| Age | Commit message (Collapse) | Author |
|---|
|
On Power8 we can freeze PMC5 and 6 if we're not using them. Normally they
run all the time.
As noticed by Anshuman, we should unfreeze them when we disable the PMU
as there are legacy tools which expect them to run all the time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In pmu_disable() we disable the PMU by setting the FC (Freeze Counters)
bit in MMCR0. In order to do this we have to read/modify/write MMCR0.
It's possible that we read a value from MMCR0 which has PMAO (PMU Alert
Occurred) set. When we write that value back it will cause an interrupt
to occur. We will then end up in the PMU interrupt handler even though
we are supposed to have just disabled the PMU.
We can avoid this by making sure we never write PMAO back. We should not
lose interrupts because when the PMU is re-enabled the overflowed values
will cause another interrupt.
We also reorder the clearing of SAMPLE_ENABLE so that is done after the
PMU is frozen. Otherwise there is a small window between the clearing of
SAMPLE_ENABLE and the setting of FC where we could take an interrupt and
incorrectly see SAMPLE_ENABLE not set. This would for example change the
logic in perf_read_regs().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
A mistake we have made in the past is that we pull out the fields we
need from the event code, but don't check that there are no unknown bits
set. This means that we can't ever assign meaning to those unknown bits
in future.
Although we have once again failed to do this at release, it is still
early days for Power8 so I think we can still slip this in and get away
with it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Similar to the facility unavailble exception, except the facilities are
controlled by HFSCR.
Adapt the facility_unavailable_exception() so it can be called for
either the regular or Hypervisor facility unavailable exceptions.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The exception at 0xf60 is not the TM (Transactional Memory) unavailable
exception, it is the "Facility Unavailable Exception", rename it as
such.
Flesh out the handler to acknowledge the fact that it can be called for
many reasons, one of which is TM being unavailable.
Use STD_EXCEPTION_COMMON() for the exception body, for some reason we
had it open-coded, I've checked the generated code is identical.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.10]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
KVMTEST is a macro which checks whether we are taking an exception from
guest context, if so we branch out of line and eventually call into the
KVM code to handle the switch.
When running real guests on bare metal (HV KVM) the hardware ensures
that we never take a relocation on exception when transitioning from
guest to host. For PR KVM we disable relocation on exceptions ourself in
kvmppc_core_init_vm(), as of commit a413f47 "Disable relocation on
exceptions whenever PR KVM is active".
So convert all the RELON macros to use NOTEST, and drop the remaining
KVM_HANDLER() definitions we have for 0xe40 and 0xe80.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have relocation on exception handlers defined for h_data_storage and
h_instr_storage. However we will never take relocation on exceptions for
these because they can only come from a guest, and we never take
relocation on exceptions when we transition from guest to host.
We also have a handler for hmi_exception (Hypervisor Maintenance) which
is defined in the architecture to never be delivered with relocation on,
see see v2.07 Book III-S section 6.5.
So remove the handlers, leaving a branch to self just to be double extra
paranoid.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
CC: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The topology update code that updates the cpu node registration in sysfs
should not be called while in stop_machine(). The register/unregister
calls take a lock and may sleep.
This patch moves these calls outside of the call to stop_machine().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
spinning_secondaries
the smp_release_cpus is a normal funciton and called in normal environments,
but it calls the __initdata spinning_secondaries.
need modify spinning_secondaries to match smp_release_cpus.
the related warning:
(the linker report boot_paca.33377, but it should be spinning_secondaries)
-----------------------------------------------------------------------------
WARNING: arch/powerpc/kernel/built-in.o(.text+0x23176): Section mismatch in reference from the function .smp_release_cpus() to the variable .init.data:boot_paca.33377
The function .smp_release_cpus() references
the variable __initdata boot_paca.33377.
This is often because .smp_release_cpus lacks a __initdata
annotation or the annotation of boot_paca.33377 is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x231fe): Section mismatch in reference from the function .smp_release_cpus() to the variable .init.data:boot_paca.33377
The function .smp_release_cpus() references
the variable __initdata boot_paca.33377.
This is often because .smp_release_cpus lacks a __initdata
annotation or the annotation of boot_paca.33377 is wrong.
