summaryrefslogtreecommitdiffstats
path: root/arch/sh
AgeCommit message (Collapse)Author
2009-08-15sh: sh7724 ddr self-refresh changesMagnus Damm
This patch updates the SuperH Mobile sleep assembly code with support for DBSC memory controller found in the sh7724 processor. Without this fix the memory hooked up to the sh7724 processor will never enter self-refresh mode before suspending to ram. The effect of this is that the memory contents most likeley will be lost upon resume which may or may not be what you want. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-15sh: use in-soc KEYSC on se7724Magnus Damm
This patch updates the Solution Engine 7724 board code to use in-SoC KEYSC resources for the keyboard platform device. Using the in-SoC key scan controller fixes a crash-during-resume issue. Without this patch the KEYSC hardware block located in the board specific FPGA is used together with an external IRQ which is routed through the FPGA and handled by some board specific demux code. This board specific FPGA interrupt code does not implement desc->set_wake() so the enable_irq_wake() call in the sh_keysc driver will fail at suspend-to-ram time and the disable_irq_wake() will bomb out when resuming. Changing the platform data to use the in-SoC KEYSC hardware makes the se7724 board support code less special which is a good thing. Also, the board specific KEYSC pin setup code selects in-SoC pin functions already which makes the current FPGA platform device data look like a typo. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-13sh: fix i2c init order on ap325rxa V2Magnus Damm
Convert the AP325RXA board code to register devices at arch_initcall() time instead of device_initcall(). This fix unbreaks pcf8563 RTC driver support. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-13sh: fix i2c init order on Migo-R V2Magnus Damm
Convert the Migo-R board code to register devices at arch_initcall() time instead of __initcall(). This fix unbreaks migor_ts touch screen driver support. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-08-13sh: convert processor device setup functions to arch_initcall()Magnus Damm
Convert the processor platform device setup functions from __initcall() and sometimes device_initcall() to arch_initcall(). This makes sure that the platform devices are registered a bit earlier so the devices are available when drivers register using initcall levels earlier than device_initcall(). A good example is platform devices needed by i2c-sh_mobile.c which registers a bit earlier using subsys_initcall(). Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-27mm: Remove duplicate definitions in MIPS and SHBenjamin Herrenschmidt
Those definitions are already provided by asm-generic Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-27mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()Benjamin Herrenschmidt
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() Upcoming paches to support the new 64-bit "BookE" powerpc architecture will need to have the virtual address corresponding to PTE page when freeing it, due to the way the HW table walker works. Basically, the TLB can be loaded with "large" pages that cover the whole virtual space (well, sort-of, half of it actually) represented by a PTE page, and which contain an "indirect" bit indicating that this TLB entry RPN points to an array of PTEs from which the TLB can then create direct entries. Thus, in order to invalidate those when PTE pages are deleted, we need the virtual address to pass to tlbilx or tlbivax instructions. The old trick of sticking it somewhere in the PTE page struct page sucks too much, the address is almost readily available in all call sites and almost everybody implemets these as macros, so we may as well add the argument everywhere. I added it to the pmd and pud variants for consistency. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV] Acked-by: Nick Piggin <npiggin@suse.de> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-12headers: smp_lock.h reduxAlexey Dobriyan
* Remove smp_lock.h from files which don't need it (including some headers!) * Add smp_lock.h to files which do need it * Make smp_lock.h include conditional in hardirq.h It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT This will make hardirq.h inclusion cheaper for every PREEMPT=n config (which includes allmodconfig/allyesconfig, BTW) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-10sched: INIT_PREEMPT_COUNTPeter Zijlstra
Pull the initial preempt_count value into a single definition site. Maintainers for: alpha, ia64 and m68k, please have a look, your arch code is funny. The header magic is a bit odd, but similar to the KERNEL_DS one, CPP waits with expanding these macros until the INIT_THREAD_INFO macro itself is expanded, which is in arch/*/kernel/init_task.c where we've already included sched.h so we're good. Cc: tony.luck@intel.com Cc: rth@twiddle.net Cc: geert@linux-m68k.org Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-07-05sh: add r8a66597 usb0 host to the se7724 boardMagnus Damm
Add USB host support for port CN27 on the Solution Engine 7724 board. The r8a66597-hcd driver is hooked up as a platform device and some registers are configured to enable the USB host function. The hardware driving the USB port is the on-chip USB0 block in the sh7724 processor configured as USB host controller. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-03sh: define PERF_COUNTER_INDEX_OFFSET.Paul Mundt
