| Age | Commit message (Collapse) | Author |
|---|
|
On rsk devices provide a dummy regulator for the smsc911x driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269. NOR Flash, SDRAM, serial, USB Host and
ethernet are working.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The RSK2+SH7264 board uses the sh7264 processor. It is often
referred to as just rsk7264. NOR Flash, SDRAM, serial, USB Host and
ethernet are working.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The RSK+ setup code was doing some pretty dubious things with
parse_mtd_partitions() in order to populate the physmap-flash map
platform data. The physmap-flash driver contains all of the functionality
that we require already, so simply drop the special casing and pad out
the platform data accordingly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Now that there's an upstream polled gpio-keys driver, add the outstanding
platform data for it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix the rsk7203 board code to build with CONFIG_MTD=n.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds support for the LAN9118 ethernet on rsk7203.
The LAN9118 controller is hooked up using a 16-bit data bus,
but the rsk7203 board does not swap the byte lanes as needed
between the sh7203 processor and the the ethernet controller.
In the processor the CS memory window is configured in 16-bit
mode but the smsc911x driver is told to do 32-bit accesses to
improve performance. The SMSC911X_SWAP_FIFO flag is used
to tell the driver to do software byte swapping of fifo data.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix up the build for mach-highlander and mach-rsk. These operated on the
assumption that GENERIC_GPIO support with an optional GPIOLIB was
possible. This used to be true, but has not been the case since commit-id
d56cc8bc661ac1ceded8d45ba2d53bb134fee17d ("sh: use gpiolib"), where the
GENERIC_GPIO implementation was rewritten to use GPIOLIB directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
RSK+ platforms have quite a few characteristics in common, so roll them
together in to a shiny new RSK mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