-----------------------------------------------------------------------------
Signed-off-by: Chen Gang <gang.chen@asianux.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When error occurs, need return the related error code to let upper
caller know about it.
ppc_md.nvram_size() can return the error code (e.g. core99_nvram_size()
in 'arch/powerpc/platforms/powermac/nvram.c').
Also set ret value when only need it, so can save structions for normal
cases.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
It seems following race is possible:
cpu0 cpux
smp_init->cpu_up->_cpu_up
__cpu_up
kick_cpu(1)
-------------------------------------------------------------------------
waiting online ...
... notify CPU_STARTING
set cpux active
set cpux online
-------------------------------------------------------------------------
finish waiting online
...
sched_init_smp
init_sched_domains(cpu_active_mask)
build_sched_domains
set cpux sibling info
-------------------------------------------------------------------------
Execution of cpu0 and cpux could be concurrent between two separator
lines.
So if the cpux sibling information was set too late (normally
impossible, but could be triggered by adding some delay in
start_secondary, after setting cpu online), build_sched_domains()
running on cpu0 might see cpux active, with an empty sibling mask, then
cause some bad address accessing like following:
[ 0.099855] Unable to handle kernel paging request for data at address 0xc00000038518078f
[ 0.099868] Faulting instruction address: 0xc0000000000b7a64
[ 0.099883] Oops: Kernel access of bad area, sig: 11 [#1]
[ 0.099895] PREEMPT SMP NR_CPUS=16 DEBUG_PAGEALLOC NUMA pSeries
[ 0.099922] Modules linked in:
[ 0.099940] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc1-00120-gb973425-dirty #16
[ 0.099956] task: c0000001fed80000 ti: c0000001fed7c000 task.ti: c0000001fed7c000
[ 0.099971] NIP: c0000000000b7a64 LR: c0000000000b7a40 CTR: c0000000000b4934
[ 0.099985] REGS: c0000001fed7f760 TRAP: 0300 Not tainted (3.10.0-rc1-00120-gb973425-dirty)
[ 0.099997] MSR: 8000000000009032 <SF,EE,ME,IR,DR,RI> CR: 24272828 XER: 20000003
[ 0.100045] SOFTE: 1
[ 0.100053] CFAR: c000000000445ee8
[ 0.100064] DAR: c00000038518078f, DSISR: 40000000
[ 0.100073]
GPR00: 0000000000000080 c0000001fed7f9e0 c000000000c84d48 0000000000000010
GPR04: 0000000000000010 0000000000000000 c0000001fc55e090 0000000000000000
GPR08: ffffffffffffffff c000000000b80b30 c000000000c962d8 00000003845ffc5f
GPR12: 0000000000000000 c00000000f33d000 c00000000000b9e4 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000001 0000000000000000
GPR20: c000000000ccf750 0000000000000000 c000000000c94d48 c0000001fc504000
GPR24: c0000001fc504000 c0000001fecef848 c000000000c94d48 c000000000ccf000
GPR28: c0000001fc522090 0000000000000010 c0000001fecef848 c0000001fed7fae0
[ 0.100293] NIP [c0000000000b7a64] .get_group+0x84/0xc4
[ 0.100307] LR [c0000000000b7a40] .get_group+0x60/0xc4
[ 0.100318] Call Trace:
[ 0.100332] [c0000001fed7f9e0] [c0000000000dbce4] .lock_is_held+0xa8/0xd0 (unreliable)
[ 0.100354] [c0000001fed7fa70] [c0000000000bf62c] .build_sched_domains+0x728/0xd14
[ 0.100375] [c0000001fed7fbe0] [c000000000af67bc] .sched_init_smp+0x4fc/0x654
[ 0.100394] [c0000001fed7fce0] [c000000000adce24] .kernel_init_freeable+0x17c/0x30c
[ 0.100413] [c0000001fed7fdb0] [c00000000000ba08] .kernel_init+0x24/0x12c
[ 0.100431] [c0000001fed7fe30] [c000000000009f74] .ret_from_kernel_thread+0x5c/0x68
[ 0.100445] Instruction dump:
[ 0.100456] 38800010 38a00000 4838e3f5 60000000 7c6307b4 2fbf0000 419e0040 3d220001
[ 0.100496] 78601f24 39491590 e93e0008 7d6a002a <7d69582a> f97f0000 7d4a002a e93e0010
[ 0.100559] ---[ end trace 31fd0ba7d8756001 ]---
This patch tries to move the sibling maps updating before
notify_cpu_starting() and cpu online, and a write barrier there to make
sure sibling maps are updated before active and online mask.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the powerpc uses of the __cpuinit macros. There
are no __CPUINIT users in assembly files in powerpc.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
pci_iommu_init() and pci_direct_iommu_init() are not referenced anywhere,
so remove them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For an unknown relocation type since the value of r4 is just the 8bit
relocation type, the sum of r4 and r7 may yield an invalid memory
address. For example:
In normal case:
r4 = c00xxxxx
r7 = 40000000
r4 + r7 = 000xxxxx
For an unknown relocation type:
r4 = 000000xx
r7 = 40000000
r4 + r7 = 400000xx
400000xx is an invalid memory address for a board which has just
512M memory.