Fixes up recent build breakage. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-02sh: Fix compiler error and include the definition of IS_ERR_VALUEMatt Fleming
When arch/sh/include/asm/syscall_32.h is included from a file that doesn't also include linux/err.h the following error is produced, In file included from /home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall.h:5, from kernel/trace/trace_syscalls.c:3: /home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h: In function 'syscall_get_error': /home/matt/src/kernels/sh-2.6/arch/sh/include/asm/syscall_32.h:28: error: implicit declaration of function 'IS_ERR_VALUE' make[2]: *** [kernel/trace/trace_syscalls.o] Error 1 make[1]: *** [kernel/trace] Error 2 make: *** [kernel] Error 2 Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-01sh: re-add LCDC fbdev support to the Migo-R defconfigMagnus Damm
Re-add LCDC fbdev support to the Migo-R defconfig. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-07-01sh: fix se7724 ceu namesMagnus Damm
Use "ceu0" and "ceu1" as CEU names instead of "ceu". This fixes "memchunk" kernel command line selection on the solution engine 7724 board. With this patch applied use "memchunk.ceu0=1m" or "memchunk.ceu1=1m" on kernel command line to override physically memory size to one meg for CEU0 or CEU1. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-29sh: ms7724se: Enable sh_eth in defconfig.Kuninori Morimoto
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-29arch/sh/boards/mach-se/7206/io.c: Remove unnecessary semicolonsJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-26sh: ms7724se: Add sh_eth supportKuninori Morimoto
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-25sh: Kill off unused DEBUG_BOOTMEM symbol.Paul Mundt
This was killed off in generic code some time ago, kill off the left over symbol. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-25sh64: Hook up page fault events for software perf counters.Paul Mundt
sh64 can use these as well, so tie them up there as well. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-25sh: Hook up page fault events for software perf counters.Paul Mundt
This adds page fault instrumentation for the software performance counters. Follows the x86 and powerpc changes. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-24sh: make set_perf_counter_pending() static inline.Paul Mundt
Fixes up a recently introduced build error. Reported-by: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-24sh: Fix up HAVE_PERF_COUNTERS typo.Paul Mundt
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right initially but I seem to have screwed it up while re-typing it out by hand on another machine when I checked it in. Hmph. Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-23sh: Fix up more dma-mapping fallout.Paul Mundt
commit dbe6f1869188b6e04e38aa861dd198befb08bcd7 ("dma-mapping: mark dma_sync_single and dma_sync_sg as deprecated" conveniently broke every single SH build. In the future it would be great if people could at least bother figuring out how to use grep. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-23sh: SH7786 SMP support.Paul Mundt
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2 CPUs. This just wraps in to the existing SH-X3 SMP code with some minor changes for SH7786, including wiring up the IPIs properly, enabling IRQ_PER_CPU, and so forth. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-23sh: Wire up the uncached fixmap on sh64 as well.Paul Mundt
Now that sh64 also can use the uncached section, wire up the fixmap for it as well. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-23sh: Use local TLB flush in set_pte_phys().Paul Mundt
set_pte_phys() presently uses the global flush_tlb_one(), which locks on SMP trying to do the IPI. As we have not even initialized the other CPUs at this point, switch to the local_ variant so the flush happens on the boot CPU. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-23sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.Paul Mundt
Crib the x86 cpu_idle_wait() implementation and shove it in with the idle code, subsequently enabling ARCH_HAS_CPU_IDLE_WAIT. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-21Move FAULT_FLAG_xyz into handle_mm_fault() callersLinus Torvalds
This allows the callers to now pass down the full set of FAULT_FLAG_xyz flags to handle_mm_fault(). All callers have been (mechanically) converted to the new calling convention, there's almost certainly room for architectures to clean up their code and then add FAULT_FLAG_RETRY when that support is added. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (56 commits) sh: Fix declaration of __kernel_sigreturn and __kernel_rt_sigreturn sh: Enable soc-camera in ap325rxa/migor/se7724 defconfigs. sh: remove stray markers. sh: defconfig updates. sh: pci: Initial PCI-Express support for SH7786 Urquell board. sh: Generic HAVE_PERF_COUNTER support. SH: convert migor to soc-camera as platform-device SH: convert ap325rxa to soc-camera as platform-device soc-camera: unify i2c camera device platform data sh: add platform data for r8a66597-hcd in setup-sh7723 sh: add platform data for r8a66597-hcd in setup-sh7366 sh: x3proto: add platform data for r8a66597-hcd sh: highlander: add platform data for r8a66597-hcd sh: sh7785lcr: add platform data for r8a66597-hcd sh: turn off irqs when disabling CMT/TMU timers sh: use kzalloc() for cpg clocks sh: unbreak WARN_ON() sh: Use generic atomic64_t implementation. sh: Revised clock function in highlander sh: Update r7780mp defconfig ...
