for board updates
powerpc/4xx: Cleanup Warp for i2c driver changes.
powerpc/44x: Adjust warp-nand resource end address
|
|
This driver was declared obsolete over 2 years ago, the alternative
console driver for legacy iSeries (hvc_iseries) was made the default
over 1 year ago and this driver has been build broken for over 3
months, so remove it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes the i2c code which is now obsolete due to the new
ibm iic driver walking the device tree for child nodes.
There are two other small cleanups that came indirectly from the ad7414
code review. Make sure Tlow is correct and handle the case where
i2c_smbus_read_word_data fails.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Adjust the NDFC resource end value (resource size = end - start + 1).
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
|
Now that arch/ppc is gone and CONFIG_PPC_MERGE is always set, remove
the dead code associated with !CONFIG_PPC_MERGE from arch/powerpc
and include/asm-powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
|
|
Ingo Molnar provided a fix to not call _PPC at processor driver
initialization time in "[PATCH] ACPI: fix cpufreq regression" (git
commit e4233dec749a3519069d9390561b5636a75c7579)
But it can still happen that _PPC is called at processor driver
initialization time.
This patch should make sure that this is not possible anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch introduces baudrate setting support via the generic clock API.
When present the optional device tree clock property is used instead of
fsl-cpm-brg. Platforms can then define complex clock schemes, to output
the serial clock on an external pin for instance.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch implement GPIO LIB support for the CPM1 GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.
Based on earlier work by Laurent Pinchart.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This removes the non-working code in legacy_serial that tried to handle
the powermac SCC ports, and instead add a (now working) function to the
powermac platform code to find the default serial console if any.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When using the "sccdbg" option to route early kernel messages and
xmon to the SCC serial port on PowerMacs, when this wasn't the
configured output port of Open Firmware, we initialize the baudrate
to 57600bps. This isn't a very good default on some powermacs where
both the FW and pmac_zilog will default to 38400. This fixes it to
use the same logic as pmac_zilog to pick a default speed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Noticed due to these wanings:
arch/powerpc/platforms/pseries/cmm.c:298: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:299: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
arch/powerpc/platforms/pseries/cmm.c:320: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
|
|
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To support Cooperative Memory Overcommitment (CMO), we need to check
for failure from some of the tce hcalls.
These changes for the pseries platform affect the powerpc architecture;
patches for the other affected platforms are included in this patch.
pSeries platform IOMMU code changes:
* platform TCE functions must handle H_NOT_ENOUGH_RESOURCES errors and
return an error.
Architecture IOMMU code changes:
* Calls to ppc_md.tce_build need to check return values and return
DMA_MAPPING_ERROR for transient errors.
Architecture changes:
* struct machdep_calls for tce_build*_pSeriesLP functions need to change
to indicate failure.
* all other platforms will need updates to iommu functions to match the new
calling semantics; they will return 0 on success. The other platforms
default configs have been built, but no further testing was performed.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Adds a collaborative memory manager, which acts as a simple balloon driver
for System p machines that support cooperative memory overcommitment
(CMO).
Adds a platform configuration option for CMO called PPC_SMLPAR.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Newer versions of firmware support page states, which are used by the
collaborative memory manager (future patch) to "loan" pages to the
hypervisor for use by other partitions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For Cooperative Memory Overcommitment (CMO), set the FW_FEATURE_CMO
flag in powerpc_firmware_features from the rtas ibm,get-system-parameters
table prior to calling iommu_init_early_pSeries.
With this, any CMO specific functionality can be controlled by checking:
firmware_has_feature(FW_FEATURE_CMO)
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
At the moment the fixed mapping is by default strongly ordered (the
iommu_fixed=weak boot option must be used to make the fixed mapping weakly
ordered). If we're on a setup where the southbridge is being used in
endpoint mode (triblade and CAB boards) the default should be a weakly
ordered fixed mapping.
This adds a check so that if a node of type pcie-endpoint can be found in
the device tree the fixed mapping is set to be weak by default (but can be
overridden using iommu_fixed=strong).
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
|