And for operations such as dcbst or icbi may cause bus error for an
invalid memory address on some platforms and then cause the board
reset. So we should skip the flush/invalidate the d/icache for
an unknown relocation type.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Currently, we're using the combo (PCI bus + devfn) in the PCI
config accessors and PCI config accessors in EEH depends on them.
However, it's not safe to refer the PCI bus which might have been
removed during hotplug. So we're using device node in the PCI
config accessors and the corresponding backends just reuse them.
The patch also fix one potential risk: We possiblly have frozen
PE during the early PCI probe time, but we haven't setup the PE
mapping yet. So the errors should be counted to PE#0.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The patch is for avoiding following build warnings:
The function .pnv_pci_ioda_fixup() references
the function __init .eeh_init().
This is often because .pnv_pci_ioda_fixup lacks a __init
The function .pnv_pci_ioda_fixup() references
the function __init .eeh_addr_cache_build().
This is often because .pnv_pci_ioda_fixup lacks a __init
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We needn't the the whole backtrace other than one-line message in
the error reporting interrupt handler. For errors triggered by
access PCI config space or MMIO, we replace "WARN(1, ...)" with
pr_err() and dump_stack(). The patch also adds more output messages
to indicate what EEH core is doing. Besides, some printk() are
replaced with pr_warning().
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On the PowerNV platform, the EEH address cache isn't built correctly
because we skipped the EEH devices without binding PE. The patch
fixes that.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We have 2 fields in "struct pnv_phb" to trace the states. The patch
replace the fields with one and introduces flags for that. The patch
doesn't impact the logic.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
After reset (e.g. complete reset) in order to bring the fenced PHB
back, the PCIe link might not be ready yet. The patch intends to
make sure the PCIe link is ready before accessing its subordinate
PCI devices. The patch also fixes that wrong values restored to
PCI_COMMAND register for PCI bridges.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When the PHB is fenced or dead, it's pointless to collect the data
from PCI config space of subordinate PCI devices since it should
return 0xFF's. The patch also fixes overwritten buffer while getting
PCI config data.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When we treclaim and trecheckpoint there's an unavoidable period when r1
will not be a valid kernel stack pointer.
This patch clears the MSR recoverable interrupt (RI) bit over these
regions to indicate we have an invalid kernel stack pointer.
For treclaim, the region over which we clear MSR RI is larger than
required to avoid the need for an extra costly mtmsrd.
Thanks to Paulus for suggesting this change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
String instruction emulation would erroneously result in a segfault if
the upper bits of the EA are set and is so high that it fails access
check. Truncate the EA to 32 bits if the process is 32-bit.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Sebastien Bessiere <sebastien.bessiere@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
While running Linux as guest on top of phyp, we possiblly have
PE that includes single PCI device. However, we didn't return
its PCI bus correctly and it leads to failure on recovery from
EEH errors for single-dev-PE. The patch fixes the issue.