2009-06-18ptrace: remove PT_DTRACE from avr32, mn10300, parisc, s390, sh, xtensaOleg Nesterov
avr32, mn10300, parisc, s390, sh, xtensa: They never set PT_DTRACE, but clear it after do_execve(). Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: David Howells <dhowells@redhat.com> Acked-by: Kyle McMartin <kyle@mcmartin.ca> Cc: Grant Grundler <grundler@parisc-linux.org> Cc: Matthew Wilcox <matthew@wil.cx> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Chris Zankel <chris@zankel.net> Acked-by: Roland McGrath <roland@redhat.com> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-18sh: Fix declaration of __kernel_sigreturn and __kernel_rt_sigreturnMatt Fleming
GCC 4.5.0 complains about the declaration of variables __kernel_sigreturn and __kernel_rt_sigreturn because they have type void. Correctly declare these symbols as functions to fix the following error, arch/sh/kernel/signal_32.c: In function 'setup_frame': arch/sh/kernel/signal_32.c:368:14: error: taking address of expression of type 'void' arch/sh/kernel/signal_32.c: In function 'setup_rt_frame': arch/sh/kernel/signal_32.c:452:14: error: taking address of expression of type 'void' make[1]: *** [arch/sh/kernel/signal_32.o] Error 1 make: *** [arch/sh/kernel] Error 2 Signed-off-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-18sh: Enable soc-camera in ap325rxa/migor/se7724 defconfigs.Paul Mundt
The MEDIA_SUPPORT option disabled soc-camera support, so re-enable it for the impacted defconfigs. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-18sh: remove stray markers.Christoph Hellwig
arch/sh has a couple of stray markers without any users introduced in commit 3d58695edbfac785161bf282dc11fd42a483d6c9. Remove them in preparation of removing the markers in favour of the TRACE_EVENT macro (and also because we don't keep dead code around). Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-18sh: defconfig updates.Paul Mundt
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17Delete pcibios_select_rootMatthew Wilcox
This function was only used by pci_claim_resource(), and the last commit deleted that use. Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-17sh: pci: Initial PCI-Express support for SH7786 Urquell board.Paul Mundt
This adds initial support for the PCI-Express module in the SH7786, particularly as it relates to the urquell platform. Presently it is only supported in root complex mode, with endpoint mode still requiring more debugging. 29/32-bit mode and lane configurations are selectable via board mode pins, and are otherwise fixed. Only 4x and 1x PCI channels are presently handled, the PCI bridge still requires additional debugging and stabilization in hardware. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17Merge branches 'sh/pci-express-integration', 'sh/rsk-updates', ↵Paul Mundt
'sh/platform-updates' and 'sh/perf_counter'
2009-06-17sh: Generic HAVE_PERF_COUNTER support.Paul Mundt
This enables support for the generic software-based perf counters. Hardware counter support could be added in the future, but the lack of a performance counter IRQ makes this rather dubious. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17SH: convert migor to soc-camera as platform-deviceGuennadi Liakhovetski
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17SH: convert ap325rxa to soc-camera as platform-deviceGuennadi Liakhovetski
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17soc-camera: unify i2c camera device platform dataGuennadi Liakhovetski
Unify i2c camera device platform data to point to struct soc_camera_link for a smooth transition to soc-camera as a platform driver. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: add platform data for r8a66597-hcd in setup-sh7723Yoshihiro Shimoda
and remove redundant parameter for r8a66597-hcd. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: add platform data for r8a66597-hcd in setup-sh7366Yoshihiro Shimoda
and remove redundant parameter for r8a66597-hcd. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: x3proto: add platform data for r8a66597-hcdYoshihiro Shimoda
and remove redundant parameter for r8a66597-hcd. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: highlander: add platform data for r8a66597-hcdYoshihiro Shimoda
and remove redundant parameter for r8a66597-hcd. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: sh7785lcr: add platform data for r8a66597-hcdYoshihiro Shimoda
and remove redundant parameter for r8a66597-hcd. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: use kzalloc() for cpg clocksMagnus Damm
Convert the shared clock cpg code from bootmem to slab. Without this patch the current bootmem code triggers WARN_ON() because the slab is available. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-17sh: unbreak WARN_ON()Magnus Damm
Fix WARN_ON() by modifying the bug trap handling code to always return in the in-kernel instruction pointer case. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-06-16kmap_types: make most arches use generic header fileRandy Dunlap
Convert most arches to use asm-generic/kmap_types.h. Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h, controlled by __WITH_KM_FENCE from each arch's kmap_types.h file. Would be nice to be able to add custom KM_types per arch, but I don't yet see a nice, clean way to do that. Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and 68k(tonyb). Note: avr32 should be able to remove KM_PTE2 (since it's not used) and then just use the generic kmap_types.h file. Get avr32 maintainer approval. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: <linux-arch@vger.kernel.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Bryan Wu <cooloney@kernel.org> Cc: Mikael Starvik <starvik@axis.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: "Luck Tony" <tony.luck@intel.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Howells <dhowells@redhat.com> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-16mm: consolidate init_mm definitionAlexey Dobriyan
* create mm/init-mm.c, move init_mm there * remove INIT_MM, initialize init_mm with C99 initializer * unexport init_mm on all arches: init_mm is already unexported on x86. One strange place is some OMAP driver (drivers/video/omap/) which won't build modular, but it's already wants get_vm_area() export. Somebody should look there. [akpm@linux-foundation.org: add missing #includes] Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Mike Frysinger <vapier.adi@gmail.com> Cc: Americo Wang <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>