| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds MSIOF and mmc_spi platform data for
the CN11 port on the SuperH Ecovec24 board. No card
detect interrupt is available so the MMC code is
configured to poll. The WP signal is implemented
together with CD and power control. The board only
supports 3.3V power.
The platform data is wrapped in SDHI #ifdefs to
allow both the SDHI and the MSIOF to coexist. Only
one configuration is allowed at a time. The pin
routing is selected by a dip switch but we can
unfortunately not detect this setting at run time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
sh/for-2.6.33
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
|
|
Current soc-camera needs SOCAM_DATA_ACTIVE_xxx flags for use.
We can not open old ncm03j camera device without this patch.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds a ->start_transfer() callback to the
KFR2R09 lcd handling code. The callback is used to
notify the lcd controller that a new frame of data
is about to be transferred. The callback is only used
in combination with deferred io, but the code has
been tested both with and without deferred io enabled.
Without this patch the display data on the KFR2R09
lcd panel becomes corrupted over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Drive ability for LCDC become high for safety,
became there is strange individual specificity board in mass production
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch improves the serial port communication quality
of port YC401 on the KFR2R09 board. With this fix serial
console is fine at 115200 - up and down keys now work as
expected. Thanks to Hirohide Yamasaki for this fix.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch adds support for SDHI power control to the
Ecovec board. Platform data and power control callbacks
for SDHI0 and SDHI1 are added. Power is by default off.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This is a port of the sound/oss/sh_dac_audio.c driver.
The driver uses an on-chip 8-bit D/A converter, which has a speaker connected
to one of its channels, found in several ancient HP machines.
For interrupts it uses a high-resolution timer (hrtimer).
Tested on SH7709 based hp6xx (HP Jornada 680/690 and HP Palmtop 620lx/660lx).
Also, since OSS Emulation works, the old OSS sound/oss/sh_dac_audio.c driver
would be obsolete soon, and it could be removed.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The indexes are signed, make sure they are not negative
when we read array elements.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This gets rid of the arbitrary set of vectors used by the SE7722 FPGA
interrupt controller and witches over to a completely dynamic set.
No assumptions regarding a contiguous range are made, and the platform
resources themselves need to be filled in lazily.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Get rid of the unused WP signal for SDHI0 on KFR2R09.
This because yc304 on KFR2R09 is a Micro SD slot which
does not implement the WP signal.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Update the SDHI platform data for the AP325RXA board
to include support for the CN7 Micro SD Card slot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add R-standby support to the KFR2R09 sdram code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add self-refresh handling code for the Ecovec24 board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add self-refresh handling code for the AP325RXA board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Move the AP325RXA board code from a single board file
to a separate directory. This to make it easy to add
support for sdram sleep mode code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add self-refresh handling code for the Migo-R board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add self-refresh handling code for the MS7724SE board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add self-refresh handling code for the KFR2R09 board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
USB1 can change to host/function by checking PTB3.
This patch add USB1 gadget support and check PTB3 when boot,
and change name to usb1_common_XXX from usb1_host_XXX.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add support for cn8 and SDHI1 to the ms7724se board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the ms7724se board code to pass the mac
address to the sh_eth driver using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the ecovec24 board code to pass the mac
address to the sh_eth driver using platform data.
Also, remove the static clock to allow Runtime PM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add HWBLK_ETHER to the sh_eth platform device
to allow Runtime PM of the ethernet hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Fix the rsk7203 board code to build with CONFIG_MTD=n.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Conflicts:
arch/sh/boards/mach-ecovec24/setup.c
arch/sh/boards/mach-kfr2r09/setup.c
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add SD Card support to the kfr2r09 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and yc304.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Add SD Card support to the se7724 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and CN7.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the AP325 board to use sh_mobile_sdhi for the
SD Card connected to CN3 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the Migo-R board to use sh_mobile_sdhi for the
SD Card connected to CN9 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Conflicts:
arch/sh/mm/cache-sh4.c
|
|
The open function got the BKL via the big push down. Replace it by
preempt_enable/disable as this is sufficient for an UP machine.
The ioctl can be unlocked because there is no functionality which
requires serialization. The usage by multiple callers is broken with
and without the BKL due to the local static variable addr.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Extend the ecovec24 board code to enable Power
Management LEDs showing the current sh7724 sleep state.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Tested-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
There is now no need for the magicpanelr2 and dreamcast platforms to set
their own I/O port bas values, given that the generic machvec code now
sets this to P2SEG for everyone.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We will be registering and unregistering the soc_camera_platform platform
device multiple times, therefore we need a .release() method and have to
nullify the kobj.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Update ap325rxa to specify .bus_id in struct soc_camera_link explicitly, remove
unused .iface from struct soc_camera_platform_info.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