Cc: <stable@vger.kernel.org> # v3.7+
Cc: Steve Best <sbest@us.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
While technically it's legal to write to PIR and have the identifier changed,
we don't implement logic to do so because we simply expose vcpu_id to the guest.
So instead, let's ignore writes to PIR. This ensures that we don't inject faults
into the guest for something the guest is allowed to do. While at it, we cross
our fingers hoping that it also doesn't mind that we broke its PIR read values.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
At present, if the guest creates a valid SLB (segment lookaside buffer)
entry with the slbmte instruction, then invalidates it with the slbie
instruction, then reads the entry with the slbmfee/slbmfev instructions,
the result of the slbmfee will have the valid bit set, even though the
entry is not actually considered valid by the host. This is confusing,
if not worse. This fixes it by zeroing out the orige and origv fields
of the SLB entry structure when the entry is invalidated.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
With this, the guest can use 1TB segments as well as 256MB segments.
Since we now have the situation where a single emulated guest segment
could correspond to multiple shadow segments (as the shadow segments
are still 256MB segments), this adds a new kvmppc_mmu_flush_segment()
to scan for all shadow segments that need to be removed.
This restructures the guest HPT (hashed page table) lookup code to
use the correct hashing and matching functions for HPTEs within a
1TB segment. We use the standard hpt_hash() function instead of
open-coding the hash calculation, and we use HPTE_V_COMPARE() with
an AVPN value that has the B (segment size) field included. The
calculation of avpn is done a little earlier since it doesn't change
in the loop starting at the do_second label.
The computation in kvmppc_mmu_book3s_64_esid_to_vsid() changes so that
it returns a 256MB VSID even if the guest SLB entry is a 1TB entry.
This is because the users of this function are creating 256MB SLB
entries. We set a new VSID_1T flag so that entries created from 1T
segments don't collide with entries from 256MB segments.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The loop in kvmppc_mmu_book3s_64_xlate() that looks up a translation
in the guest hashed page table (HPT) keeps going if it finds an
HPTE that matches but doesn't allow access. This is incorrect; it
is different from what the hardware does, and there should never be
more than one matching HPTE anyway. This fixes it to stop when any
matching HPTE is found.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On entering a PR KVM guest, we invalidate the whole SLB before loading
up the guest entries. We do this using an slbia instruction, which
invalidates all entries except entry 0, followed by an slbie to
invalidate entry 0. However, the slbie turns out to be ineffective
in some circumstances (specifically when the host linear mapping uses
64k pages) because of errors in computing the parameter to the slbie.
The result is that the guest kernel hangs very early in boot because
it takes a DSI the first time it tries to access kernel data using
a linear mapping address in real mode.
Currently we construct bits 36 - 43 (big-endian numbering) of the slbie
parameter by taking bits 56 - 63 of the SLB VSID doubleword. These bits
for the tlbie are C (class, 1 bit), B (segment size, 2 bits) and 5
reserved bits. For the SLB VSID doubleword these are C (class, 1 bit),
reserved (1 bit), LP (large page size, 2 bits), and 4 reserved bits.
Thus we are not setting the B field correctly, and when LP = 01 as
it is for 64k pages, we are setting a reserved bit.
Rather than add more instructions to calculate the slbie parameter
correctly, this takes a simpler approach, which is to set entry 0 to
zeroes explicitly. Normally slbmte should not be used to invalidate
an entry, since it doesn't invalidate the ERATs, but it is OK to use
it to invalidate an entry if it is immediately followed by slbia,
which does invalidate the ERATs. (This has been confirmed with the
Power architects.) This approach takes fewer instructions and will
work whatever the contents of entry 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This makes sure the calculation of the proto-VSIDs used by PR KVM
is done with 64-bit arithmetic. Since vcpu3s->context_id[] is int,
when we do vcpu3s->context_id[0] << ESID_BITS the shift will be done
with 32-bit instructions, possibly leading to significant bits
getting lost, as the context id can be up to 524283 and ESID_BITS is
18. To fix this we cast the context id to u64 before shifting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Availablity of the doorbell_exception function is guarded by
CONFIG_PPC_DOORBELL. Use the same define to guard our caller
of it.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
[agraf: improve patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"We discovered some breakage in our "EEH" (PCI Error Handling) code
while doing error injection, due to a couple of regressions. One of
them is due to a patch (37f02195bee9 "powerpc/pci: fix PCI-e devices
rescan issue on powerpc platform") that, in hindsight, I shouldn't
have merged considering that it caused more problems than it solved.
