| Age | Commit message (Collapse) | Author |
|---|
|
This change sets the PCI devices' initial DMA capabilities
conservatively and promotes them at the request of the driver,
as opposed to assuming advanced DMA capabilities. The old design
runs the risk of breaking drivers that assume default capabilities.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The standard kernel function dma_get_required_mask() uses the
highest DRAM address to determine if 32-bit or 64-bit DMA addressing
is needed. This only works on architectures that have direct mapping
between the PA and the PCI address space, i.e. those that don't have
I/O TLBs or have I/O TLB but choose to use direct mapping. Neither
of these are true for tilegx. Whether to use 64-bit DMA should depend
on the PCI device's capability only, not on the amount of DRAM
installeds, so we now advertise a 64-bit DMA mask unconditionally.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The LSI MEGARAID SAS HBA suffers from the problem where it can do
64-bit DMA to streaming buffers but not to consistent buffers.
In other words, 64-bit DMA is used for disk data transfers and 32-bit
DMA must be used for control message transfers. According to LSI,
the firmware is not fully functional yet. This change implements a
kind of hybrid dma_ops to support this.
Note that on most other platforms, the 64-bit DMA addressing space is the
same as the 32-bit DMA space and they overlap the physical memory space.
No special arrangement is needed to support this kind of mixed DMA
capability. On TILE-Gx, the 64-bit DMA space is completely separate
from the 32-bit DMA space. Due to the use of the IOMMU, the 64-bit DMA
space doesn't overlap the physical memory space. On the other hand,
the 32-bit DMA space overlaps the physical memory space under 4GB.
The separate address spaces make it necessary to have separate dma_ops.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Add dma-debug interface debug_dma_mapping_error() to debug drivers that fail
to check dma mapping errors on addresses returned by dma_map_single() and
dma_map_page() interfaces.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
|
|
This change uses the TRIO IOMMU to map the PCI DMA space and physical
memory at different addresses. We also now use the dma_mapping_ops
to provide support for non-PCI DMA, PCIe DMA (64-bit) and legacy PCI
DMA (32-bit). We use the kernel's software I/O TLB framework
(i.e. bounce buffers) for the legacy 32-bit PCI device support since
there are a limited number of TLB entries in the IOMMU and it is
non-trivial to handle indexing, searching, matching, etc. For 32-bit
devices the performance impact of bounce buffers should not be a concern.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Since v2.6.20 "Pass struct dev pointer to dma_cache_sync()"
(d3fa72e4556ec1f04e46a0d561d9e785ecaa173d), dma_cache_sync() takes a
struct dev pointer, but these appear to be missing from the tile and
mn10300 implementations, so add them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[cmetcalf@tilera.com: took only the "tile" portion as I don't maintain mn10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This change is the core kernel support for TILEPro and TILE64 chips.
No driver support (except the console driver) is included yet.
This includes the relevant Linux headers in asm/; the low-level
low-level "Tile architecture" headers in arch/, which are
shared with the hypervisor, etc., and are build-system agnostic;
and the relevant hypervisor headers in hv/.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
|