Please pull those two fixes. One for a simple EEH address cache
initialization issue. The other one is a patch from Guenter that I
had originally planned to put in 3.11 but which happens to also fix
that other regression (a kernel oops during EEH error handling and
possibly hotplug).
With those two, the couple of test machines I've hammered with error
injection are remaining up now. EEH appears to still fail to recover
on some devices, so there is another problem that Gavin is looking
into but at least it's no longer crashing the kernel."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Improve device hotplug initialization
powerpc/eeh: Add eeh_dev to the cache during boot
|
|
Commit 37f02195b (powerpc/pci: fix PCI-e devices rescan issue on powerpc
platform) fixes a problem with interrupt and DMA initialization on hot
plugged devices. With this commit, interrupt and DMA initialization for
hot plugged devices is handled in the pci device enable function.
This approach has a couple of drawbacks. First, it creates two code paths
for device initialization, one for hot plugged devices and another for devices
known during the initial PCI scan. Second, the initialization code for hot
plugged devices is only called when the device is enabled, ie typically
in the probe function. Also, the platform specific setup code is called each
time pci_enable_device() is called, not only once during device discovery,
meaning it is actually called multiple times, once for devices discovered
during the initial scan and again each time a driver is re-loaded.
The visible result is that interrupt pins are only assigned to hot plugged
devices when the device driver is loaded. Effectively this changes the PCI
probe API, since pci_dev->irq and the device's dma configuration will now
only be valid after pci_enable() was called at least once. A more subtle
change is that platform specific PCI device setup is moved from device
discovery into the driver's probe function, more specifically into the
pci_enable_device() call.
To fix the inconsistencies, add new function pcibios_add_device.
Call pcibios_setup_device from pcibios_setup_bus_devices if device setup
is not complete, and from pcibios_add_device if bus setup is complete.
With this change, device setup code is moved back into device initialization,
and called exactly once for both static and hot plugged devices.
[ This also fixes a regression introduced by the above patch which
causes dev->irq to be overwritten under some cirumstances after
MSIs have been enabled for the device which leads to crashes due
to the MSI core "hijacking" dev->irq to store the base MSI number
and not the LSI. --BenH
]
Cc: Yuanquan Chen <Yuanquan.Chen@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hiroo Matsumoto <matsumoto.hiroo@jp.fujitsu.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
new helpers - dir_emit_dot(file, ctx, dentry), dir_emit_dotdot(file, ctx),
dir_emit_dots(file, ctx).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
commit f8f7d63fd96ead101415a1302035137a866f8998 ("powerpc/eeh: Trace eeh
device from I/O cache") broke EEH on pseries for devices that were
present during boot and have not been hotplugged/DLPARed.
eeh_check_failure will get the eeh_dev from the cache, and will get
NULL. eeh_addr_cache_build adds the addresses to the cache, but eeh_dev
for the giving pci_device is not set yet. Just reordering the call to
eeh_addr_cache_insert_dev works fine. The ordering is similar to the one
in eeh_add_device_late.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
* pm-cpufreq-assorted: (21 commits)
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: e_powersaver: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: ACPI: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: make __cpufreq_notify_transition() static
cpufreq: Fix minor formatting issues
cpufreq: Fix governor start/stop race condition
cpufreq: Simplify userspace governor
cpufreq: powerpc: move cpufreq driver to drivers/cpufreq
cpufreq: kirkwood: Select CPU_FREQ_TABLE option
cpufreq: big.LITTLE needs cpufreq table
cpufreq: SPEAr needs cpufreq table
cpufreq: powerpc: Add cpufreq driver for Freescale e500mc SoCs
cpufreq: remove unnecessary cpufreq_cpu_{get|put}() calls
cpufreq: MAINTAINERS: Add git tree path for ARM specific updates
cpufreq: rename index as driver_data in cpufreq_frequency_table
cpufreq: Don't create empty /sys/devices/system/cpu/cpufreq directory
cpufreq: Move get_cpu_idle_time() to cpufreq.c
cpufreq: governors: Move get_governor_parent_kobj() to cpufreq.c
cpufreq: Add EXPORT_SYMBOL_GPL for have_governor_per_policy
...
|
|
This will allow me to call functions that have multiple
arguments if fastpath fails. This is required to support ticket
mutexes, because they need to be able to pass an extra argument
to the fail function.
Originally I duplicated the functions, by adding
__mutex_fastpath_lock_retval_arg. This ended up being just a
duplication of the existing function, so a way to test if
fastpath was called ended up being better.
This also cleaned up the reservation mutex patch some by being
able to call an atomic_set instead of atomic_xchg, and making it
easier to detect if the wrong unlock function was previously
used.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: robclark@gmail.com
Cc: rostedt@goodmis.org
Cc: daniel@ffwll.ch
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20130620113105.4001.83929.stgit@patser
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc bugfix from Ben Herrenschmidt:
"This is a fix for a regression causing a freescale "83xx" based
platforms to crash on boot due to some PCI breakage"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Fix boot panic on mpc83xx (regression)
|
|
To replace down() with down_interrutible() to avoid following
warning:
[c00000007ba7b710] [c000000000014410] .__switch_to+0x1b0/0x380
[c00000007ba7b7c0] [c0000000007b408c] .__schedule+0x3ec/0x970
[c00000007ba7ba50] [c0000000007b1f24] .schedule_timeout+0x1a4/0x2b0
[c00000007ba7bb30] [c0000000007b34a4] .__down+0xa4/0x104
[c00000007ba7bbf0] [c0000000000b9230] .down+0x60/0x70
[c00000007ba7bc80] [c0000000000336d0] .eeh_event_handler+0x70/0x190
[c00000007ba7bd30] [c0000000000b1a58] .kthread+0xe8/0xf0
[c00000007ba7be30] [c00000000000a05c] .ret_from_kernel_thread+0x5c/0x8
This also avoids keeping the load average up while doing nothing.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Originally, eeh_mutex was introduced to protect the PE hierarchy
tree and the attached EEH devices because EEH core was possiblly
running with multiple threads to access the PE hierarchy tree.
However, we now have only one kthread in EEH core. So we needn't
the eeh_mutex and just remove it.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Building with CONFIG_TRANSPARENT_HUGEPAGE disabled causes the following
build wearnings;
powerpc/arch/powerpc/include/asm/mmu-hash64.h: In function ‘__hash_page_thp’:
powerpc/arch/powerpc/include/asm/mmu-hash64.h:354: warning: no return statement in function returning non-void
This patch adds a return -1 to the static inline for __hash_page_thp()
to correct the warnings.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Since now we have pstore support for nvram in pseries, enable it
in the default config. With this config option enabled, pstore
infra-structure will be used to read/write the messages from/to nvram.
Signed-off-by: Aruna Balakrishnaiah <aruna@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In 9422de3 "powerpc: Hardware breakpoints rewrite to handle non DABR breakpoint
registers" we changed the way we mark extraneous irqs with this:
- info->extraneous_interrupt = !((bp->attr.bp_addr <= dar) &&
- (dar - bp->attr.bp_addr < bp->attr.bp_len));
+ if (!((bp->attr.bp_addr <= dar) &&
+ (dar - bp->attr.bp_addr < bp->attr.bp_len)))
+ info->type |= HW_BRK_TYPE_EXTRANEOUS_IRQ;
Unfortunately this is bogus as it never clears extraneous IRQ if it's already
set.
This correctly clears extraneous IRQ before possibly setting it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The smallest match region for both the DABR and DAWR is 8 bytes, so the
kernel needs to filter matches when users want to look at regions smaller than
this.
Currently we set the length of PPC_BREAKPOINT_MODE_EXACT breakpoints to 8.
This is wrong as in exact mode we should only match on 1 address, hence the
length should be 1.
This ensures that the kernel will filter out any exact mode hardware breakpoint
matches on any addresses other than the requested one.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Enable USB EHCI, mass storage and USB gadget support.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
